main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers mt9523ct-10bf3: viewers · Ray
mt9523ct-10bf3-etched.glb Publish 0.1.0 · Ray
mt9523ct-10bf3-etched.step mt9523ct-10bf3: factory component page (tier=lcsc) · Ray
mt9523ct-10bf3-hero.glb mt9523ct-10bf3: hero GLB from the etched model (keeps the MPN mark) · Ray
mt9523ct-10bf3-hero.overlay.json Publish 0.1.0 · Ray
mt9523ct-10bf3.glb Publish 0.1.0 · Ray
mt9523ct-10bf3.kicad_mod Publish 0.1.0 · Ray
mt9523ct-10bf3.kicad_sym Publish 0.1.0 · Ray
mt9523ct-10bf3.lbr Publish 0.1.0 · Ray
mt9523ct-10bf3.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier lcsc, 8 pins · Ray

MT9523CT-10BF3

Magn Tek · Current Sensors · SOP-8

MT9523CT-10BF3 from Magn Tek, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IP+ passive Input current positive terminal of the internal low-resistance (typically 1.0mΩ) conductor path, which is electrically isolated from the signal pins 5 to 8 with 2.5kVrms isolation for 1 minute.
2 IP+ passive Input current positive terminal, bonded in parallel with pin 1 to the internal conductor path that runs to pins 3 and 4, with the same 2.5kVrms isolation from the signal pins.
3 IP- passive Input current negative terminal of the internal conductor path, which carries the measured current from pins 1 and 2 and is isolated from the signal pins 5 to 8.
4 IP- passive Input current negative terminal, bonded in parallel with pin 3 to the internal conductor path that carries the measured current from pins 1 and 2.
5 GND power_in Signal ground for the Hall sensor and output stage, referenced for the VOUT and VZCR outputs.
6 VZCR output Zero-current reference voltage output, which is ratiometric to VCC (2.5V at VCC=5V) for proportional-output parts or fixed (2.5V for bidirectional 5V-fixed parts, 1.65V for 3.3V-fixed parts) for fixed-output parts, and is used with VOUT to measure zero-current offset single-ended or differentially.
7 VOUT output Analog voltage output that is proportional to the input current, with zero-current output of 0.5×VCC for bidirectional proportional parts or 2.5V for bidirectional fixed-output parts.
8 VCC power_in Supply voltage input, specified for 5.0V or 3.3V DC supply operation, with minimum operating VCC of 2.5V stated in the power-up timing definition.

Key specifications

Parameter Value
Manufacturer Magn Tek
Package SOP-8
Category Magnetic Sensors
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
电源电压 (supply voltage) VCC 3 3.3 3.6 V XXBR3, XXBF3 8
消耗电流 (supply current) ICC 13 20 mA VCC=3.3V, TA=25°C 8
模拟输出低电平 (analog output low) VOL 0.3 V RL>=4.7KΩ 8
输出电阻负载 下拉到GND (output load pull-down) RL 4.7 KΩ 下拉到GND 8
输出电阻负载 上拉到VCC (output load pull-up) RL 4.7 KΩ 上拉到VCC 8
输出电容负载 (output capacitive load) CL 0.47 1 nF OUT to GND 8
参考端电阻负载 下拉到GND (reference load pull-down) RL_ZCR 4.7 KΩ 下拉到GND 9
参考端电阻负载 上拉到VCC (reference load pull-up) RL_ZCR 4.7 KΩ 上拉到VCC 9
参考端电容负载 (reference capacitive load) CL_ZCR 0.47 1 nF VZCR to GND 9
非线性误差 (nonlinearity error) ELIN -1 0.3 1 %F.S. Full Scale 9
霍尔盘灵敏度匹配 (Hall plate sensitivity match) SNST(match) -1 1 % TA=25°C 9
老化引起的灵敏度误差漂移 (sensitivity drift over life) ESNST_DRIFT -3 3 % TA=-40~150℃ 7
老化引起的总输出误差漂移 (total output error drift over life) ETOT_DRIFT -3 3 % TA=-40~150℃ 7
电源电压 (absolute max supply voltage) VCC 6 V 7
电源反向电压 (reverse supply voltage) VRCC -0.1 V 7
输出反向电压 (reverse output voltage) VROUT -0.1 V 7
持续输出电流 源电流 (continuous output source current) IOUT(source) 40 mA 7
持续输出电流 灌电流 (continuous output sink current) IOUT(sink) 40 mA 7
工作环境温度 (operating ambient temperature) TA -40 150 ℃ 7
存储温度 (storage temperature) TS -50 150 ℃ 7
结温 (junction temperature) TJ 165 ℃ 7
输入电流范围 (input current range) IPR -10 10 A 21
参考输出误差 (reference output error) VOE_ZCR -10 10 mV TA=25°C 21
参考输出误差 (reference output error) VOE_ZCR -20 20 mV TA=-40°C to 25°C 21
零电流输出误差 VOQ-VZCR (zero-current output error) VOE -5 5 mV IP=0 A, TA=25°C 21
零电流输出误差 VOQ-VZCR (zero-current output error) VOE -20 20 mV IP=0 A, TA=-40°C to 25°C 21
零电流输出误差 VOQ-VZCR (zero-current output error) VOE -15 15 mV IP=0 A, TA=25°C to 150°C 21
灵敏度误差 (sensitivity error) ESNST -1 1 % IP=10A, TA=25°C 21
灵敏度误差 (sensitivity error) ESNST -2.5 2.5 % IP=10A, TA=-40°C to 25°C 21
灵敏度误差 (sensitivity error) ESNST -2.2 2.2 % IP=10A, TA=25°C to 150°C 21
总输出误差 (total output error) ETOT -1.5 1.5 % IP=10A, TA=25°C 21
总输出误差 (total output error) ETOT -3.3 3.3 % IP=10A, TA=-40°C to 25°C 21
总输出误差 (total output error) ETOT -2.8 2.8 % IP=10A, TA=25°C to 150°C 21

CAD (KiCad official)

  • Symbol: MT9523CT-10BF3
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOP-8 (KiCad packages3D, STEP)
  • 3D model files: mt9523ct-10bf3-etched.step / mt9523ct-10bf3-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mt9523ct-10bf3.step / mt9523ct-10bf3.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Magn Tek datasheet (35 pp, sha256 47ac41e92a15e700, retrieved 2026-11-05, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF