Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
NCP1230D165R2G
onsemi · AC-DC Controllers & Regulators · SOIC-7
NCP1230D165R2G from onsemi, in a SOIC-7. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PFC VCC | power_out | Provides bias voltage to the PFC controller through a low impedance switch connected to VCC, and goes down in standby and fault conditions. |
| 2 | FB | input | An optocoupler collector pulls this pin low to regulate, and the controller skips cycles when the current setpoint reaches 25% of the maximum peak. |
| 3 | CS/OVP | input | Combines the current sense function, an internal ramp compensation signal and a 3.0 V latch-off level that latches the output off until VCC is recycled. |
| 4 | GND | power_in | IC ground reference for the controller. |
| 5 | DRV | output | Drives large Qg MOSFETs with a drive capability of +500 mA / −800 mA. |
| 6 | VCC | power_in | Accepts voltages up to 18 V and features a UVLO turn-off threshold of 7.7 V typical. |
| 8 | HV | power_in | Connects to the bulk voltage to provide a lossless startup sequence, with charging current high enough to support the PWM controller bias needs through pin 1. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-7 |
| Category | Power Supply Chip |
| Pins | 7 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Turn-On Threshold Level, VCC Going Up | VCCOFF | 11.6 | 12.6 | 13.6 | V | VCC Going Up (Vfb = 2.0 V) | 5 |
| Minimum Operating Voltage after Turn-On | VCC(min) | 7 | 7.7 | 8.4 | V | 5 | |
| VCC Decreasing Level at which the Latch-Off Phase Ends | VCClatch | 5 | 5.6 | 6.2 | V | Vfb = 3.5 V | 5 |
| Internal IC Consumption, No Output Load on Pin 6 | ICC1 | 0.6 | 1.1 | 1.8 | mA | No Output Load on Pin 6 (Vfb = 2.5 V) | 5 |
| Internal IC Consumption, 1.0 nF Output Load on Pin 6, FSW = 65 kHz | ICC2 | 1.3 | 1.8 | 2.5 | mA | 1.0 nF Output Load on Pin 6, FSW = 65 kHz (Vfb = 2.5 V) | 5 |
| Internal IC Consumption, Latch-Off Phase | ICC3 | 400 | 680 | 1000 | A | Latch-Off Phase | 5 |
| High-Voltage Current Source, 1.0 nF Load | IC1 | 1.8 | 3.2 | 4.2 | mA | 1.0 nF Load (VCCOFF -0.2 V, Vfb = 2.5 V, VPIN8 = 30 V) | 5 |
| High-Voltage Current Source (VCC = 0 V) | IC2 | 1.8 | 4.4 | 5.6 | mA | VCC = 0 V | 5 |
| Minimum Startup Voltage | VHVmin | 20 | 23 | V | Ic = 0.5 mA, VCCOFF -0.2 V, Vfb = 2.5 V | 5 | |
| Startup Leakage | IHVLeak | 10 | 30 | 80 | A | VPIN8 = 500 V | 5 |
| Source Resistance | ROH | 6 | 12.3 | 25 | ohm | RLoad 300 (Vfb = 2.5 V) | 5 |
| Sink Resistance | ROL | 3 | 7.5 | 18 | ohm | at 1.0 V on Pin 5 (Vfb = 3.5 V) | 5 |
| Pin 1 Output Impedance (Rdson between Pin 1 and Pin 6 when SW1 is closed) | RPFC | 6 | 11.7 | 23 | ohm | Rload on Pin 1 = 680 | 5 |
| Maximum Internal Current Setpoint | ILimit | 1.01 | 1.063 | 1.116 | V | Tj = 25°C | 5 |
| Maximum Internal Current Setpoint | ILimit | 0.979 | 1.127 | V | Tj = -40°C to +125°C | 5 | |
| Default Internal Setpoint for Skip Cycle Operation and Standby Detection | Vskip | 600 | 750 | 900 | mV | 5 | |
| Default Internal Setpoint to Leave Standby | Vstby-out | 1 | 1.25 | 1.5 | V | 5 | |
| Propagation Delay from CS Detected to Gate Turned Off | TDEL | 90 | 180 | ns | VGate = 10 V (Pin 5 Loaded by 1.0 nF) | 5 | |
| Leading Edge Blanking Duration | TLEB | 100 | 200 | 350 | ns | 5 | |
| Temperature Shutdown, Maximum Value (Note 3) | TSD | 150 | 165 | °C | Note 3 | 5 | |
| Oscillation Frequency, 65 kHz Version | fOSC | 60 | 65 | 70 | kHz | Vfb = 2.5 V, Tj = 25°C | 6 |
| Oscillation Frequency, 65 kHz Version | fOSC | 58 | 72 | kHz | Tj = 0°C to +125°C (Vfb = 2.5 V) | 6 | |
| Oscillation Frequency, 65 kHz Version | fOSC | 55 | 72 | kHz | Tj = -40°C to +125°C (Vfb = 2.5 V) | 6 | |
| Maximum Duty-Cycle | Dmax | 75 | 80 | 85 | % | CS = 0, Vfb = 2.5 V | 6 |
| Internal Resistor | Rup | 9 | 18 | 36 | k | 6 | |
| Opto Current Source | Iopto | 200 | 235 | 270 | A | Vfb = 0.75 V | 6 |
| Latch-Off Level | Vlatch | 2.7 | 3 | 3.3 | V | 6 | |
| Supply Voltage, Pin 6 (VCC) | VCC | -0.3 | 18 | V | Pin 6 | 4 | |
| Current, Pin 6 (ICC2) | ICC2 | 100 | mA | Pin 6 | 4 | ||
| Maximum Voltage on Pin 8 (VDS) | VDS | -0.3 | 500 | V | Pin 8 | 4 | |
| Maximum Current on Pin 8 (IC2) | IC2 | 100 | mA | Pin 8 | 4 | ||
| Drive Output Voltage, Pin 5 | VDV | 18 | V | Pin 5 | 4 | ||
| Drive Current, Pin 5 | Io | 1 | A | Pin 5 | 4 | ||
| Voltage Current Sense Pin, Pin 3 | Vcs | 10 | V | Pin 3 | 4 | ||
| Current Sense Pin, Pin 3 | Ics | 100 | mA | Pin 3 | 4 | ||
| Voltage Feedback, Pin 2 | Vfb | 10 | V | Pin 2 | 4 | ||
| Current Feedback, Pin 2 | Ifb | 100 | mA | Pin 2 | 4 | ||
| Voltage, Pin 1 | VPFC | 18 | V | Pin 1 | 4 | ||
| Maximum Continuous Current Flowing from Pin 1 | IPFC | 35 | mA | Pin 1 | 4 | ||
| Maximum Power Dissipation SOIC | Pmax | 0.702 | W | TA = 25°C | 4 | ||
| Maximum Junction Temperature | TJ | 150 | °C | 4 | |||
| Storage Temperature Range | Tstg | -60 | 150 | °C | 4 | ||
| Thermal Resistance, Junction-to-Air, SOIC Version | RJA | 178 | °C/W | SOIC version | 4 |
CAD (KiCad official)
- Symbol:
NCP1230D165R2G - Footprint:
Package_SO:SOIC-8-N7_3.9x4.9mm_P1.27mm - 3D model: SOIC-7 (KiCad packages3D, STEP)
- 3D model files:
ncp1230d165r2g-etched.step/ncp1230d165r2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncp1230d165r2g.step/ncp1230d165r2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (24 pp, sha256
dea329b276fa1926, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).