Generated by kicad-footprint-generator · KiCad file format 20260206
MT6826SGT-STD
MagnTek(麦歌恩) · IC · TSSOP-16
MT6826SGT-STD from MagnTek(麦歌恩), in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | U | output | Incremental U signal or -A signal output, selected by the UVW_MUX register; default is UVW mode with 2 to 16 pole pairs per revolution programmable. |
| 2 | V | power_in | Incremental V signal or -B signal output, selected by the UVW_MUX register; default is UVW mode with 120° phase spacing. |
| 3 | W | output | Incremental W signal or -Z signal output, selected by the UVW_MUX register; default is UVW mode with 120° phase spacing. |
| 4 | CAL_EN | input | Client self-calibration enable pin; raising it from low to high while the system runs at constant speed starts self-calibration, and it has an internal 250KΩ pull-down. |
| 5 | MISO | output | SPI data bus carrying data from the MT6826S to the host; it stays high-impedance when not outputting. |
| 6 | MOSI | input | SPI data bus carrying data from the host into the MT6826S. |
| 7 | SCK | input | SPI clock input from the host, supporting up to 16 MHz, held high when no communication is active. |
| 8 | CSN | input | SPI chip-select input; a falling edge starts SPI communication and a rising edge ends it. |
| 9 | VDD | power_in | Supply pin for 3.3 V to 5.0 V; the datasheet recommends at least a 0.1 µF decoupling capacitor between VDD and VSS and a TVS diode for EMC. |
| 10 | OUT | output | Single-wire 12-bit absolute angle PWM output (994 Hz or 497 Hz selectable), with output level polarity set by PWM_POL. |
| 11 | TEST | input | Factory test pin reserved for MagnTek use only and not to be used by customers; it has an internal 250KΩ pull-down. |
| 12 | VSS | power_in | Ground pin for the device. |
| 13 | TEST_EN | input | Factory test enable pin reserved for MagnTek use only; it has an internal 250KΩ pull-down. |
| 14 | Z | output | Incremental Z (zero-position) index output, one pulse per revolution with programmable width and phase. |
| 15 | B | output | Incremental B quadrature output, programmable from 1 to 4,096 pulses per revolution. |
| 16 | A | output | Incremental A quadrature output, programmable from 1 to 4,096 pulses per revolution. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MagnTek(麦歌恩) |
| Package | TSSOP-16 |
| Category | |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 电源电压 | -0.5 | 6.5 | V | 8 | |||
| 管脚输入电压范围 | -0.5 | V | max VDD (printed as VDD) | 8 | |||
| 管脚输出电流 | -20 | 20 | mA | ABZ, UVW, OUT, MISO pins | 8 | ||
| 存储温度 | -40 | 150 | ℃ | 8 | |||
| 防闩锁能力(闩锁输入电流) | -100 | 100 | mA | AEC-Q100-004 | 8 | ||
| 静电防护能力(人体放电模式) | -8 | 8 | kV | AEC-Q100-002 | 8 | ||
| 静电防护能力(元件充电模式) | -1.5 | 1.5 | kV | AEC-Q100-011 | 8 | ||
| 电源电压 | 3 | 5.5 | V | 8 | |||
| 磁场强度 | 30 | 1000 | mT | measured on chip surface | 8 | ||
| 转速 | 120000 | RPM | 8 | ||||
| 工作温度 | -40 | 125 | ℃ | 8 | |||
| VDD 电源电压 | VDD | 3 | 5.5 | V | - | 9 | |
| Idd 芯片工作电流 | Idd | 15 | 22 | 28 | mA | - | 9 |
| 出厂校准后的积分非线性 | INL | -1 | 1 | ° | 注释[1] | 9 | |
| 客户端自校准后的积分非线性 | INL | -0.1 | 0.1 | ° | 注释[2] | 9 | |
| 差分非线性(图-4) | DNL | -0.005 | 0.005 | ° | @2500脉冲ABZ模式 | 9 | |
| PWM频率 | FPWM | -8 | 8 | % | 可编程 | 10 | |
| 上升沿时间 | TRise | 1 | us | 负载CL=1nF | 10 | ||
| 下降沿时间 | TFall | 1 | us | 负载CL=1nF | 10 | ||
| AB分辨率 | 1 | 4096 | 脉冲/圈 | 可编程 | 10 | ||
| A或B频率 | ABFreq | 2.048 | MHz | 注释[3] | 10 | ||
| EEPROM 擦写和读取时的供电电压 | VDD | 3 | 5.5 | V | 擦写和读取时 | 10 | |
| EEPROM 数据保存时间 | 10 | 年 | @150℃ | 10 | |||
| VOL 数字I/O输出逻辑低电平 | VOL | 0.4 | V | 推挽输出 @Iout=2mA | 11 | ||
| 上升沿时间(数字I/O) | TRise | 50 | ns | CL=20pf | 11 | ||
| 下降沿时间(数字I/O) | TFall | 50 | ns | CL=20pf | 11 | ||
| 输入磁场大小(平行于芯片表面的水平方向) | Bpk | 30 | 1000 | mT | 在芯片表面测得的 | 12 | |
| 间隙 | AG | 1 | 3 | mm | 芯片表面和磁铁的距离 | 12 | |
| 偏心 | DISP | 0.3 | mm | 磁体中心和芯片感应中心的偏差 | 12 | ||
| CSN下降沿到第一个时钟SCK下降沿的延时 | TL | 100 | ns | 24 | |||
| 时钟周期 | TSCK | 64 | ns | 24 | |||
| 时钟低电平时间 | TSCKL | 30 | ns | 24 | |||
| 时钟高电平时间 | TSCKH | 30 | ns | 24 | |||
| MISO数据等待时间 | TDV | 15 | ns | 有20pf的电容负载 | 24 | ||
| MOSI数据建立时间 | TST | 10 | ns | 24 | |||
| MOSI数据保持时间 | THD | 10 | ns | 24 | |||
| 芯片开始正常工作到A或B脉冲第一个上升沿延时 | T1 | 450 | 500 | 550 | us | 31 | |
| A、B脉冲串输出绝对角度信息的时间 | T2 | 30 | ms | @BW≥3 | 31 | ||
| AB脉冲最小宽度 | T3 | 0.9 | us | 31 |
CAD (KiCad official)
- Symbol:
MT6826SGT-STD - Footprint:
Package_SO:TSSOP-16_4.4x5mm_P0.65mm - 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
mt6826sgt-std-etched.step/mt6826sgt-std-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mt6826sgt-std.step/mt6826sgt-std.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MagnTek(麦歌恩) datasheet, copy hosted by LCSC (47 pp, sha256
f3b282a641a223e9, retrieved 2026-11-19) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).