main
Ray
Publish 0.1.0
6dfbc4f
MSPM0G1518SRHBR
Texas Instruments · IC · VQFN-32(5x5)
MSPM0G1518SRHBR from Texas Instruments, in a VQFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PA0 | bidirectional | 5V-tolerant open-drain IO (ODIO, 20 mA maximum sink) that needs an external pullup to drive high for I2C or UART use, with UART0_TX, I2C0_SDA, TIMA0_C0 and BSLSDA (non-IOMUX) among its functions. |
| 2 | PA1 | bidirectional | 5V-tolerant open-drain IO (ODIO, 20 mA maximum sink) that needs an external pullup to drive high for I2C or UART use, with UART0_RX, I2C0_SCL, TIMA0_C1 and BSLSCL (non-IOMUX) among its functions. |
| 3 | NRST | input | Active-low reset input that must be pulled high to VDD for the device to start, with a 47 kΩ pullup and 10 nF pulldown recommended in the basic application schematic. |
| 4 | VDD | power_in | Supply voltage input, 1.62 V to 3.6 V, with a 10 µF bulk capacitor and 0.1 µF low-ESR ceramic decoupling capacitor recommended across VDD and VSS. |
| 5 | VSS | power_in | Ground reference for the device, with current out of VSS limited to 100 mA at Tj ≤ 90 °C (80 mA at Tj ≤ 130 °C). |
| 6 | PA2 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, which doubles as the ROSC analog pin for the SYSOSC frequency correction loop (100 kΩ ±0.1% resistor to VSS) and is free for digital IO when that loop is not used. |
| 7 | PA3 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with TIMG8_C0, SPI0_CS1, I2C1_SDA and COMP0_OUT among its functions and LFXIN (32 kHz crystal input) as a non-IOMUX analog function. |
| 8 | PA4 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with SPI0_POCI, I2C1_SCL, LFCLK_IN and UART1_RX among its functions and LFXOUT (32 kHz crystal output) as a non-IOMUX analog function. |
| 9 | PA5 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with SPI0_PICO, I2C1_SDA, UART0_CTS and FCC_IN among its functions and HFXIN (4-48 MHz crystal input) as a non-IOMUX analog function. |
| 10 | PA6 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with SPI0_SCK, I2C1_SCL, HFCLK_IN and UART0_RTS among its functions and HFXOUT (4-48 MHz crystal output) as a non-IOMUX analog function. |
| 11 | PA7 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with COMP0_OUT, CLK_OUT, FCC_IN and SPI0_POCI among its functions. |
| 12 | PA8 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART1_TX, SPI0_CS0, I2C0_SDA, HFCLK_IN and UART0_RTS among its functions. |
| 13 | PA9 | bidirectional | High-speed (HSIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART1_RX, SPI0_PICO, I2C0_SCL, CLK_OUT and RTC_OUT among its functions. |
| 14 | PA10 | bidirectional | High-drive (HDIO) IO with 20 mA maximum current, with UART0_TX, SPI0_POCI, I2C0_SDA, CLK_OUT and SPI2_SCK among its functions and BSLTX (non-IOMUX) and WAKE as additional functions. |
| 15 | PA11 | bidirectional | High-drive (HDIO) IO with 20 mA maximum current, with UART0_RX, SPI0_SCK, I2C0_SCL, COMP0_OUT and TIMA1_C1 among its functions and BSLRX (non-IOMUX) and WAKE as additional functions. |
| 16 | PA12 | bidirectional | High-speed (HSIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART3_CTS, SPI0_SCK, COMP0_OUT, CAN0_TX and UART1_CTS among its functions and A0_8 (ADC0 channel 8) as a non-IOMUX analog function. |
| 17 | PA13 | bidirectional | High-speed (HSIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART3_RTS, SPI0_POCI, UART3_RX, RTC_OUT and CAN0_RX among its functions and A0_9 (ADC0 channel 9) and COMP0_IN2- as non-IOMUX analog functions. |
| 18 | PA14 | bidirectional | High-speed (HSIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART0_CTS, SPI0_PICO, UART3_TX, CLK_OUT and UART7_RX among its functions and A0_12 (ADC0 channel 12) and COMP0_IN2+ as non-IOMUX analog functions. |
| 19 | PA15 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART0_RTS, SPI1_CS2, I2C1_SCL and TIMA1_C0 among its functions, and A1_0 shared with DAC_OUT, where external circuitry on PA15 should be avoided when DAC_OUT is used. |
| 20 | PA16 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with COMP0_OUT, SPI1_POCI, I2C1_SDA, I2C2_SDA and COMP2_OUT among its functions and A1_1 (ADC1 channel 1) as a non-IOMUX analog function. |
| 21 | PA17 | bidirectional | Standard (SDIO) IO with wake capability (6 mA maximum current at VDD ≥ 2.7 V), with UART1_TX, SPI1_SCK, I2C1_SCL and TIMA0_C3 among its functions, and WAKE, A1_2 and COMP0_IN1- as non-IOMUX functions. |
| 22 | PA18 | bidirectional | Standard (SDIO) IO with wake capability (6 mA maximum current at VDD ≥ 2.7 V), with UART1_RX, SPI1_PICO, I2C1_SDA and TIMA0_C3N among its functions, and BSL_invoke, WAKE, A1_3 and COMP0_IN1+ as non-IOMUX functions. |
| 23 | PA19 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with SWDIO (2-pin serial wire debug data), SPI1_POCI, I2C1_SDA and TIMA0_C2 among its functions, and A0_13 (ADC0 channel 13) as a non-IOMUX analog function. |
| 24 | PA20 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with SWCLK (2-pin serial wire debug clock), SPI1_SCK, I2C1_SCL and TIMA0_C2N among its functions, and A0_14 (ADC0 channel 14) as a non-IOMUX analog function. |
| 25 | PA21 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART7_TX, UART1_CTS, SPI1_CS1 and TIMA0_C0 among its functions, and A1_7 (ADC1 channel 7), COMP2_IN1- and VREF- as non-IOMUX analog functions. |
| 26 | PA22 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART7_RX, SPI0_CS2, UART1_RTS, CLK_OUT and I2C0_SCL among its functions, and A0_7 (ADC0 channel 7) as a non-IOMUX analog function. |
| 27 | PA23 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART7_TX, SPI0_CS3, I2C2_SCL and TIMA0_C3 among its functions, and A1_12 (ADC1 channel 12), COMP1_IN1- and VREF+ as non-IOMUX analog functions. |
| 28 | PA24 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART7_RX, SPI0_CS2, I2C2_SDA and TIMA0_C3N among its functions, and A0_3 (ADC0 channel 3) as a non-IOMUX analog function. |
| 29 | PA25 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART3_RX, SPI1_CS3, TIMG12_C1 and UART3_TX among its functions, and A0_2 (ADC0 channel 2) as a non-IOMUX analog function. |
| 30 | PA26 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART3_TX, SPI1_CS0, TIMG8_C0, CAN0_TX and UART3_RX among its functions, and A0_1 (ADC0 channel 1) and COMP0_IN0+ as non-IOMUX analog functions. |
| 31 | PA27 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART3_RX, SPI1_CS1, CLK_OUT, RTC_OUT and CAN0_RX among its functions, and A0_0 (ADC0 channel 0) and COMP0_IN0- as non-IOMUX analog functions. |
| 32 | VCORE | power_out | Internal core-logic supply node that must only be connected to a 470 nF CVCORE capacitor to VSS, with no external voltage or load applied. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-32(5x5) |
| Category | |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage at VDD pin | VDD | -0.3 | 4.1 | V | At VDD pin | 54 | |
| Input voltage applied to 5-V tolerant open-drain pins | VI | -0.3 | 5.5 | V | Applied to any 5-V tolerant open-drain pins | 54 | |
| Input voltage applied to common tolerance pins | VI | -0.3 | 4.1 | V | Applied to any common tolerance pins; printed as VDD + 0.3 (4.1 MAX) | 54 | |
| Current into VDD pin (source) | IVDD | 80 | mA | -40 °C ≤ Tj ≤ 130 °C | 54 | ||
| Current into VDD pin (source) | IVDD | 100 | mA | -40 °C ≤ Tj ≤ 90 °C | 54 | ||
| Current out of VSS pin (sink) | IVSS | 80 | mA | -40 °C ≤ Tj ≤ 130 °C | 54 | ||
| Current out of VSS pin (sink) | IVSS | 100 | mA | -40 °C ≤ Tj ≤ 90 °C | 54 | ||
| Current of SDIO pin | IIO | 6 | mA | Current sunk or sourced by SDIO pin, VDD>=2.7V | 54 | ||
| Current of HSIO pin | IIO | 6 | mA | Current sunk or sourced by HSIO pin, VDD>=2.7V | 54 | ||
| Current of HDIO pin | IIO | 20 | mA | Current sunk or sourced by HDIO pin | 54 | ||
| Current of ODIO pin | IIO | 20 | mA | Current sunk by ODIO pin | 54 | ||
| Supported diode current | ID | -2 | 2 | mA | Diode current at any device pin (excluding Open Drain IO) | 54 | |
| Ambient temperature | TA | -40 | 125 | °C | Ambient temperature | 54 | |
| Junction temperature | TJ | -40 | 130 | °C | Junction temperature | 54 | |
| Storage temperature | Tstg | -40 | 150 | °C | 54 | ||
| Supply voltage | VDD | 1.62 | 3.6 | V | 54 | ||
| Ambient temperature | TA | -40 | 125 | °C | 54 | ||
| Max junction temperature | TJ | 130 | °C | 55 | |||
| MCLK, CPUCLK frequency with 2 flash wait states | fMCLK | 80 | MHz | PD1 bus clock; wait states managed by SYSCTL | 55 | ||
| MCLK, CPUCLK frequency with 1 flash wait state | fMCLK | 48 | MHz | PD1 bus clock; wait states managed by SYSCTL | 55 | ||
| MCLK, CPUCLK frequency with 0 flash wait states | fMCLK | 24 | MHz | PD1 bus clock; wait states managed by SYSCTL | 55 | ||
| ULPCLK frequency | fULPCLK | 40 | MHz | PD0 bus clock | 55 | ||
| Voltage on VCORE pin | VCORE | 1.35 | V | 54 | |||
| Capacitor connected between VDD and VSS | CVDD | 10 | uF | Low-ESR capacitor, tolerance ±20% or better required | 54 | ||
| Capacitor connected between VCORE and VSS | CVCORE | 470 | nF | Low-ESR capacitor, tolerance ±20% or better required | 54 | ||
| Junction-to-ambient thermal resistance (VQFN-32 RHB) | RθJA | 31.3 | °C/W | 56 | |||
| Junction-to-case (top) thermal resistance (VQFN-32 RHB) | RθJC(top) | 22.6 | °C/W | 56 | |||
| Junction-to-board thermal resistance (VQFN-32 RHB) | RθJB | 12.2 | °C/W | 56 | |||
| Junction-to-top characterization parameter (VQFN-32 RHB) | ΨJT | 0.3 | °C/W | 56 | |||
| Junction-to-board characterization parameter (VQFN-32 RHB) | ΨJB | 12.1 | °C/W | 56 | |||
| Junction-to-case (bottom) thermal resistance (VQFN-32 RHB) | RθJC(bot) | 2.8 | °C/W | 56 | |||
| SLEEP mode supply current, MCLK=SYSPLL 80MHz, CPU halted | IDDSLEEP | 4471 | 6678 | uA | VDD=3.3V; MCLK=SYSPLL, SYSPLLREF=SYSOSC, CPU is halted; 125 °C column | 57 | |
| STOP mode supply current, STOP0 | IDDSTOP0 | 467 | 516 | uA | VDD=3.3V; SYSOSC=32MHz, USE4MHZSTOP=0, DISABLESTOP=0; 125 °C column | 57 | |
| STOP mode supply current, STOP1 | IDDSTOP1 | 255 | 298 | uA | VDD=3.3V; SYSOSC=4MHz, USE4MHZSTOP=1, DISABLESTOP=0; 125 °C column | 57 | |
| STOP mode supply current, STOP2 | IDDSTOP2 | 86 | 123 | uA | VDD=3.3V; SYSOSC off, DISABLESTOP=1, ULPCLK=LFCLK 32kHz; 125 °C column | 57 | |
| STANDBY mode supply current, STANDBY0 | IDDSTBY0 | 29 | 105 | uA | VDD=3.3V; LFCLK=LFXT, STOPCLKSTBY=0, RTC enabled; 125 °C column | 58 | |
| Power-on reset voltage level, rising | VPOR+ | 0.95 | 1.3 | 1.59 | V | 58 | |
| Power-on reset voltage level, falling | VPOR- | 0.9 | 1.25 | 1.54 | V | 58 | |
| POR hysteresis | VHYS, POR | 30 | 58 | 74 | mV | 58 | |
| Brown-out reset voltage level 0 (default), cold start rising | VBOR0+, COLD | 1.5 | 1.56 | 1.63 | V | -40 °C ≤ Ta ≤ 25 °C; cold start, rising | 59 |
| Brown-out reset voltage level 0 (default), cold start rising | VBOR0+, COLD | 1.51 | 1.58 | 1.65 | V | 25 °C ≤ Ta ≤ 125 °C; cold start, rising | 59 |
| Brown-out reset voltage level 0, rising | VBOR0+ | 1.56 | 1.59 | 1.62 | V | Rising(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 0, falling | VBOR0- | 1.55 | 1.58 | 1.61 | V | Falling(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 1, rising | VBOR1+ | 2.13 | 2.17 | 2.21 | V | Rising(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 1, falling | VBOR1- | 2.1 | 2.14 | 2.18 | V | Falling(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 2, rising | VBOR2+ | 2.73 | 2.77 | 2.82 | V | Rising(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 2, falling | VBOR2- | 2.7 | 2.74 | 2.79 | V | Falling(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 3, rising | VBOR3+ | 2.88 | 2.96 | 3.04 | V | Rising(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 3, falling | VBOR3- | 2.85 | 2.93 | 3.01 | V | Falling(1); device in RUN, SLEEP or STOP mode | 59 |
| High level input voltage, ODIO | VIH | 2 | 5.5 | V | VDD≥2.7V | 64 | |
| High level input voltage, ODIO | VIH | 5.5 | V | VDD≥1.62V; printed min is 0.7*VDD | 64 | ||
| Low level input voltage, ODIO | VIL | -0.3 | 0.8 | V | VDD≥2.7V | 64 | |
| Low level input voltage, ODIO | VIL | -0.3 | V | VDD≥1.62V; printed max is 0.3*VDD | 64 | ||
| High-Z leakage current, SDIO (all packages except PZ, PN, PM) | Ilkg | 50 | nA | 1.62V ≤ VDD ≤ 3.6V, -40 °C ≤ Ta ≤ 125 °C | 64 | ||
| Low level output voltage, SDIO | VOL | 0.45 | V | VDD≥2.7V, /IIO/max=6mA; -40 °C ≤ Ta ≤ 125 °C | 65 | ||
| Low level output voltage, HSIO | VOL | 0.45 | V | VDD≥2.7V, DRV=1, /IIO/max=6mA; -40 °C ≤ Ta ≤ 125 °C | 65 | ||
| Low level output voltage, HDIO | VOL | 0.4 | V | VDD≥2.7V, DRV=1(5), /IIO/max=20mA | 65 | ||
| Low level output voltage, ODIO | VOL | 0.45 | V | VDD≥2.7V, IOL,max=8mA; -40 °C ≤ Ta ≤ 125 °C | 65 |
CAD (KiCad official)
- Symbol:
MSPM0G1518SRHBR - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: VQFN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
mspm0g1518srhbr-etched.step/mspm0g1518srhbr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mspm0g1518srhbr.step/mspm0g1518srhbr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (162 pp, sha256
a6ce501f275f0727, retrieved 2026-11-04, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MSPM0G1518SRHBR
**Texas Instruments** · IC · VQFN-32(5x5)
MSPM0G1518SRHBR from Texas Instruments, in a VQFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PA0 | bidirectional | 5V-tolerant open-drain IO (ODIO, 20 mA maximum sink) that needs an external pullup to drive high for I2C or UART use, with UART0_TX, I2C0_SDA, TIMA0_C0 and BSLSDA (non-IOMUX) among its functions. |
| 2 | PA1 | bidirectional | 5V-tolerant open-drain IO (ODIO, 20 mA maximum sink) that needs an external pullup to drive high for I2C or UART use, with UART0_RX, I2C0_SCL, TIMA0_C1 and BSLSCL (non-IOMUX) among its functions. |
| 3 | NRST | input | Active-low reset input that must be pulled high to VDD for the device to start, with a 47 kΩ pullup and 10 nF pulldown recommended in the basic application schematic. |
| 4 | VDD | power_in | Supply voltage input, 1.62 V to 3.6 V, with a 10 µF bulk capacitor and 0.1 µF low-ESR ceramic decoupling capacitor recommended across VDD and VSS. |
| 5 | VSS | power_in | Ground reference for the device, with current out of VSS limited to 100 mA at Tj ≤ 90 °C (80 mA at Tj ≤ 130 °C). |
| 6 | PA2 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, which doubles as the ROSC analog pin for the SYSOSC frequency correction loop (100 kΩ ±0.1% resistor to VSS) and is free for digital IO when that loop is not used. |
| 7 | PA3 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with TIMG8_C0, SPI0_CS1, I2C1_SDA and COMP0_OUT among its functions and LFXIN (32 kHz crystal input) as a non-IOMUX analog function. |
| 8 | PA4 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with SPI0_POCI, I2C1_SCL, LFCLK_IN and UART1_RX among its functions and LFXOUT (32 kHz crystal output) as a non-IOMUX analog function. |
| 9 | PA5 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with SPI0_PICO, I2C1_SDA, UART0_CTS and FCC_IN among its functions and HFXIN (4-48 MHz crystal input) as a non-IOMUX analog function. |
| 10 | PA6 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with SPI0_SCK, I2C1_SCL, HFCLK_IN and UART0_RTS among its functions and HFXOUT (4-48 MHz crystal output) as a non-IOMUX analog function. |
| 11 | PA7 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with COMP0_OUT, CLK_OUT, FCC_IN and SPI0_POCI among its functions. |
| 12 | PA8 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART1_TX, SPI0_CS0, I2C0_SDA, HFCLK_IN and UART0_RTS among its functions. |
| 13 | PA9 | bidirectional | High-speed (HSIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART1_RX, SPI0_PICO, I2C0_SCL, CLK_OUT and RTC_OUT among its functions. |
| 14 | PA10 | bidirectional | High-drive (HDIO) IO with 20 mA maximum current, with UART0_TX, SPI0_POCI, I2C0_SDA, CLK_OUT and SPI2_SCK among its functions and BSLTX (non-IOMUX) and WAKE as additional functions. |
| 15 | PA11 | bidirectional | High-drive (HDIO) IO with 20 mA maximum current, with UART0_RX, SPI0_SCK, I2C0_SCL, COMP0_OUT and TIMA1_C1 among its functions and BSLRX (non-IOMUX) and WAKE as additional functions. |
| 16 | PA12 | bidirectional | High-speed (HSIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART3_CTS, SPI0_SCK, COMP0_OUT, CAN0_TX and UART1_CTS among its functions and A0_8 (ADC0 channel 8) as a non-IOMUX analog function. |
| 17 | PA13 | bidirectional | High-speed (HSIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART3_RTS, SPI0_POCI, UART3_RX, RTC_OUT and CAN0_RX among its functions and A0_9 (ADC0 channel 9) and COMP0_IN2- as non-IOMUX analog functions. |
| 18 | PA14 | bidirectional | High-speed (HSIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART0_CTS, SPI0_PICO, UART3_TX, CLK_OUT and UART7_RX among its functions and A0_12 (ADC0 channel 12) and COMP0_IN2+ as non-IOMUX analog functions. |
| 19 | PA15 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART0_RTS, SPI1_CS2, I2C1_SCL and TIMA1_C0 among its functions, and A1_0 shared with DAC_OUT, where external circuitry on PA15 should be avoided when DAC_OUT is used. |
| 20 | PA16 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with COMP0_OUT, SPI1_POCI, I2C1_SDA, I2C2_SDA and COMP2_OUT among its functions and A1_1 (ADC1 channel 1) as a non-IOMUX analog function. |
| 21 | PA17 | bidirectional | Standard (SDIO) IO with wake capability (6 mA maximum current at VDD ≥ 2.7 V), with UART1_TX, SPI1_SCK, I2C1_SCL and TIMA0_C3 among its functions, and WAKE, A1_2 and COMP0_IN1- as non-IOMUX functions. |
| 22 | PA18 | bidirectional | Standard (SDIO) IO with wake capability (6 mA maximum current at VDD ≥ 2.7 V), with UART1_RX, SPI1_PICO, I2C1_SDA and TIMA0_C3N among its functions, and BSL_invoke, WAKE, A1_3 and COMP0_IN1+ as non-IOMUX functions. |
| 23 | PA19 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with SWDIO (2-pin serial wire debug data), SPI1_POCI, I2C1_SDA and TIMA0_C2 among its functions, and A0_13 (ADC0 channel 13) as a non-IOMUX analog function. |
| 24 | PA20 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with SWCLK (2-pin serial wire debug clock), SPI1_SCK, I2C1_SCL and TIMA0_C2N among its functions, and A0_14 (ADC0 channel 14) as a non-IOMUX analog function. |
| 25 | PA21 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART7_TX, UART1_CTS, SPI1_CS1 and TIMA0_C0 among its functions, and A1_7 (ADC1 channel 7), COMP2_IN1- and VREF- as non-IOMUX analog functions. |
| 26 | PA22 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART7_RX, SPI0_CS2, UART1_RTS, CLK_OUT and I2C0_SCL among its functions, and A0_7 (ADC0 channel 7) as a non-IOMUX analog function. |
| 27 | PA23 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART7_TX, SPI0_CS3, I2C2_SCL and TIMA0_C3 among its functions, and A1_12 (ADC1 channel 12), COMP1_IN1- and VREF+ as non-IOMUX analog functions. |
| 28 | PA24 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART7_RX, SPI0_CS2, I2C2_SDA and TIMA0_C3N among its functions, and A0_3 (ADC0 channel 3) as a non-IOMUX analog function. |
| 29 | PA25 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART3_RX, SPI1_CS3, TIMG12_C1 and UART3_TX among its functions, and A0_2 (ADC0 channel 2) as a non-IOMUX analog function. |
| 30 | PA26 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART3_TX, SPI1_CS0, TIMG8_C0, CAN0_TX and UART3_RX among its functions, and A0_1 (ADC0 channel 1) and COMP0_IN0+ as non-IOMUX analog functions. |
| 31 | PA27 | bidirectional | Standard (SDIO) IO with 6 mA maximum current at VDD ≥ 2.7 V, with UART3_RX, SPI1_CS1, CLK_OUT, RTC_OUT and CAN0_RX among its functions, and A0_0 (ADC0 channel 0) and COMP0_IN0- as non-IOMUX analog functions. |
| 32 | VCORE | power_out | Internal core-logic supply node that must only be connected to a 470 nF CVCORE capacitor to VSS, with no external voltage or load applied. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-32(5x5) |
| Category | |
| Pins | 33 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage at VDD pin | VDD | -0.3 | | 4.1 | V | At VDD pin | 54 |
| Input voltage applied to 5-V tolerant open-drain pins | VI | -0.3 | | 5.5 | V | Applied to any 5-V tolerant open-drain pins | 54 |
| Input voltage applied to common tolerance pins | VI | -0.3 | | 4.1 | V | Applied to any common tolerance pins; printed as VDD + 0.3 (4.1 MAX) | 54 |
| Current into VDD pin (source) | IVDD | | | 80 | mA | -40 °C ≤ Tj ≤ 130 °C | 54 |
| Current into VDD pin (source) | IVDD | | | 100 | mA | -40 °C ≤ Tj ≤ 90 °C | 54 |
| Current out of VSS pin (sink) | IVSS | | | 80 | mA | -40 °C ≤ Tj ≤ 130 °C | 54 |
| Current out of VSS pin (sink) | IVSS | | | 100 | mA | -40 °C ≤ Tj ≤ 90 °C | 54 |
| Current of SDIO pin | IIO | | | 6 | mA | Current sunk or sourced by SDIO pin, VDD>=2.7V | 54 |
| Current of HSIO pin | IIO | | | 6 | mA | Current sunk or sourced by HSIO pin, VDD>=2.7V | 54 |
| Current of HDIO pin | IIO | | | 20 | mA | Current sunk or sourced by HDIO pin | 54 |
| Current of ODIO pin | IIO | | | 20 | mA | Current sunk by ODIO pin | 54 |
| Supported diode current | ID | -2 | | 2 | mA | Diode current at any device pin (excluding Open Drain IO) | 54 |
| Ambient temperature | TA | -40 | | 125 | °C | Ambient temperature | 54 |
| Junction temperature | TJ | -40 | | 130 | °C | Junction temperature | 54 |
| Storage temperature | Tstg | -40 | | 150 | °C | | 54 |
| Supply voltage | VDD | 1.62 | | 3.6 | V | | 54 |
| Ambient temperature | TA | -40 | | 125 | °C | | 54 |
| Max junction temperature | TJ | | | 130 | °C | | 55 |
| MCLK, CPUCLK frequency with 2 flash wait states | fMCLK | | | 80 | MHz | PD1 bus clock; wait states managed by SYSCTL | 55 |
| MCLK, CPUCLK frequency with 1 flash wait state | fMCLK | | | 48 | MHz | PD1 bus clock; wait states managed by SYSCTL | 55 |
| MCLK, CPUCLK frequency with 0 flash wait states | fMCLK | | | 24 | MHz | PD1 bus clock; wait states managed by SYSCTL | 55 |
| ULPCLK frequency | fULPCLK | | | 40 | MHz | PD0 bus clock | 55 |
| Voltage on VCORE pin | VCORE | | 1.35 | | V | | 54 |
| Capacitor connected between VDD and VSS | CVDD | | 10 | | uF | Low-ESR capacitor, tolerance ±20% or better required | 54 |
| Capacitor connected between VCORE and VSS | CVCORE | | 470 | | nF | Low-ESR capacitor, tolerance ±20% or better required | 54 |
| Junction-to-ambient thermal resistance (VQFN-32 RHB) | RθJA | | 31.3 | | °C/W | | 56 |
| Junction-to-case (top) thermal resistance (VQFN-32 RHB) | RθJC(top) | | 22.6 | | °C/W | | 56 |
| Junction-to-board thermal resistance (VQFN-32 RHB) | RθJB | | 12.2 | | °C/W | | 56 |
| Junction-to-top characterization parameter (VQFN-32 RHB) | ΨJT | | 0.3 | | °C/W | | 56 |
| Junction-to-board characterization parameter (VQFN-32 RHB) | ΨJB | | 12.1 | | °C/W | | 56 |
| Junction-to-case (bottom) thermal resistance (VQFN-32 RHB) | RθJC(bot) | | 2.8 | | °C/W | | 56 |
| SLEEP mode supply current, MCLK=SYSPLL 80MHz, CPU halted | IDDSLEEP | | 4471 | 6678 | uA | VDD=3.3V; MCLK=SYSPLL, SYSPLLREF=SYSOSC, CPU is halted; 125 °C column | 57 |
| STOP mode supply current, STOP0 | IDDSTOP0 | | 467 | 516 | uA | VDD=3.3V; SYSOSC=32MHz, USE4MHZSTOP=0, DISABLESTOP=0; 125 °C column | 57 |
| STOP mode supply current, STOP1 | IDDSTOP1 | | 255 | 298 | uA | VDD=3.3V; SYSOSC=4MHz, USE4MHZSTOP=1, DISABLESTOP=0; 125 °C column | 57 |
| STOP mode supply current, STOP2 | IDDSTOP2 | | 86 | 123 | uA | VDD=3.3V; SYSOSC off, DISABLESTOP=1, ULPCLK=LFCLK 32kHz; 125 °C column | 57 |
| STANDBY mode supply current, STANDBY0 | IDDSTBY0 | | 29 | 105 | uA | VDD=3.3V; LFCLK=LFXT, STOPCLKSTBY=0, RTC enabled; 125 °C column | 58 |
| Power-on reset voltage level, rising | VPOR+ | 0.95 | 1.3 | 1.59 | V | | 58 |
| Power-on reset voltage level, falling | VPOR- | 0.9 | 1.25 | 1.54 | V | | 58 |
| POR hysteresis | VHYS, POR | 30 | 58 | 74 | mV | | 58 |
| Brown-out reset voltage level 0 (default), cold start rising | VBOR0+, COLD | 1.5 | 1.56 | 1.63 | V | -40 °C ≤ Ta ≤ 25 °C; cold start, rising | 59 |
| Brown-out reset voltage level 0 (default), cold start rising | VBOR0+, COLD | 1.51 | 1.58 | 1.65 | V | 25 °C ≤ Ta ≤ 125 °C; cold start, rising | 59 |
| Brown-out reset voltage level 0, rising | VBOR0+ | 1.56 | 1.59 | 1.62 | V | Rising(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 0, falling | VBOR0- | 1.55 | 1.58 | 1.61 | V | Falling(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 1, rising | VBOR1+ | 2.13 | 2.17 | 2.21 | V | Rising(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 1, falling | VBOR1- | 2.1 | 2.14 | 2.18 | V | Falling(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 2, rising | VBOR2+ | 2.73 | 2.77 | 2.82 | V | Rising(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 2, falling | VBOR2- | 2.7 | 2.74 | 2.79 | V | Falling(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 3, rising | VBOR3+ | 2.88 | 2.96 | 3.04 | V | Rising(1); device in RUN, SLEEP or STOP mode | 59 |
| Brown-out reset voltage level 3, falling | VBOR3- | 2.85 | 2.93 | 3.01 | V | Falling(1); device in RUN, SLEEP or STOP mode | 59 |
| High level input voltage, ODIO | VIH | 2 | | 5.5 | V | VDD≥2.7V | 64 |
| High level input voltage, ODIO | VIH | | | 5.5 | V | VDD≥1.62V; printed min is 0.7*VDD | 64 |
| Low level input voltage, ODIO | VIL | -0.3 | | 0.8 | V | VDD≥2.7V | 64 |
| Low level input voltage, ODIO | VIL | -0.3 | | | V | VDD≥1.62V; printed max is 0.3*VDD | 64 |
| High-Z leakage current, SDIO (all packages except PZ, PN, PM) | Ilkg | | | 50 | nA | 1.62V ≤ VDD ≤ 3.6V, -40 °C ≤ Ta ≤ 125 °C | 64 |
| Low level output voltage, SDIO | VOL | | | 0.45 | V | VDD≥2.7V, /IIO/max=6mA; -40 °C ≤ Ta ≤ 125 °C | 65 |
| Low level output voltage, HSIO | VOL | | | 0.45 | V | VDD≥2.7V, DRV=1, /IIO/max=6mA; -40 °C ≤ Ta ≤ 125 °C | 65 |
| Low level output voltage, HDIO | VOL | | | 0.4 | V | VDD≥2.7V, DRV=1(5), /IIO/max=20mA | 65 |
| Low level output voltage, ODIO | VOL | | | 0.45 | V | VDD≥2.7V, IOL,max=8mA; -40 °C ≤ Ta ≤ 125 °C | 65 |
## CAD (KiCad official)
- Symbol: `MSPM0G1518SRHBR`
- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`
- 3D model: VQFN-32(5x5) (KiCad packages3D, STEP)
- 3D model files: `mspm0g1518srhbr-etched.step` / `mspm0g1518srhbr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mspm0g1518srhbr.step` / `mspm0g1518srhbr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/mspm0g1518.pdf) (162 pp, sha256 `a6ce501f275f0727`, retrieved 2026-11-04, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mspm0g1518srhbr-datasheet.pdf)