Generated by kicad-footprint-generator · KiCad file format 20260206
N79E814AS20
Nuvoton Tech · Microcontroller Units (MCUs/MPUs/SOCs) · SOP-20-300mil
N79E814AS20 from Nuvoton Tech, in a SOP-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | P0.0 | bidirectional | Port 0 bit 0, quasi-bidirectional after reset, multiplexed as PWM3 output, KB0 keyboard interrupt input and SPICLK (SPI-1 clock); Port 0 is configurable through P0M1/P0M2 and P0.0 is the PWM3 output when driven high for PWM. |
| 2 | P1.7 | bidirectional | Port 1 bit 7, quasi-bidirectional after reset, multiplexed as PWM2 output, ICPCLK (in-circuit programming serial clock), and MOSI (SPI-1); during ICP programming all pins are set to quasi-bidirectional with output high. |
| 3 | P1.6 | bidirectional | Port 1 bit 6, quasi-bidirectional after reset, multiplexed as PWM1 output, ICPDAT (in-circuit programming data I/O) and MISO (SPI-1). |
| 4 | RST | input | Active-low Schmitt-trigger reset input; the internal pull-up is about 200 kΩ so the pin must not be left floating, and the datasheet calls for a 100 Ω pull-up resistor and 10 µF capacitor to ground. |
| 5 | VSS | power_in | Ground reference for the device. |
| 6 | P3.1 | bidirectional | Port 3 bit 1, used as XTAL1 (input to the inverting amplifier of the external crystal/resonator oscillator); when an external crystal is used P3.1 cannot be used as an I/O pin. |
| 7 | P3.0 | bidirectional | Port 3 bit 0, used as XTAL2 (output of the internal oscillator amplifier) or as CLKOUT, which outputs the internal RC clock divided by 4 when ENCLK is set; it cannot be used as I/O when an external crystal is used. |
| 8 | P1.4 | bidirectional | Port 1 bit 4, quasi-bidirectional, multiplexed as external interrupt /INT1, ADC start input STADC and SPI-1 slave select /SS. |
| 9 | P1.3 | bidirectional | Port 1 bit 3, open-drain when I2C is enabled (required for SDA), multiplexed as external interrupt /INT0 and I2C data line SDA; an external pull-up is required when used as output. |
| 10 | P1.2 | bidirectional | Port 1 bit 2, always open-drain (I2C clock SCL), multiplexed as Timer 0 external input T0 and input capture IC0; an external pull-up is required. |
| 11 | P1.1 | bidirectional | Port 1 bit 1, quasi-bidirectional, multiplexed as UART receive RXD (selectable to P2.7 via AUXR1.6). |
| 12 | P1.0 | bidirectional | Port 1 bit 0, quasi-bidirectional, multiplexed as UART transmit TXD (selectable to P2.6 via AUXR1.6). |
| 13 | P0.7 | bidirectional | Port 0 bit 7, quasi-bidirectional, multiplexed as Timer 1 external input T1, ADC channel 6 input, KB7 keyboard interrupt and input capture IC1; in ADC use the input voltage must stay between AVSS and Vref+. |
| 14 | P0.6 | bidirectional | Port 0 bit 6, quasi-bidirectional, multiplexed as ADC channel 5 input and KB6 keyboard interrupt input. |
| 15 | VDD | power_in | Supply voltage: 2.4 V to 5.5 V at FOSC 4-12 MHz and 3.0 V to 5.5 V at FOSC 4-24 MHz per the DC electrical table (Section 2 states 4.5 V to 5.5 V for 24 MHz). |
| 16 | P0.5 | bidirectional | Port 0 bit 5, quasi-bidirectional, multiplexed as ADC channel 4 input and KB5 keyboard interrupt input. |
| 17 | P0.4 | bidirectional | Port 0 bit 4, quasi-bidirectional, multiplexed as ADC channel 3 input and KB4 keyboard interrupt input. |
| 18 | P0.3 | bidirectional | Port 0 bit 3, quasi-bidirectional, multiplexed as ADC channel 2 input and KB3 keyboard interrupt input. |
| 19 | P0.2 | bidirectional | Port 0 bit 2, quasi-bidirectional, multiplexed as ADC channel 1 input, KB2 keyboard interrupt input and BRAKE (PWM clamp/fault input, active level selected by PWMCON1.6). |
| 20 | P0.1 | bidirectional | Port 0 bit 1, quasi-bidirectional, multiplexed as PWM0 output, ADC channel 0 input and KB1 keyboard interrupt input. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Nuvoton Tech |
| Package | SOP-20-300mil |
| Category | Embedded Processors & Controllers |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating temperature | -40 | 85 | C | 166 | |||
| Storage temperature | -55 | 150 | C | 166 | |||
| VDD to VSS voltage | -0.3 | 6.5 | V | 166 | |||
| Voltage on other pins to VSS | -0.3 | V | max printed as (VDD+0.3) | 166 | |||
| Operating voltage VDD | VDD | 3 | 5.5 | V | Fosc = 4 MHz ~ 24 MHz | 166 | |
| Operating voltage VDD | VDD | 2.4 | 5.5 | V | Fosc = 4 MHz ~12 MHz | 166 | |
| Input low voltage (standard port TTL input) | VIL | -0.5 | V | 2.4< VDD< 5.5V; max printed as 0.2VDD-0.1 | 166 | ||
| Input low voltage (standard port Schmitt input) | VIL1 | -0.5 | V | 2.4< VDD< 5.5V; max printed as 0.3VDD | 166 | ||
| Input low voltage (/RST, XTAL1) | VIL2 | -0.5 | V | 2.4< VDD< 5.5V; max printed as 0.2VDD-0.1 | 166 | ||
| Output low voltage (standard port P0, P2) | VOL | 0.45 | V | VDD=4.5V, IOL= 20 mA | 167 | ||
| Output low voltage (P10, P11, P14, P16, P17) | VOL1 | 0.45 | V | VDD=4.5V, IOL= 38 mA | 167 | ||
| Output high voltage (standard port, quasi-bidirectional) | VOH | 2.4 | V | VDD=4.5V, IOH= -380 μA | 167 | ||
| Output high voltage (standard port, quasi-bidirectional) | VOH | 2 | V | VDD=2.4V, IOH= -48 μA | 167 | ||
| Output high voltage (standard port, push-pull) | VOH1 | 2.4 | V | VDD=4.5V, IOH= -28.0 mA | 167 | ||
| Output high voltage (standard port, push-pull) | VOH1 | 2 | V | VDD=2.4V, IOH= -3.5 mA | 167 | ||
| Logic 0 input current (standard port, quasi-bidirectional) | IIL | -50 | -40 | μA | VDD=5.5V, VIN=0.4V | 167 | |
| Logic 1 to 0 transition current (standard port, quasi-bidirectional) | ITL | -650 | -550 | μA | VDD=5.5V, VIN=2.0V | 167 | |
| Input leakage current | ILI | -10 | 10 | μA | 0 < VIN< VDD <1 | 167 | |
| Operating current (normal mode) | IOP | 3.1 | mA | XTAL 12MHz, VDD=5.0V | 167 | ||
| Operating current (normal mode) | IOP | 4.3 | mA | XTAL 24MHz, VDD=5.5V | 167 | ||
| Operating current (normal mode) | IOP | 1.7 | mA | XTAL 12MHz, VDD=3.3V | 168 | ||
| Operating current (normal mode) | IOP | 3.2 | mA | XTAL 24MHz, VDD=3.3V | 168 | ||
| Operating current (normal mode) | IOP | 2.8 | mA | 内部晶振 22.1184MHz,VDD=5V | 168 | ||
| Idle mode operating current | IIDLE | 2.7 | mA | XTAL 12MHz, VDD=5.0V | 168 | ||
| Idle mode operating current | IIDLE | 3.7 | mA | XTAL 24MHz, VDD=5.5V | 168 | ||
| Idle mode operating current | IIDLE | 1.3 | mA | XTAL 12MHz, VDD=3.3V | 168 | ||
| Idle mode operating current | IIDLE | 2.3 | mA | XTAL 24MHz, VDD=3.3V | 168 | ||
| Idle mode operating current | IIDLE | 2 | mA | 内部RC 晶振 22.1184MHz,VDD=5V | 168 | ||
| Power-down mode operating current | IPD | 30 | μA | 168 | |||
| Reset pin internal pull-up resistance | RRST | 100 | 250 | KΩ | 2.4< VDD< 5.5V | 168 | |
| BOD38 detection voltage | VBOD38 | 3.5 | 3.8 | 4.1 | V | 温度=25℃ | 168 |
| BOD38 detection voltage | VBOD38 | 3.5 | 3.8 | 4.9 | V | 温度=85℃ | 168 |
| BOD38 detection voltage | VBOD38 | 3 | 3.8 | 4.1 | V | 温度=-40℃ | 168 |
| BOD27 detection voltage | VBOD27 | 2.5 | 2.7 | 2.9 | V | 温度=25℃ | 168 |
| BOD27 detection voltage | VBOD27 | 2.5 | 2.7 | 3.1 | V | 温度=85℃ | 168 |
| BOD27 detection voltage | VBOD27 | 2.4 | 2.7 | 2.9 | V | 温度=-40℃ | 168 |
| ADC operating voltage | VDD | 2.7 | 5.5 | V | 169 | ||
| Integral nonlinearity error | INL | -1 | 1 | LSB | 169 | ||
| Differential nonlinearity error | DNL | -1 | 1 | LSB | 169 | ||
| Gain error | Ge | -1 | 1 | LSB | 169 | ||
| Offset error | Ofe | -4 | 4 | LSB | 169 | ||
| Bandgap reference voltage | VBG | 1 | 1.3 | 1.6 | V | 169 | |
| External clock input frequency (external crystal source) | 4 | 24 | MHz | 外部晶振源 | 170 | ||
| Clock high time | tCHCX | 20.8 | Ns | 170 | |||
| Clock low time | tCLCX | 20.8 | Ns | 170 | |||
| Clock rise time | tCLCH | 10 | Ns | 170 | |||
| Clock fall time | tCHCL | 10 | Ns | 170 | |||
| Internal RC oscillator center frequency | 22.1184 | MHz | 170 | ||||
| Internal oscillator frequency deviation | -1 | 1 | % | +250C @ VDD=5V | 170 | ||
| Internal oscillator frequency deviation | -3 | 3 | % | +250C @ VDD=2.7~5.5V | 170 | ||
| Internal oscillator frequency deviation | -5 | 5 | % | -100C~+700C @ VDD=2.7~5.5V | 170 | ||
| Internal oscillator frequency deviation | -8 | 8 | % | -400C~+850C @ VDD=2.7~5.5V | 170 |
CAD (KiCad official)
- Symbol:
N79E814AS20 - Footprint:
Package_SO:SOP-20_7.5x12.8mm_P1.27mm - 3D model: SOP-20-300mil, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 2.65 mm nominal SOIC height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
n79e814as20-etched.step/n79e814as20-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);n79e814as20.step/n79e814as20.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Nuvoton Tech datasheet (179 pp, sha256
d6a503318845ce88, retrieved 2026-10-28, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).