main
History Download
Ray Publish 0.1.0 755d399

NCL30001DR2G

onsemi · LED Drivers · SOIC-16

NCL30001DR2G from onsemi, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CT passive An external timing capacitor sets the oscillator frequency, with a sawtooth between 0.2 V and 4 V that also sets the multiplier gain.
2 RAMP COMP passive A resistor (RRC) from this pin to ground sets the ramp compensation added to the current signal, and this pin should not be left open.
3 AC IN input The scaled full-wave rectified input AC voltage is connected through a resistive divider and is used by the multiplier.
4 FB input The feedback error signal from an external error amplifier via an optocoupler enters Soft-Skip when FB drops below 0.41 V (typical) to reduce acoustic noise.
5 VFF input Feedforward input receiving a scaled, filtered rectified line voltage through a resistive divider and averaging capacitor for the Reference Generator.
6 CM output Multiplier output that requires a capacitor to ground to filter the modulated output of the multiplier.
7 AC COMP passive Sets the pole of the AC reference amplifier and should not be left open.
8 Latch input Latch-Off input that latches the controller when pulled below 1.0 V (typical) or above 7.0 V (typical).
9 TEST passive Test pin that requires a nominal 50 kΩ 10% resistor to GND for proper operation.
10 IAVG passive An external resistor and capacitor from this pin to ground set and stabilize the gain of the current sense amplifier output driving the AC error amplifier.
11 ISpos input Positive current sense input connected to the positive side of the current sense resistor.
12 VCC power_in Positive supply input with an external energy-storage capacitor; outputs are enabled above approximately 15.3 V and drivers are disabled below approximately 10.2 V.
13 DRV output Drive output for the main flyback power MOSFET or IGBT, with 10.8 Ω (typical) source resistance and 8 Ω (typical) sink resistance.
14 NC unconnected No connect.
15 GND power_in Ground reference for the circuit.
16 HV power_in Connects to the rectified input line voltage to enable the internal startup regulator, supplying a typical 5.5 mA charge current to the VCC capacitor with a maximum input voltage of 500 V.

Key specifications

Parameter Value
Manufacturer onsemi
Package SOIC-16
Category Display Modules / LED Drivers / Display Drivers
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Oscillator Frequency fosc 90 100 110 kHz 6
Maximum Duty Ratio D 94 % RTEST = open 6
Source Current IEA(source) 25 70 A VAC COMP = 2.0 V, VAC IN = 2.0 V, VFF = 1.0 V 6
Sink Current IEA(sink) -25 -70 A VAC COMP = 2.0 V, VAC_IN = 2.0 V, VFF = 5.0 V 6
Input Bias Current (current amplifier) CAIbias 40 53 80 A VISPOS = 0 V 6
Input Offset Voltage (current amplifier) CAVIO -20 0 20 mV VAC COMP = 5.0 V, VISpos = 0 V 6
Current Limit Threshold VILIM 0.695 0.74 0.77 V force DRV high, VAC COMP = 3.0 V, ramp VISPOS, VRamp_Comp = open 6
PWM Output Voltage Gain PWMk 4 5.3 6 V/V 6
Current Limit Voltage Gain ISVk 15.4 18.5 23 V/V 6
Reference Generator output voltage (low input ac line and full load) RGout1 3.61 4.36 4.94 Vpk VAC IN = 1.2 V, VFF = 0.765 V, VFB = 4 V 6
Reference Generator output voltage (high input ac line and full load) RGout2 1.16 1.35 1.61 Vpk VAC IN = 3.75 V, VFF = 2.39 V, VFB = 4.0 V 6
Reference Generator output voltage (low input as line and minimum load) RGout3 1.85 2.18 2.58 Vpk VAC IN = 1.2 V, VFF = 0.765 V, VFB = 2.0 V 6
Reference Generator output voltage (high input ac line and minimum load) RGout4 0.55 0.65 0.78 Vpk VAC IN = 3.75 V, VFF = 2.39 V, VFB = 2.0 V 6
Reference Generator output offset voltage RGoffset -100 100 mV 6
Drive Resistance (Thermally Limited) DRV Sink RSNK 8 18 VDRV = 1 V, IDRV = 100 mA 7
Drive Resistance (Thermally Limited) DRV Source RSRC 10.8 24 VDRV = 1 V, IDRV = 100 mA 7
Driver Out Low Voltage VDRV(low) 1 100 mV IDRV = 100 A 7
Skip Synchronization to ac Line Voltage Threshold VSSKIP(SYNC) 210 267 325 mV VACIN Increasing, VFB = 1.5 V 7
Skip Voltage Threshold VSSKIP 360 410 460 V 7
Skip Voltage Hysteresis VSSKIP(HYS) 45 90 140 mV 7
Pull-Up Current Source IFB 600 750 920 A VFB = 0.5 V 7
Open Circuit Voltage VFB(open) 5.3 5.7 6.3 V 7
Supply Voltage Startup Threshold VCC(on) 14.3 15.4 16.3 V VCC Increasing 7
Supply Voltage Minimum Operating Voltage VCC(off) 9.3 10.2 11.3 V VCC Decreasing 7
Inhibit Threshold Voltage Vinhibit 0.83 1.15 V VHV = 40 V, Iinhibit = 500 A 7
Inhibit Bias Current Iinhibit 40 500 A VHV = 40 V, VCC = 0.8 * Vinhibit 7
Minimum Startup Voltage Vstart(min) 40 V Istart = 0.5 mA, VCC = VCC(on), 0.5 V 7
Startup Current Istart 3 5.62 8 mA VCC = VCC(on), 0.5 V, VFB = Open 7
Off-State Leakage Current IHV(off) 17 40 A VHV = 400 V, TJ = 25C 7
Off-State Leakage Current IHV(off) 15 80 A TJ = −40C to 125C 7
Supply Current Device Disabled (Overload) ICC1 0.72 1.2 mA VFB = Open 7
Supply Current Device Switching ICC2 6.25 7.2 mA VFB = Open, fOSC ≥ 100 kHz 7
Overload Timer tOVLD 120 160 360 ms 7
Overload Detect Threshold VOVLD 4.7 4.9 5.2 V 8
Brown-Out Detect Threshold (entering fault mode) VBO(low) 0.41 0.45 0.49 V VFF Decreasing, VFB = 2.5 V, VAC IN = 2.0 V 8
Brown-Out Exit Threshold (exiting fault mode) VBO(high) 0.57 0.63 0.69 V VFF Increasing, VFB = 2.5 V, VAC IN = 2.0 V 8
Latch Pull-Down Voltage Threshold Vlatch(low) 0.9 0.98 1.1 V VLatch Decreasing 8
Latch Pull-Up Voltage Threshold Vlatch(high) 5.6 7 8.4 V VLatch Increasing 8
Latch Propagation Delay tlatch(delay) 30 56 90 s VLatch = Vlatch(high) 8
Latch Clamp Current (Going Out) Ilatch(clamp) 42 51 58 A VLatch = 1.5 V 8
Latch Clamp Voltage (ILatch Going In) Vlatch(clamp) 2.5 3.27 4.5 V ILatch = 50 A 8
Input Offset Voltage (AC error amplifier) ACVIO 40 mV Ramp IAVG, VFB = 0 V 6

CAD (KiCad official)

  • Symbol: NCL30001DR2G
  • Footprint: Package_SO:SOIC-16_3.9x9.9mm_P1.27mm
  • 3D model: SOIC-16 (KiCad packages3D, STEP)
  • 3D model files: ncl30001dr2g-etched.step / ncl30001dr2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncl30001dr2g.step / ncl30001dr2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (33 pp, sha256 a470345fa8053ae6, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF