Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MX25L51245GMI-08G

MXIC(Macronix) · NOR FLASH · SOP-16-300mil

MX25L51245GMI-08G from MXIC(Macronix), in a SOP-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC/SIO3 bidirectional No connection in single and dual I/O operation; becomes serial data input and output SIO3 in 4 x I/O read mode.
2 VCC power_in Power supply pin (+3V); the DC and AC characteristics are specified for VCC = 2.7V to 3.6V.
3 RESET# input Hardware reset input, active low; the internal pull-up stays active only while the pin is not physically connected in the system.
4 NC unconnected No connection.
5 DNU unconnected Do Not Use; it may connect to an internal signal inside the device, so leave it unconnected.
6 DNU unconnected Do Not Use; it may connect to an internal signal inside the device, so leave it unconnected.
7 CS# input Chip select input, active low; serial access to the device is enabled while CS# is low.
8 SO/SIO1 bidirectional Serial data output in single I/O mode; serial data input and output SIO1 in 2 x I/O or 4 x I/O read mode.
9 WP#/SIO2 bidirectional Write protection input, active low, or serial data input and output SIO2 in 4 x I/O read mode; the internal pull-up stays active only while the pin is not physically connected.
10 GND power_in Ground reference.
11 DNU unconnected Do Not Use; it may connect to an internal signal inside the device, so leave it unconnected.
12 DNU unconnected Do Not Use; it may connect to an internal signal inside the device, so leave it unconnected.
13 NC unconnected No connection.
14 NC unconnected No connection.
15 SI/SIO0 bidirectional Serial data input in single I/O mode; serial data input and output SIO0 in 2 x I/O or 4 x I/O read mode.
16 SCLK input Clock input for the serial interface.

Key specifications

Parameter Value
Manufacturer MXIC(Macronix)
Package SOP-16-300mil
Category Memory
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Load Current ILI -2 2 uA VCC = VCC Max, VIN = VCC or GND 118
Output Leakage Current ILO -2 2 uA VCC = VCC Max, VOUT = VCC or GND 118
VCC Standby Current ISB1 20 100 uA VIN = VCC or GND, CS# = VCC 118
Deep Power-down Current ISB2 20 uA VIN = VCC or GND, CS# = VCC 118
VCC Read current (DTR 4 x I/O read, 100MHz) ICC1 30 mA f=100MHz, (DTR 4 x I/O read), SCLK=0.1VCC/0.9VCC, SO=Open 118
VCC Read current (4 x I/O read, 104MHz) ICC1 20 mA f=104MHz, (4 x I/O read), SCLK=0.1VCC/0.9VCC, SO=Open 118
VCC Read current (84MHz) ICC1 15 mA f=84MHz, SCLK=0.1VCC/0.9VCC, SO=Open 118
VCC Program Current (PP) ICC2 20 25 mA Program in Progress, CS# = VCC 118
VCC Write Status Register (WRSR) Current ICC3 20 mA Program status register in progress, CS#=VCC 118
VCC Sector/Block (32K, 64K) Erase Current (SE/BE/BE32K) ICC4 20 25 mA Erase in Progress, CS#=VCC 118
VCC Chip Erase Current (CE) ICC5 20 25 mA Erase in Progress, CS#=VCC 118
Input Low Voltage VIL -0.5 0.8 V 118
Output Low Voltage VOL 0.2 V IOL = 100uA 118
Clock Frequency for all commands (except Read Operation) fSCLK 166 MHz Clock frequency for all commands except Read Operation 119
Clock Frequency for READ instructions fRSCLK 66 MHz Clock Frequency for READ instructions 119
Clock High Time tCH 7 ns <= 66MHz (fSCLK) 119
Clock Low Time tCL 7 ns <= 66MHz (fSCLK) 119
Clock Rise Time (peak to peak) tCLCH 0.1 V/ns peak to peak 119
Clock Fall Time (peak to peak) tCHCL 0.1 V/ns peak to peak 119
CS# Active Setup Time (relative to SCLK) tSLCH 3 ns 119
CS# Not Active Hold Time (relative to SCLK) tCHSL 4 ns 119
Data In Setup Time tDVCH 2 ns 119
Data In Hold Time tCHDX 2 ns VCC: 2.7V - 3.6V 119
Data In Hold Time tCHDX 1 ns VCC: 3.0V - 3.6V (Loading: 15pF/10pF) 119
CS# Active Hold Time (relative to SCLK) tCHSH 3 ns 119
CS# Not Active Setup Time (relative to SCLK) tSHCH 3 ns 119
CS# Deselect Time tSHSL 7 ns From Read to next Read 119
CS# Deselect Time tSHSL 30 ns From Write/Erase/Program to Read Status Register 119
Output Disable Time tSHQZ 8 ns 119
Clock Low to Output Valid tCLQV 8 ns VCC: 2.7V - 3.6V, Loading: 30pF 119
Clock Low to Output Valid tCLQV 6 ns VCC: 2.7V - 3.6V, Loading: 15pF 119
Clock Low to Output Valid tCLQV 5 ns VCC: 2.7V - 3.6V, Loading: 10pF 119
Clock Low to Output Valid tCLQV 4.5 ns VCC: 3.0V - 3.6V, Loading: 10pF, ODS (1,1,0) 119
Output Hold Time tCLQX 1 ns Loading: 30pF 119
Write Protect Setup Time tWHSL 20 ns 119
Write Protect Hold Time tSHWL 100 ns 119
CS# High to Deep Power-down Mode tDP 10 us 119
CS# High to Standby Mode with Electronic Signature Read tRES2 30 us 119
Write Status/Configuration Register Cycle Time tW 40 ms 119
Byte-Program tBP 25 60 us 119
Page Program Cycle Time tPP 0.25 0.75 ms 119
Sector Erase Cycle Time tSE 30 400 ms 120
Block Erase (32KB) Cycle Time tBE32 150 1000 ms 120
Block Erase (64KB) Cycle Time tBE 280 2000 ms 120
Chip Erase Cycle Time tCE 140 200 s 120
Erase Suspend Latency tESL 25 us 120
Latency between Program Resume and next Suspend tPRS 0.3 100 us 120
Latency between Erase Resume and next Suspend tERS 0.3 400 us 120
Ambient Operating Temperature (Industrial grade) -40 85 °C 116
Storage Temperature -65 150 °C 116
Applied Input Voltage -0.5 V 116
Applied Output Voltage -0.5 V 116
VCC to Ground Potential VCC -0.5 4 V 116
Input voltage with respect to GND on all power pins, SI, CS# -1 V 125
Latch-up current -100 100 mA VCC = 3.0V, one pin at a time; includes all pins except VCC 125
Supply Voltage VCC VCC 2.7 3.6 V For read, erase, and program operations 5
VCC Rise Time tVR 500000 us/V 121

CAD (KiCad official)

  • Symbol: MX25L51245GMI-08G
  • Footprint: Package_SO:SOIC-16W_7.5x12.8mm_P1.27mm
  • 3D model: SOP-16-300mil (KiCad packages3D, STEP)
  • 3D model files: mx25l51245gmi-08g-etched.step / mx25l51245gmi-08g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mx25l51245gmi-08g.step / mx25l51245gmi-08g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: MXIC(Macronix) datasheet (132 pp, sha256 ed7c88a4e13343cf, retrieved 2026-11-13, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF