main
History Download
Ray Publish 0.1.0 351a448

MT6826SGT-STD

MagnTek(麦歌恩) · IC · TSSOP-16

MT6826SGT-STD from MagnTek(麦歌恩), in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 U output Incremental U signal or -A signal output, selected by the UVW_MUX register; default is UVW mode with 2 to 16 pole pairs per revolution programmable.
2 V power_in Incremental V signal or -B signal output, selected by the UVW_MUX register; default is UVW mode with 120° phase spacing.
3 W output Incremental W signal or -Z signal output, selected by the UVW_MUX register; default is UVW mode with 120° phase spacing.
4 CAL_EN input Client self-calibration enable pin; raising it from low to high while the system runs at constant speed starts self-calibration, and it has an internal 250KΩ pull-down.
5 MISO output SPI data bus carrying data from the MT6826S to the host; it stays high-impedance when not outputting.
6 MOSI input SPI data bus carrying data from the host into the MT6826S.
7 SCK input SPI clock input from the host, supporting up to 16 MHz, held high when no communication is active.
8 CSN input SPI chip-select input; a falling edge starts SPI communication and a rising edge ends it.
9 VDD power_in Supply pin for 3.3 V to 5.0 V; the datasheet recommends at least a 0.1 µF decoupling capacitor between VDD and VSS and a TVS diode for EMC.
10 OUT output Single-wire 12-bit absolute angle PWM output (994 Hz or 497 Hz selectable), with output level polarity set by PWM_POL.
11 TEST input Factory test pin reserved for MagnTek use only and not to be used by customers; it has an internal 250KΩ pull-down.
12 VSS power_in Ground pin for the device.
13 TEST_EN input Factory test enable pin reserved for MagnTek use only; it has an internal 250KΩ pull-down.
14 Z output Incremental Z (zero-position) index output, one pulse per revolution with programmable width and phase.
15 B output Incremental B quadrature output, programmable from 1 to 4,096 pulses per revolution.
16 A output Incremental A quadrature output, programmable from 1 to 4,096 pulses per revolution.

Key specifications

Parameter Value
Manufacturer MagnTek(麦歌恩)
Package TSSOP-16
Category
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
电源电压 -0.5 6.5 V 8
管脚输入电压范围 -0.5 V max VDD (printed as VDD) 8
管脚输出电流 -20 20 mA ABZ, UVW, OUT, MISO pins 8
存储温度 -40 150 ℃ 8
防闩锁能力(闩锁输入电流) -100 100 mA AEC-Q100-004 8
静电防护能力(人体放电模式) -8 8 kV AEC-Q100-002 8
静电防护能力(元件充电模式) -1.5 1.5 kV AEC-Q100-011 8
电源电压 3 5.5 V 8
磁场强度 30 1000 mT measured on chip surface 8
转速 120000 RPM 8
工作温度 -40 125 ℃ 8
VDD 电源电压 VDD 3 5.5 V - 9
Idd 芯片工作电流 Idd 15 22 28 mA - 9
出厂校准后的积分非线性 INL -1 1 ° 注释[1] 9
客户端自校准后的积分非线性 INL -0.1 0.1 ° 注释[2] 9
差分非线性(图-4) DNL -0.005 0.005 ° @2500脉冲ABZ模式 9
PWM频率 FPWM -8 8 % 可编程 10
上升沿时间 TRise 1 us 负载CL=1nF 10
下降沿时间 TFall 1 us 负载CL=1nF 10
AB分辨率 1 4096 脉冲/圈 可编程 10
A或B频率 ABFreq 2.048 MHz 注释[3] 10
EEPROM 擦写和读取时的供电电压 VDD 3 5.5 V 擦写和读取时 10
EEPROM 数据保存时间 10 年 @150℃ 10
VOL 数字I/O输出逻辑低电平 VOL 0.4 V 推挽输出 @Iout=2mA 11
上升沿时间(数字I/O) TRise 50 ns CL=20pf 11
下降沿时间(数字I/O) TFall 50 ns CL=20pf 11
输入磁场大小(平行于芯片表面的水平方向) Bpk 30 1000 mT 在芯片表面测得的 12
间隙 AG 1 3 mm 芯片表面和磁铁的距离 12
偏心 DISP 0.3 mm 磁体中心和芯片感应中心的偏差 12
CSN下降沿到第一个时钟SCK下降沿的延时 TL 100 ns 24
时钟周期 TSCK 64 ns 24
时钟低电平时间 TSCKL 30 ns 24
时钟高电平时间 TSCKH 30 ns 24
MISO数据等待时间 TDV 15 ns 有20pf的电容负载 24
MOSI数据建立时间 TST 10 ns 24
MOSI数据保持时间 THD 10 ns 24
芯片开始正常工作到A或B脉冲第一个上升沿延时 T1 450 500 550 us 31
A、B脉冲串输出绝对角度信息的时间 T2 30 ms @BW≥3 31
AB脉冲最小宽度 T3 0.9 us 31

CAD (KiCad official)

  • Symbol: MT6826SGT-STD
  • Footprint: Package_SO:TSSOP-16_4.4x5mm_P0.65mm
  • 3D model: TSSOP-16 (KiCad packages3D, STEP)
  • 3D model files: mt6826sgt-std-etched.step / mt6826sgt-std-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mt6826sgt-std.step / mt6826sgt-std.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: MagnTek(麦歌恩) datasheet, copy hosted by LCSC (47 pp, sha256 f3b282a641a223e9, retrieved 2026-11-19)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF