main
Ray Publish 0.1.0 565173f

NCP1230D165R2G

onsemi · AC-DC Controllers & Regulators · SOIC-7

NCP1230D165R2G from onsemi, in a SOIC-7. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 PFC VCC power_out Provides bias voltage to the PFC controller through a low impedance switch connected to VCC, and goes down in standby and fault conditions.
2 FB input An optocoupler collector pulls this pin low to regulate, and the controller skips cycles when the current setpoint reaches 25% of the maximum peak.
3 CS/OVP input Combines the current sense function, an internal ramp compensation signal and a 3.0 V latch-off level that latches the output off until VCC is recycled.
4 GND power_in IC ground reference for the controller.
5 DRV output Drives large Qg MOSFETs with a drive capability of +500 mA / −800 mA.
6 VCC power_in Accepts voltages up to 18 V and features a UVLO turn-off threshold of 7.7 V typical.
8 HV power_in Connects to the bulk voltage to provide a lossless startup sequence, with charging current high enough to support the PWM controller bias needs through pin 1.

Key specifications

Parameter Value
Manufacturer onsemi
Package SOIC-7
Category Power Supply Chip
Pins 7

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Turn-On Threshold Level, VCC Going Up VCCOFF 11.6 12.6 13.6 V VCC Going Up (Vfb = 2.0 V) 5
Minimum Operating Voltage after Turn-On VCC(min) 7 7.7 8.4 V 5
VCC Decreasing Level at which the Latch-Off Phase Ends VCClatch 5 5.6 6.2 V Vfb = 3.5 V 5
Internal IC Consumption, No Output Load on Pin 6 ICC1 0.6 1.1 1.8 mA No Output Load on Pin 6 (Vfb = 2.5 V) 5
Internal IC Consumption, 1.0 nF Output Load on Pin 6, FSW = 65 kHz ICC2 1.3 1.8 2.5 mA 1.0 nF Output Load on Pin 6, FSW = 65 kHz (Vfb = 2.5 V) 5
Internal IC Consumption, Latch-Off Phase ICC3 400 680 1000 A Latch-Off Phase 5
High-Voltage Current Source, 1.0 nF Load IC1 1.8 3.2 4.2 mA 1.0 nF Load (VCCOFF -0.2 V, Vfb = 2.5 V, VPIN8 = 30 V) 5
High-Voltage Current Source (VCC = 0 V) IC2 1.8 4.4 5.6 mA VCC = 0 V 5
Minimum Startup Voltage VHVmin 20 23 V Ic = 0.5 mA, VCCOFF -0.2 V, Vfb = 2.5 V 5
Startup Leakage IHVLeak 10 30 80 A VPIN8 = 500 V 5
Source Resistance ROH 6 12.3 25 ohm RLoad 300 (Vfb = 2.5 V) 5
Sink Resistance ROL 3 7.5 18 ohm at 1.0 V on Pin 5 (Vfb = 3.5 V) 5
Pin 1 Output Impedance (Rdson between Pin 1 and Pin 6 when SW1 is closed) RPFC 6 11.7 23 ohm Rload on Pin 1 = 680 5
Maximum Internal Current Setpoint ILimit 1.01 1.063 1.116 V Tj = 25°C 5
Maximum Internal Current Setpoint ILimit 0.979 1.127 V Tj = -40°C to +125°C 5
Default Internal Setpoint for Skip Cycle Operation and Standby Detection Vskip 600 750 900 mV 5
Default Internal Setpoint to Leave Standby Vstby-out 1 1.25 1.5 V 5
Propagation Delay from CS Detected to Gate Turned Off TDEL 90 180 ns VGate = 10 V (Pin 5 Loaded by 1.0 nF) 5
Leading Edge Blanking Duration TLEB 100 200 350 ns 5
Temperature Shutdown, Maximum Value (Note 3) TSD 150 165 °C Note 3 5
Oscillation Frequency, 65 kHz Version fOSC 60 65 70 kHz Vfb = 2.5 V, Tj = 25°C 6
Oscillation Frequency, 65 kHz Version fOSC 58 72 kHz Tj = 0°C to +125°C (Vfb = 2.5 V) 6
Oscillation Frequency, 65 kHz Version fOSC 55 72 kHz Tj = -40°C to +125°C (Vfb = 2.5 V) 6
Maximum Duty-Cycle Dmax 75 80 85 % CS = 0, Vfb = 2.5 V 6
Internal Resistor Rup 9 18 36 k 6
Opto Current Source Iopto 200 235 270 A Vfb = 0.75 V 6
Latch-Off Level Vlatch 2.7 3 3.3 V 6
Supply Voltage, Pin 6 (VCC) VCC -0.3 18 V Pin 6 4
Current, Pin 6 (ICC2) ICC2 100 mA Pin 6 4
Maximum Voltage on Pin 8 (VDS) VDS -0.3 500 V Pin 8 4
Maximum Current on Pin 8 (IC2) IC2 100 mA Pin 8 4
Drive Output Voltage, Pin 5 VDV 18 V Pin 5 4
Drive Current, Pin 5 Io 1 A Pin 5 4
Voltage Current Sense Pin, Pin 3 Vcs 10 V Pin 3 4
Current Sense Pin, Pin 3 Ics 100 mA Pin 3 4
Voltage Feedback, Pin 2 Vfb 10 V Pin 2 4
Current Feedback, Pin 2 Ifb 100 mA Pin 2 4
Voltage, Pin 1 VPFC 18 V Pin 1 4
Maximum Continuous Current Flowing from Pin 1 IPFC 35 mA Pin 1 4
Maximum Power Dissipation SOIC Pmax 0.702 W TA = 25°C 4
Maximum Junction Temperature TJ 150 °C 4
Storage Temperature Range Tstg -60 150 °C 4
Thermal Resistance, Junction-to-Air, SOIC Version RJA 178 °C/W SOIC version 4

CAD (KiCad official)

  • Symbol: NCP1230D165R2G
  • Footprint: Package_SO:SOIC-8-N7_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-7 (KiCad packages3D, STEP)
  • 3D model files: ncp1230d165r2g-etched.step / ncp1230d165r2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncp1230d165r2g.step / ncp1230d165r2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (24 pp, sha256 dea329b276fa1926, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF