Generated by kicad-footprint-generator · KiCad file format 20260206
NCL30001DR2G
onsemi · LED Drivers · SOIC-16
NCL30001DR2G from onsemi, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CT | passive | An external timing capacitor sets the oscillator frequency, with a sawtooth between 0.2 V and 4 V that also sets the multiplier gain. |
| 2 | RAMP COMP | passive | A resistor (RRC) from this pin to ground sets the ramp compensation added to the current signal, and this pin should not be left open. |
| 3 | AC IN | input | The scaled full-wave rectified input AC voltage is connected through a resistive divider and is used by the multiplier. |
| 4 | FB | input | The feedback error signal from an external error amplifier via an optocoupler enters Soft-Skip when FB drops below 0.41 V (typical) to reduce acoustic noise. |
| 5 | VFF | input | Feedforward input receiving a scaled, filtered rectified line voltage through a resistive divider and averaging capacitor for the Reference Generator. |
| 6 | CM | output | Multiplier output that requires a capacitor to ground to filter the modulated output of the multiplier. |
| 7 | AC COMP | passive | Sets the pole of the AC reference amplifier and should not be left open. |
| 8 | Latch | input | Latch-Off input that latches the controller when pulled below 1.0 V (typical) or above 7.0 V (typical). |
| 9 | TEST | passive | Test pin that requires a nominal 50 kΩ 10% resistor to GND for proper operation. |
| 10 | IAVG | passive | An external resistor and capacitor from this pin to ground set and stabilize the gain of the current sense amplifier output driving the AC error amplifier. |
| 11 | ISpos | input | Positive current sense input connected to the positive side of the current sense resistor. |
| 12 | VCC | power_in | Positive supply input with an external energy-storage capacitor; outputs are enabled above approximately 15.3 V and drivers are disabled below approximately 10.2 V. |
| 13 | DRV | output | Drive output for the main flyback power MOSFET or IGBT, with 10.8 Ω (typical) source resistance and 8 Ω (typical) sink resistance. |
| 14 | NC | unconnected | No connect. |
| 15 | GND | power_in | Ground reference for the circuit. |
| 16 | HV | power_in | Connects to the rectified input line voltage to enable the internal startup regulator, supplying a typical 5.5 mA charge current to the VCC capacitor with a maximum input voltage of 500 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-16 |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Oscillator Frequency | fosc | 90 | 100 | 110 | kHz | 6 | |
| Maximum Duty Ratio | D | 94 | % | RTEST = open | 6 | ||
| Source Current | IEA(source) | 25 | 70 | A | VAC COMP = 2.0 V, VAC IN = 2.0 V, VFF = 1.0 V | 6 | |
| Sink Current | IEA(sink) | -25 | -70 | A | VAC COMP = 2.0 V, VAC_IN = 2.0 V, VFF = 5.0 V | 6 | |
| Input Bias Current (current amplifier) | CAIbias | 40 | 53 | 80 | A | VISPOS = 0 V | 6 |
| Input Offset Voltage (current amplifier) | CAVIO | -20 | 0 | 20 | mV | VAC COMP = 5.0 V, VISpos = 0 V | 6 |
| Current Limit Threshold | VILIM | 0.695 | 0.74 | 0.77 | V | force DRV high, VAC COMP = 3.0 V, ramp VISPOS, VRamp_Comp = open | 6 |
| PWM Output Voltage Gain | PWMk | 4 | 5.3 | 6 | V/V | 6 | |
| Current Limit Voltage Gain | ISVk | 15.4 | 18.5 | 23 | V/V | 6 | |
| Reference Generator output voltage (low input ac line and full load) | RGout1 | 3.61 | 4.36 | 4.94 | Vpk | VAC IN = 1.2 V, VFF = 0.765 V, VFB = 4 V | 6 |
| Reference Generator output voltage (high input ac line and full load) | RGout2 | 1.16 | 1.35 | 1.61 | Vpk | VAC IN = 3.75 V, VFF = 2.39 V, VFB = 4.0 V | 6 |
| Reference Generator output voltage (low input as line and minimum load) | RGout3 | 1.85 | 2.18 | 2.58 | Vpk | VAC IN = 1.2 V, VFF = 0.765 V, VFB = 2.0 V | 6 |
| Reference Generator output voltage (high input ac line and minimum load) | RGout4 | 0.55 | 0.65 | 0.78 | Vpk | VAC IN = 3.75 V, VFF = 2.39 V, VFB = 2.0 V | 6 |
| Reference Generator output offset voltage | RGoffset | -100 | 100 | mV | 6 | ||
| Drive Resistance (Thermally Limited) DRV Sink | RSNK | 8 | 18 | VDRV = 1 V, IDRV = 100 mA | 7 | ||
| Drive Resistance (Thermally Limited) DRV Source | RSRC | 10.8 | 24 | VDRV = 1 V, IDRV = 100 mA | 7 | ||
| Driver Out Low Voltage | VDRV(low) | 1 | 100 | mV | IDRV = 100 A | 7 | |
| Skip Synchronization to ac Line Voltage Threshold | VSSKIP(SYNC) | 210 | 267 | 325 | mV | VACIN Increasing, VFB = 1.5 V | 7 |
| Skip Voltage Threshold | VSSKIP | 360 | 410 | 460 | V | 7 | |
| Skip Voltage Hysteresis | VSSKIP(HYS) | 45 | 90 | 140 | mV | 7 | |
| Pull-Up Current Source | IFB | 600 | 750 | 920 | A | VFB = 0.5 V | 7 |
| Open Circuit Voltage | VFB(open) | 5.3 | 5.7 | 6.3 | V | 7 | |
| Supply Voltage Startup Threshold | VCC(on) | 14.3 | 15.4 | 16.3 | V | VCC Increasing | 7 |
| Supply Voltage Minimum Operating Voltage | VCC(off) | 9.3 | 10.2 | 11.3 | V | VCC Decreasing | 7 |
| Inhibit Threshold Voltage | Vinhibit | 0.83 | 1.15 | V | VHV = 40 V, Iinhibit = 500 A | 7 | |
| Inhibit Bias Current | Iinhibit | 40 | 500 | A | VHV = 40 V, VCC = 0.8 * Vinhibit | 7 | |
| Minimum Startup Voltage | Vstart(min) | 40 | V | Istart = 0.5 mA, VCC = VCC(on), 0.5 V | 7 | ||
| Startup Current | Istart | 3 | 5.62 | 8 | mA | VCC = VCC(on), 0.5 V, VFB = Open | 7 |
| Off-State Leakage Current | IHV(off) | 17 | 40 | A | VHV = 400 V, TJ = 25C | 7 | |
| Off-State Leakage Current | IHV(off) | 15 | 80 | A | TJ = −40C to 125C | 7 | |
| Supply Current Device Disabled (Overload) | ICC1 | 0.72 | 1.2 | mA | VFB = Open | 7 | |
| Supply Current Device Switching | ICC2 | 6.25 | 7.2 | mA | VFB = Open, fOSC ≥ 100 kHz | 7 | |
| Overload Timer | tOVLD | 120 | 160 | 360 | ms | 7 | |
| Overload Detect Threshold | VOVLD | 4.7 | 4.9 | 5.2 | V | 8 | |
| Brown-Out Detect Threshold (entering fault mode) | VBO(low) | 0.41 | 0.45 | 0.49 | V | VFF Decreasing, VFB = 2.5 V, VAC IN = 2.0 V | 8 |
| Brown-Out Exit Threshold (exiting fault mode) | VBO(high) | 0.57 | 0.63 | 0.69 | V | VFF Increasing, VFB = 2.5 V, VAC IN = 2.0 V | 8 |
| Latch Pull-Down Voltage Threshold | Vlatch(low) | 0.9 | 0.98 | 1.1 | V | VLatch Decreasing | 8 |
| Latch Pull-Up Voltage Threshold | Vlatch(high) | 5.6 | 7 | 8.4 | V | VLatch Increasing | 8 |
| Latch Propagation Delay | tlatch(delay) | 30 | 56 | 90 | s | VLatch = Vlatch(high) | 8 |
| Latch Clamp Current (Going Out) | Ilatch(clamp) | 42 | 51 | 58 | A | VLatch = 1.5 V | 8 |
| Latch Clamp Voltage (ILatch Going In) | Vlatch(clamp) | 2.5 | 3.27 | 4.5 | V | ILatch = 50 A | 8 |
| Input Offset Voltage (AC error amplifier) | ACVIO | 40 | mV | Ramp IAVG, VFB = 0 V | 6 |
CAD (KiCad official)
- Symbol:
NCL30001DR2G - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files:
ncl30001dr2g-etched.step/ncl30001dr2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncl30001dr2g.step/ncl30001dr2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (33 pp, sha256
a470345fa8053ae6, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).