main
Ray ncp110amx180tbg: specified limits as data (metadata.characteristics, 35 rows from the datasheet) b871436

NCP110AMX180TBG

onsemi · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · XDFN-4-EP(1x1)

NCP110AMX180TBG from onsemi, in a XDFN-4-EP(1x1). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OUT power_out Regulated output voltage pin (1.8 V nominal for the 180 suffix). Must be bypassed to GND with a small 1 µF ceramic capacitor. Sources up to 200 mA with typical dropout of 65 mV at 200 mA (VOUT = 1.8 V).
2 GND power_in Common ground reference for the regulator. Return path for input, output, and control currents.
3 EN input Chip enable input. VEN < 0.2 V disables the regulator (shutdown, IDIS ~0.01 µA typ); VEN > 0.7 V enables the LDO. Internal ~0.2 µA pull-down on the pin; absolute max -0.3 V to 6 V.
4 IN power_in Input voltage supply pin. Operating range 1.1 V to 5.5 V (absolute max 6 V). Bypass to GND with a 1 µF ceramic capacitor close to the pin.
EPAD EPAD passive Exposed thermal pad on the underside of the XDFN-4 package. Tie to the ground plane for improved power dissipation (RθJA reduces on adequate copper).

Key specifications

Parameter Value
Manufacturer onsemi
Package XDFN-4-EP(1x1)
Category PMIC
Pins 5

Ordering variants

Same part, different packaging or reel option.

  • NCP110AMX180TBG
  • NCP110AMX180TBGMU

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operating Input Voltage VIN 1.1 5.5 V 4
Output Voltage Accuracy (VOUT(NOM) > 1.5 V) VOUT -2 2 % VIN = VOUT(NOM) + 0.3 V (VIN ≥ 1.1 V); VOUT(NOM) > 1.5 V 4
Dropout Voltage VDO 65 120 mV VOUT(NOM) = 1.80 V, IOUT = 200 mA 4
Output Current Limit ICL 225 300 mA VOUT = 90% VOUT(NOM) 4
Short Circuit Current ISC 300 mA VOUT = 0 V 4
Quiescent Current IQ 20 25 µA IOUT = 0 mA 4
Shutdown Current IDIS 0.01 1 µA VEN ≤ 0.2 V, VIN = 1.1 V 4
EN Input Voltage High VENH 0.7 V 4
EN Input Voltage Low VENL 0.2 V 4
EN Pull Down Current IEN 0.2 0.5 µA VEN = 1.1 V 4
Turn-On Time tON 120 µs COUT = 1 µF, from assertion of VEN to VOUT = 95% VOUT(NOM) 4
Line Regulation LineReg 0.02 %/V VOUT(NOM) + 0.5 V ≤ VIN ≤ 5.5 V, (VIN ≥ 1.1 V) 4
Load Regulation LoadReg 0.001 %/mA IOUT = 1 mA to 200 mA 4
Power Supply Rejection Ratio PSRR 90 dB IOUT = 20 mA, VIN = VOUT + 0.3 V, f = 100 Hz 4
Power Supply Rejection Ratio PSRR 95 dB IOUT = 20 mA, VIN = VOUT + 0.3 V, f = 1 kHz 4
Power Supply Rejection Ratio PSRR 85 dB IOUT = 20 mA, VIN = VOUT + 0.3 V, f = 10 kHz 4
Power Supply Rejection Ratio PSRR 55 dB IOUT = 20 mA, VIN = VOUT + 0.3 V, f = 100 kHz 4
Output Voltage Noise VN 8.8 VRMS f = 10 Hz to 100 kHz 4
Thermal Shutdown Threshold (rising) TSDH 160 °C Temperature rising 4
Thermal Shutdown Threshold (falling) TSDL 140 °C Temperature falling 4
Active Output Discharge Resistance RDIS 280 Ω VEN < 0.2 V, Version A only 4
Input Voltage VIN -0.3 6 V 3
Output Voltage VOUT -0.3 6 V Upper limit VIN + 0.3 V, max. 6 V 3
Chip Enable Input VCE -0.3 6 V 3
Maximum Junction Temperature TJ 150 °C 3
Storage Temperature TSTG -55 150 °C 3
ESD Capability, Human Body Model ESDHBM 2000 V JESD22-A114 3
ESD Capability, Machine Model ESDMM 200 V JESD22-A115 3
Thermal Resistance, Junction-to-Air, XDFN4 RJA 208 °C/W Note 3: measured per JEDEC board, JESD51-7 3
Operating Junction Temperature Range TJ -40 125 °C Electrical characteristics range 4
Input Capacitor (CIN) CIN 1 µF X7R or X5R recommended 13
Output Capacitor (COUT) recommended value COUT 1 µF X7R or X5R dielectric 13
Output Capacitor (COUT) minimum effective capacitance COUT 0.6 µF Over temperature, DC bias and package size 13
Output Capacitor (COUT) ESR ESR 1.6 Ω Maximum ESR of COUT 13
Nominal Output Voltage VOUT(NOM) 1.8 V Ordering table, NCP110AMX180TBG 15

CAD (KiCad official)

  • Symbol: NCP110AMX180TBG
  • Footprint: Package_DFN_QFN:OnSemi_XDFN4-1EP_1.0x1.0mm_EP0.52x0.52mm
  • 3D model: XDFN-4-EP(1x1) (KiCad packages3D, STEP)
  • 3D model files: ncp110amx180tbg-etched.step / ncp110amx180tbg-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncp110amx180tbg.step / ncp110amx180tbg.glb are the bare package body.

3D model downloads

Two STEP files. Same geometry, different body top:

File Size Use it when
ncp110amx180tbg.step 144 KB You want the bare part, or you mark your own boards.
ncp110amx180tbg-etched.step 2.4 MB You want the part with NCP110AMX180TBG already on it.

The marking in the etched file is real recessed geometry cut into the solid, not a texture or a decal: 596 faces against 41 in the bare model. It survives export, section views, and rendering in any CAD tool, and it drops straight into KiCad or Fusion with no extra setup.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (18 pp, sha256 852726895c73c069, retrieved 2026-08-17, tier: lcsc)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF