component
MX25L51245GMI-08G
Public Made by Adomby adom
MXIC(Macronix) NOR FLASH, SOP-16-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
1485a08
MX25L51245GMI-08G
MXIC(Macronix) · NOR FLASH · SOP-16-300mil
MX25L51245GMI-08G from MXIC(Macronix), in a SOP-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC/SIO3 | bidirectional | No connection in single and dual I/O operation; becomes serial data input and output SIO3 in 4 x I/O read mode. |
| 2 | VCC | power_in | Power supply pin (+3V); the DC and AC characteristics are specified for VCC = 2.7V to 3.6V. |
| 3 | RESET# | input | Hardware reset input, active low; the internal pull-up stays active only while the pin is not physically connected in the system. |
| 4 | NC | unconnected | No connection. |
| 5 | DNU | unconnected | Do Not Use; it may connect to an internal signal inside the device, so leave it unconnected. |
| 6 | DNU | unconnected | Do Not Use; it may connect to an internal signal inside the device, so leave it unconnected. |
| 7 | CS# | input | Chip select input, active low; serial access to the device is enabled while CS# is low. |
| 8 | SO/SIO1 | bidirectional | Serial data output in single I/O mode; serial data input and output SIO1 in 2 x I/O or 4 x I/O read mode. |
| 9 | WP#/SIO2 | bidirectional | Write protection input, active low, or serial data input and output SIO2 in 4 x I/O read mode; the internal pull-up stays active only while the pin is not physically connected. |
| 10 | GND | power_in | Ground reference. |
| 11 | DNU | unconnected | Do Not Use; it may connect to an internal signal inside the device, so leave it unconnected. |
| 12 | DNU | unconnected | Do Not Use; it may connect to an internal signal inside the device, so leave it unconnected. |
| 13 | NC | unconnected | No connection. |
| 14 | NC | unconnected | No connection. |
| 15 | SI/SIO0 | bidirectional | Serial data input in single I/O mode; serial data input and output SIO0 in 2 x I/O or 4 x I/O read mode. |
| 16 | SCLK | input | Clock input for the serial interface. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MXIC(Macronix) |
| Package | SOP-16-300mil |
| Category | Memory |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Load Current | ILI | -2 | 2 | uA | VCC = VCC Max, VIN = VCC or GND | 118 | |
| Output Leakage Current | ILO | -2 | 2 | uA | VCC = VCC Max, VOUT = VCC or GND | 118 | |
| VCC Standby Current | ISB1 | 20 | 100 | uA | VIN = VCC or GND, CS# = VCC | 118 | |
| Deep Power-down Current | ISB2 | 20 | uA | VIN = VCC or GND, CS# = VCC | 118 | ||
| VCC Read current (DTR 4 x I/O read, 100MHz) | ICC1 | 30 | mA | f=100MHz, (DTR 4 x I/O read), SCLK=0.1VCC/0.9VCC, SO=Open | 118 | ||
| VCC Read current (4 x I/O read, 104MHz) | ICC1 | 20 | mA | f=104MHz, (4 x I/O read), SCLK=0.1VCC/0.9VCC, SO=Open | 118 | ||
| VCC Read current (84MHz) | ICC1 | 15 | mA | f=84MHz, SCLK=0.1VCC/0.9VCC, SO=Open | 118 | ||
| VCC Program Current (PP) | ICC2 | 20 | 25 | mA | Program in Progress, CS# = VCC | 118 | |
| VCC Write Status Register (WRSR) Current | ICC3 | 20 | mA | Program status register in progress, CS#=VCC | 118 | ||
| VCC Sector/Block (32K, 64K) Erase Current (SE/BE/BE32K) | ICC4 | 20 | 25 | mA | Erase in Progress, CS#=VCC | 118 | |
| VCC Chip Erase Current (CE) | ICC5 | 20 | 25 | mA | Erase in Progress, CS#=VCC | 118 | |
| Input Low Voltage | VIL | -0.5 | 0.8 | V | 118 | ||
| Output Low Voltage | VOL | 0.2 | V | IOL = 100uA | 118 | ||
| Clock Frequency for all commands (except Read Operation) | fSCLK | 166 | MHz | Clock frequency for all commands except Read Operation | 119 | ||
| Clock Frequency for READ instructions | fRSCLK | 66 | MHz | Clock Frequency for READ instructions | 119 | ||
| Clock High Time | tCH | 7 | ns | <= 66MHz (fSCLK) | 119 | ||
| Clock Low Time | tCL | 7 | ns | <= 66MHz (fSCLK) | 119 | ||
| Clock Rise Time (peak to peak) | tCLCH | 0.1 | V/ns | peak to peak | 119 | ||
| Clock Fall Time (peak to peak) | tCHCL | 0.1 | V/ns | peak to peak | 119 | ||
| CS# Active Setup Time (relative to SCLK) | tSLCH | 3 | ns | 119 | |||
| CS# Not Active Hold Time (relative to SCLK) | tCHSL | 4 | ns | 119 | |||
| Data In Setup Time | tDVCH | 2 | ns | 119 | |||
| Data In Hold Time | tCHDX | 2 | ns | VCC: 2.7V - 3.6V | 119 | ||
| Data In Hold Time | tCHDX | 1 | ns | VCC: 3.0V - 3.6V (Loading: 15pF/10pF) | 119 | ||
| CS# Active Hold Time (relative to SCLK) | tCHSH | 3 | ns | 119 | |||
| CS# Not Active Setup Time (relative to SCLK) | tSHCH | 3 | ns | 119 | |||
| CS# Deselect Time | tSHSL | 7 | ns | From Read to next Read | 119 | ||
| CS# Deselect Time | tSHSL | 30 | ns | From Write/Erase/Program to Read Status Register | 119 | ||
| Output Disable Time | tSHQZ | 8 | ns | 119 | |||
| Clock Low to Output Valid | tCLQV | 8 | ns | VCC: 2.7V - 3.6V, Loading: 30pF | 119 | ||
| Clock Low to Output Valid | tCLQV | 6 | ns | VCC: 2.7V - 3.6V, Loading: 15pF | 119 | ||
| Clock Low to Output Valid | tCLQV | 5 | ns | VCC: 2.7V - 3.6V, Loading: 10pF | 119 | ||
| Clock Low to Output Valid | tCLQV | 4.5 | ns | VCC: 3.0V - 3.6V, Loading: 10pF, ODS (1,1,0) | 119 | ||
| Output Hold Time | tCLQX | 1 | ns | Loading: 30pF | 119 | ||
| Write Protect Setup Time | tWHSL | 20 | ns | 119 | |||
| Write Protect Hold Time | tSHWL | 100 | ns | 119 | |||
| CS# High to Deep Power-down Mode | tDP | 10 | us | 119 | |||
| CS# High to Standby Mode with Electronic Signature Read | tRES2 | 30 | us | 119 | |||
| Write Status/Configuration Register Cycle Time | tW | 40 | ms | 119 | |||
| Byte-Program | tBP | 25 | 60 | us | 119 | ||
| Page Program Cycle Time | tPP | 0.25 | 0.75 | ms | 119 | ||
| Sector Erase Cycle Time | tSE | 30 | 400 | ms | 120 | ||
| Block Erase (32KB) Cycle Time | tBE32 | 150 | 1000 | ms | 120 | ||
| Block Erase (64KB) Cycle Time | tBE | 280 | 2000 | ms | 120 | ||
| Chip Erase Cycle Time | tCE | 140 | 200 | s | 120 | ||
| Erase Suspend Latency | tESL | 25 | us | 120 | |||
| Latency between Program Resume and next Suspend | tPRS | 0.3 | 100 | us | 120 | ||
| Latency between Erase Resume and next Suspend | tERS | 0.3 | 400 | us | 120 | ||
| Ambient Operating Temperature (Industrial grade) | -40 | 85 | °C | 116 | |||
| Storage Temperature | -65 | 150 | °C | 116 | |||
| Applied Input Voltage | -0.5 | V | 116 | ||||
| Applied Output Voltage | -0.5 | V | 116 | ||||
| VCC to Ground Potential | VCC | -0.5 | 4 | V | 116 | ||
| Input voltage with respect to GND on all power pins, SI, CS# | -1 | V | 125 | ||||
| Latch-up current | -100 | 100 | mA | VCC = 3.0V, one pin at a time; includes all pins except VCC | 125 | ||
| Supply Voltage VCC | VCC | 2.7 | 3.6 | V | For read, erase, and program operations | 5 | |
| VCC Rise Time | tVR | 500000 | us/V | 121 |
CAD (KiCad official)
- Symbol:
MX25L51245GMI-08G - Footprint:
Package_SO:SOIC-16W_7.5x12.8mm_P1.27mm - 3D model: SOP-16-300mil (KiCad packages3D, STEP)
- 3D model files:
mx25l51245gmi-08g-etched.step/mx25l51245gmi-08g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mx25l51245gmi-08g.step/mx25l51245gmi-08g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MXIC(Macronix) datasheet (132 pp, sha256
ed7c88a4e13343cf, retrieved 2026-11-13, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MX25L51245GMI-08G
**MXIC(Macronix)** · NOR FLASH · SOP-16-300mil
MX25L51245GMI-08G from MXIC(Macronix), in a SOP-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC/SIO3 | bidirectional | No connection in single and dual I/O operation; becomes serial data input and output SIO3 in 4 x I/O read mode. |
| 2 | VCC | power_in | Power supply pin (+3V); the DC and AC characteristics are specified for VCC = 2.7V to 3.6V. |
| 3 | RESET# | input | Hardware reset input, active low; the internal pull-up stays active only while the pin is not physically connected in the system. |
| 4 | NC | unconnected | No connection. |
| 5 | DNU | unconnected | Do Not Use; it may connect to an internal signal inside the device, so leave it unconnected. |
| 6 | DNU | unconnected | Do Not Use; it may connect to an internal signal inside the device, so leave it unconnected. |
| 7 | CS# | input | Chip select input, active low; serial access to the device is enabled while CS# is low. |
| 8 | SO/SIO1 | bidirectional | Serial data output in single I/O mode; serial data input and output SIO1 in 2 x I/O or 4 x I/O read mode. |
| 9 | WP#/SIO2 | bidirectional | Write protection input, active low, or serial data input and output SIO2 in 4 x I/O read mode; the internal pull-up stays active only while the pin is not physically connected. |
| 10 | GND | power_in | Ground reference. |
| 11 | DNU | unconnected | Do Not Use; it may connect to an internal signal inside the device, so leave it unconnected. |
| 12 | DNU | unconnected | Do Not Use; it may connect to an internal signal inside the device, so leave it unconnected. |
| 13 | NC | unconnected | No connection. |
| 14 | NC | unconnected | No connection. |
| 15 | SI/SIO0 | bidirectional | Serial data input in single I/O mode; serial data input and output SIO0 in 2 x I/O or 4 x I/O read mode. |
| 16 | SCLK | input | Clock input for the serial interface. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MXIC(Macronix) |
| Package | SOP-16-300mil |
| Category | Memory |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Load Current | ILI | -2 | | 2 | uA | VCC = VCC Max, VIN = VCC or GND | 118 |
| Output Leakage Current | ILO | -2 | | 2 | uA | VCC = VCC Max, VOUT = VCC or GND | 118 |
| VCC Standby Current | ISB1 | | 20 | 100 | uA | VIN = VCC or GND, CS# = VCC | 118 |
| Deep Power-down Current | ISB2 | | | 20 | uA | VIN = VCC or GND, CS# = VCC | 118 |
| VCC Read current (DTR 4 x I/O read, 100MHz) | ICC1 | | | 30 | mA | f=100MHz, (DTR 4 x I/O read), SCLK=0.1VCC/0.9VCC, SO=Open | 118 |
| VCC Read current (4 x I/O read, 104MHz) | ICC1 | | | 20 | mA | f=104MHz, (4 x I/O read), SCLK=0.1VCC/0.9VCC, SO=Open | 118 |
| VCC Read current (84MHz) | ICC1 | | | 15 | mA | f=84MHz, SCLK=0.1VCC/0.9VCC, SO=Open | 118 |
| VCC Program Current (PP) | ICC2 | | 20 | 25 | mA | Program in Progress, CS# = VCC | 118 |
| VCC Write Status Register (WRSR) Current | ICC3 | | | 20 | mA | Program status register in progress, CS#=VCC | 118 |
| VCC Sector/Block (32K, 64K) Erase Current (SE/BE/BE32K) | ICC4 | | 20 | 25 | mA | Erase in Progress, CS#=VCC | 118 |
| VCC Chip Erase Current (CE) | ICC5 | | 20 | 25 | mA | Erase in Progress, CS#=VCC | 118 |
| Input Low Voltage | VIL | -0.5 | | 0.8 | V | | 118 |
| Output Low Voltage | VOL | | | 0.2 | V | IOL = 100uA | 118 |
| Clock Frequency for all commands (except Read Operation) | fSCLK | | | 166 | MHz | Clock frequency for all commands except Read Operation | 119 |
| Clock Frequency for READ instructions | fRSCLK | | | 66 | MHz | Clock Frequency for READ instructions | 119 |
| Clock High Time | tCH | 7 | | | ns | <= 66MHz (fSCLK) | 119 |
| Clock Low Time | tCL | 7 | | | ns | <= 66MHz (fSCLK) | 119 |
| Clock Rise Time (peak to peak) | tCLCH | 0.1 | | | V/ns | peak to peak | 119 |
| Clock Fall Time (peak to peak) | tCHCL | 0.1 | | | V/ns | peak to peak | 119 |
| CS# Active Setup Time (relative to SCLK) | tSLCH | 3 | | | ns | | 119 |
| CS# Not Active Hold Time (relative to SCLK) | tCHSL | 4 | | | ns | | 119 |
| Data In Setup Time | tDVCH | 2 | | | ns | | 119 |
| Data In Hold Time | tCHDX | 2 | | | ns | VCC: 2.7V - 3.6V | 119 |
| Data In Hold Time | tCHDX | 1 | | | ns | VCC: 3.0V - 3.6V (Loading: 15pF/10pF) | 119 |
| CS# Active Hold Time (relative to SCLK) | tCHSH | 3 | | | ns | | 119 |
| CS# Not Active Setup Time (relative to SCLK) | tSHCH | 3 | | | ns | | 119 |
| CS# Deselect Time | tSHSL | 7 | | | ns | From Read to next Read | 119 |
| CS# Deselect Time | tSHSL | 30 | | | ns | From Write/Erase/Program to Read Status Register | 119 |
| Output Disable Time | tSHQZ | | | 8 | ns | | 119 |
| Clock Low to Output Valid | tCLQV | | | 8 | ns | VCC: 2.7V - 3.6V, Loading: 30pF | 119 |
| Clock Low to Output Valid | tCLQV | | | 6 | ns | VCC: 2.7V - 3.6V, Loading: 15pF | 119 |
| Clock Low to Output Valid | tCLQV | | | 5 | ns | VCC: 2.7V - 3.6V, Loading: 10pF | 119 |
| Clock Low to Output Valid | tCLQV | | | 4.5 | ns | VCC: 3.0V - 3.6V, Loading: 10pF, ODS (1,1,0) | 119 |
| Output Hold Time | tCLQX | 1 | | | ns | Loading: 30pF | 119 |
| Write Protect Setup Time | tWHSL | 20 | | | ns | | 119 |
| Write Protect Hold Time | tSHWL | 100 | | | ns | | 119 |
| CS# High to Deep Power-down Mode | tDP | | | 10 | us | | 119 |
| CS# High to Standby Mode with Electronic Signature Read | tRES2 | | | 30 | us | | 119 |
| Write Status/Configuration Register Cycle Time | tW | | | 40 | ms | | 119 |
| Byte-Program | tBP | | 25 | 60 | us | | 119 |
| Page Program Cycle Time | tPP | | 0.25 | 0.75 | ms | | 119 |
| Sector Erase Cycle Time | tSE | | 30 | 400 | ms | | 120 |
| Block Erase (32KB) Cycle Time | tBE32 | | 150 | 1000 | ms | | 120 |
| Block Erase (64KB) Cycle Time | tBE | | 280 | 2000 | ms | | 120 |
| Chip Erase Cycle Time | tCE | | 140 | 200 | s | | 120 |
| Erase Suspend Latency | tESL | | | 25 | us | | 120 |
| Latency between Program Resume and next Suspend | tPRS | | 0.3 | 100 | us | | 120 |
| Latency between Erase Resume and next Suspend | tERS | | 0.3 | 400 | us | | 120 |
| Ambient Operating Temperature (Industrial grade) | | -40 | | 85 | °C | | 116 |
| Storage Temperature | | -65 | | 150 | °C | | 116 |
| Applied Input Voltage | | -0.5 | | | V | | 116 |
| Applied Output Voltage | | -0.5 | | | V | | 116 |
| VCC to Ground Potential | VCC | -0.5 | | 4 | V | | 116 |
| Input voltage with respect to GND on all power pins, SI, CS# | | -1 | | | V | | 125 |
| Latch-up current | | -100 | | 100 | mA | VCC = 3.0V, one pin at a time; includes all pins except VCC | 125 |
| Supply Voltage VCC | VCC | 2.7 | | 3.6 | V | For read, erase, and program operations | 5 |
| VCC Rise Time | tVR | | | 500000 | us/V | | 121 |
## CAD (KiCad official)
- Symbol: `MX25L51245GMI-08G`
- Footprint: `Package_SO:SOIC-16W_7.5x12.8mm_P1.27mm`
- 3D model: SOP-16-300mil (KiCad packages3D, STEP)
- 3D model files: `mx25l51245gmi-08g-etched.step` / `mx25l51245gmi-08g-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mx25l51245gmi-08g.step` / `mx25l51245gmi-08g.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [MXIC(Macronix) datasheet](docs/mx25l51245gmi-08g-datasheet.pdf) (132 pp, sha256 `ed7c88a4e13343cf`, retrieved 2026-11-13, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mx25l51245gmi-08g-datasheet.pdf)