3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMSPM0G1506SRHBR
TI(德州仪器) · IC · QFN-32(5x5)
MSPM0G1506SRHBR from TI(德州仪器), in a QFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PA0 | bidirectional | 5V-tolerant open-drain GPIO with wake-up from SHUTDOWN, default BSL I2C_SDA, and it needs an external pull-up to output high. |
| 2 | PA1 | bidirectional | 5V-tolerant open-drain GPIO with wake-up from SHUTDOWN, default BSL I2C_SCL, and it needs an external pull-up to output high. |
| 3 | NRST | input | Active-low reset input that must be pulled high to VDD or the device cannot start. |
| 4 | VDD | power_in | Power supply input with a recommended operating range of 1.62 V to 3.6 V. |
| 5 | VSS | power_in | Ground supply pin for the device. |
| 6 | PA2 | bidirectional | Standard-drive GPIO that doubles as the ROSC pin, which needs a 100 kΩ ±0.1% resistor to VSS only when the SYSOSC frequency correction loop is used. |
| 7 | PA3 | bidirectional | Standard-drive GPIO that doubles as the LFXIN input of the 32 kHz low-frequency crystal oscillator (LFXT). |
| 8 | PA4 | bidirectional | Standard-drive GPIO that doubles as the LFXOUT output of the 32 kHz crystal oscillator (LFXT) or the LFCLK_IN digital low-frequency clock input. |
| 9 | PA5 | bidirectional | Standard-drive GPIO that doubles as the HFXIN input of the high-frequency crystal oscillator (HFXT) and FCC_IN. |
| 10 | PA6 | bidirectional | Standard-drive GPIO that doubles as the HFXOUT output of the high-frequency crystal oscillator (HFXT) or the HFCLK_IN digital high-frequency clock input. |
| 11 | PA7 | bidirectional | Standard-drive GPIO that can be routed to COMP0_OUT, CLK_OUT or timer functions through IOMUX. |
| 12 | PA8 | bidirectional | Standard-drive GPIO that can be routed to UART1_TX, SPI0_CS0, UART0_RTS or TIMA0/TIMA1 functions through IOMUX. |
| 13 | PA9 | bidirectional | High-speed GPIO that can be routed to UART1_RX, SPI0_PICO, RTC_OUT, CLK_OUT or timer functions through IOMUX. |
| 14 | PA10 | bidirectional | High-drive GPIO rated for 20 mA drive strength, default BSL UART_TX, with alternates including I2C0_SDA and CLK_OUT. |
| 15 | PA11 | bidirectional | High-drive GPIO rated for 20 mA drive strength, default BSL UART_RX, with alternates including I2C0_SCL and COMP0_OUT. |
| 16 | PA12 | bidirectional | High-speed GPIO that can be routed to UART3_CTS, SPI0_SCK, TIMG0_C0 or FCC_IN through IOMUX. |
| 17 | PA13 | bidirectional | High-speed GPIO that can be routed to UART3_RTS, SPI0_POCI, UART3_RX or TIMG0_C1 through IOMUX. |
| 18 | PA14 | bidirectional | High-speed GPIO that also serves as ADC0 analog input A0_12 and COMP0_IN2+. |
| 19 | PA15 | bidirectional | Standard-drive GPIO that also serves as ADC1 analog input A1_0 and DAC_OUT; when DAC_OUT is used, A1_0 cannot sample external signals. |
| 20 | PA16 | bidirectional | Standard-drive GPIO that also serves as ADC1 analog input A1_1 and OPA1_OUT, with alternate COMP2_OUT and SPI1_POCI functions. |
| 21 | PA17 | bidirectional | Standard-drive GPIO with wake-up from SHUTDOWN that also serves as ADC1 analog input A1_2, OPA1_IN1- and COMP0_IN1-. |
| 22 | PA18 | bidirectional | Standard-drive GPIO with wake-up from SHUTDOWN that also serves as ADC1 analog input A1_3, OPA1_IN1+, COMP0_IN1+ and GPAMP_IN-, and is default BSL_Invoke. |
| 23 | PA19 | bidirectional | High-speed GPIO that serves as the SWDIO serial wire debug data input/output. |
| 24 | PA20 | bidirectional | Standard-drive GPIO that serves as the SWCLK serial wire debug clock input. |
| 25 | PA21 | bidirectional | Standard-drive GPIO that also serves as ADC1 analog input A1_7, COMP2_IN1- and the VREF- ground connection; it has an internal test connection and no injection current is allowed on this pin. |
| 26 | PA22 | bidirectional | Standard-drive GPIO that also serves as ADC0 analog input A0_7 and GPAMP_OUT/OPA0_OUT, with alternate CLK_OUT function. |
| 27 | PA23 | bidirectional | Standard-drive GPIO that serves as the VREF+ voltage reference pin, usable as external reference input or internal reference output, and also as COMP1_IN1-; a decoupling capacitor is required on VREF+ when an external reference is used. |
| 28 | PA24 | bidirectional | Standard-drive GPIO that also serves as ADC0 analog input A0_3 and OPA0_IN1-. |
| 29 | PA25 | bidirectional | Standard-drive GPIO that also serves as ADC0 analog input A0_2 and OPA0_IN1+. |
| 30 | PA26 | bidirectional | Standard-drive GPIO that also serves as ADC0 analog input A0_1, COMP0_IN0+, OPA0_IN0+ and GPAMP_IN+. |
| 31 | PA27 | bidirectional | Standard-drive GPIO that also serves as ADC0 analog input A0_0, COMP0_IN0- and OPA0_IN0-, with alternate RTC_OUT function. |
| 32 | VCORE | power_out | Regulated core supply output that must connect only to a 470 nF tank capacitor to VSS, with no other voltage or external load applied. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | TI(德州仪器) |
| Package | QFN-32(5x5) |
| Category | |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VDD | -0.3 | 4.1 | V | At VDD pin | 30 | |
| Input voltage, 5-V tolerant open-drain pins | VI | -0.3 | 5.5 | V | Applied to any 5-V tolerant open-drain pins | 30 | |
| Input voltage, common tolerance pins | VI | -0.3 | 4.1 | V | Applied to any common tolerance pins; printed VDD + 0.3 (4.1 MAX) | 30 | |
| Current into VDD pin (source) | IVDD | 80 | mA | -40℃ ≤ Tj ≤ 130℃ | 30 | ||
| Current into VDD pin (source) | IVDD | 100 | mA | -40℃ ≤ Tj ≤ 90℃ | 30 | ||
| Current out of VSS pin (sink) | IVSS | 80 | mA | -40℃ ≤ Tj ≤ 130℃ | 30 | ||
| Current out of VSS pin (sink) | IVSS | 100 | mA | -40℃ ≤ Tj ≤ 90℃ | 30 | ||
| Current of SDIO pin | IIO | 6 | mA | Current sunk or sourced by SDIO pin | 30 | ||
| Current of HSIO pin | IIO | 6 | mA | Current sunk or sourced by HSIO pin | 30 | ||
| Current of HDIO pin | IIO | 20 | mA | Current sunk or sourced by HDIO pin | 30 | ||
| Current of ODIO pin | IIO | 20 | mA | Current sunk by ODIO pin | 30 | ||
| Supported diode current | ID | -2 | 2 | mA | Diode current at any device pin | 30 | |
| Ambient temperature | TA | -40 | 125 | °C | Ambient temperature | 30 | |
| Junction temperature | TJ | -40 | 130 | °C | Junction temperature | 30 | |
| Storage temperature | Tstg | -40 | 150 | °C | Storage temperature | 30 | |
| Supply voltage | VDD | 1.62 | 3.6 | V | 30 | ||
| MCLK, CPUCLK frequency with 2 flash wait states | fMCLK | 80 | MHz | 2 flash wait states | 31 | ||
| MCLK, CPUCLK frequency with 1 flash wait state | fMCLK | 48 | MHz | 1 flash wait state | 31 | ||
| MCLK, CPUCLK frequency with 0 flash wait states | fMCLK | 24 | MHz | 0 flash wait states | 31 | ||
| ULPCLK frequency (PD0 bus clock) | fULPCLK | 40 | MHz | 31 | |||
| Ambient temperature, S version | TA | -40 | 125 | °C | S version | 30 | |
| Max junction temperature, S version | TJ | 130 | °C | S version | 30 | ||
| Junction-to-ambient thermal resistance, VQFN-32 (RHB) | RθJA | 32.1 | °C/W | VQFN-32 (RHB) | 32 | ||
| Junction-to-case (top) thermal resistance, VQFN-32 (RHB) | RθJC(top) | 23.6 | °C/W | VQFN-32 (RHB) | 32 | ||
| Junction-to-board thermal resistance, VQFN-32 (RHB) | RθJB | 13 | °C/W | VQFN-32 (RHB) | 32 | ||
| Junction-to-case (bottom) thermal resistance, VQFN-32 (RHB) | RθJC(bot) | 3.3 | °C/W | VQFN-32 (RHB) | 32 | ||
| RUN/SLEEP supply current, SLEEP mode, 80 MHz SYSPLL, CPU halted | IDDSLEEP | 3189 | 3400 | uA | MCLK=SYSPLL, SYSPLLREF=SYSOSC, CPU halted, 80MHz, VDD=3.3V, 25℃ | 33 | |
| RUN/SLEEP supply current, SLEEP mode, 80 MHz SYSPLL, CPU halted | IDDSLEEP | 3800 | 5509 | uA | MCLK=SYSPLL, SYSPLLREF=SYSOSC, CPU halted, 80MHz, VDD=3.3V, 125℃ | 33 | |
| STOP mode supply current, SYSOSC=32MHz | IDDSTOP0 | 360 | 450 | uA | SYSOSC=32MHz, USE4MHZSTOP=0, DISABLESTOP=0, ULPCLK 4MHz, VDD=3.3V, 25℃ | 33 | |
| STOP mode supply current, SYSOSC=32MHz | IDDSTOP0 | 381 | 577 | uA | SYSOSC=32MHz, USE4MHZSTOP=0, DISABLESTOP=0, ULPCLK 4MHz, VDD=3.3V, 125℃ | 33 | |
| STOP mode supply current, SYSOSC off, ULPCLK=LFCLK | IDDSTOP2 | 47 | 67 | uA | SYSOSC off, DISABLESTOP=1, ULPCLK=LFCLK 32kHz, VDD=3.3V, 25℃ | 33 | |
| STOP mode supply current, SYSOSC off, ULPCLK=LFCLK | IDDSTOP2 | 71 | 170 | uA | SYSOSC off, DISABLESTOP=1, ULPCLK=LFCLK 32kHz, VDD=3.3V, 125℃ | 33 | |
| STANDBY supply current, LFXT, RTC enabled | IDDSTBY0 | 2 | 7 | uA | LFCLK=LFXT, STOPCLKSTBY=0, RTC enabled, ULPCLK 32kHz, VDD=3.3V, 25℃ | 34 | |
| STANDBY supply current, LFXT, RTC enabled | IDDSTBY0 | 20 | 105 | uA | LFCLK=LFXT, STOPCLKSTBY=0, RTC enabled, ULPCLK 32kHz, VDD=3.3V, 125℃ | 34 | |
| High-level input voltage, ODIO | VIH | 2 | 5.5 | V | ODIO, VDD≥2.7V | 40 | |
| High-level input voltage, ODIO | VIH | 5.5 | V | ODIO, VDD≥1.62V; printed min 0.7*VDD (expression, not computed) | 40 | ||
| Low-level input voltage, ODIO | VIL | -0.3 | 0.8 | V | ODIO, VDD≥2.7V | 40 | |
| Low-level input voltage, ODIO | VIL | -0.3 | V | ODIO, VDD≥1.62V; printed max 0.3*VDD (expression, not computed) | 40 | ||
| High-Z leakage current, SDIO (all packages except PM) | Ilkg | 50 | nA | 1.62V ≤ VDD ≤ 3.6V, -40℃ ≤ Ta ≤ 125℃ | 40 | ||
| SPI controller duty cycle, SCK | DCSCK | 40 | 50 | 60 | % | Controller | 53 |
| SYSOSC frequency accuracy, FCL enabled | fSYSOSC | -0.6 | 0.68 | % | SETUSEFCL=1, Ta = 25℃ | 37 | |
| SYSOSC frequency accuracy, FCL enabled | fSYSOSC | -0.8 | 1.3 | % | SETUSEFCL=1, -40℃ ≤ Ta ≤ 125℃ | 37 | |
| SYSOSC accuracy, FCL with ±0.1% ±25ppm ROSC | fSYSOSC | -0.7 | 0.78 | % | SETUSEFCL=1, Ta = 25℃, ±0.1% ±25ppm ROSC | 37 | |
| SYSOSC accuracy, FCL with ±0.1% ±25ppm ROSC | fSYSOSC | -1.1 | 1.7 | % | SETUSEFCL=1, -40℃ ≤ Ta ≤ 125℃, ±0.1% ±25ppm ROSC | 37 | |
| SYSOSC accuracy, FCL with internal ROSC, 32MHz | fSYSOSC | -2.1 | 1.6 | % | SETUSEFCL=1, -40℃ ≤ Ta ≤ 125℃, internal ROSC, 32MHz | 37 | |
| SYSOSC accuracy, FCL disabled, 32MHz | fSYSOSC | -2.6 | 1.8 | % | SETUSEFCL=0, SYSOSCCFG.FREQ=00, -40℃ ≤ Ta ≤ 125℃ | 38 | |
| LFOSC accuracy | fLFOSC | -5 | 5 | % | -40℃ ≤ Ta ≤ 125℃ | 38 | |
| LFOSC accuracy | fLFOSC | -3 | 3 | % | -40℃ ≤ Ta ≤ 85℃ | 38 | |
| SYSPLL reference frequency range | fSYSPLLREF | 4 | 48 | MHz | 38 | ||
| VCO output frequency | fVCO | 80 | 400 | MHz | 38 | ||
| SYSPLL output duty cycle | DCPLL | 45 | 55 | % | fSYSPLLREF=32MHz, fVCO=160MHz | 38 | |
| LFXT duty cycle | DCLFXT | 30 | 70 | % | 39 | ||
| LFCLK_IN frequency | fLFIN | 29491 | 32768 | 36045 | Hz | SETUSEEXLF=1 | 39 |
| HFXT frequency | fHFXT | 4 | 8 | MHz | HFXTRSEL=00 | 39 | |
| HFXT frequency | fHFXT | 32.01 | 48 | MHz | HFXTRSEL=11 | 39 | |
| Factory trim temperature | TSTRIM | 27 | 30 | 33 | ℃ | ADC and VREF configuration: RES=0 (12-bit mode), VRSEL=0h (VDD = 3.3V), ADC tsample = 12.5uS | 46 |
| Temperature coefficient | TSc | -2.1 | -1.8 | -1.7 | mV/℃ | -40℃ ≤ Tj ≤ 130℃ | 46 |
| VREF output voltage | VREF | 1.38 | 1.4 | 1.42 | V | BUFCONFIG = 1 | 46 |
| VREF output voltage | VREF | 2.46 | 2.5 | 2.54 | V | BUFCONFIG = 0 | 46 |
| 8-bit DAC integral nonlinearity / 12-bit DAC INL | INL | -4 | 4 | LSB | 12-bit DAC, Vref = internal or external or VDD reference | 48 | |
| Differential nonlinearity, 12-bit DAC | DNL | -1 | 1 | LSB | Vref = internal or external or VDD reference | 48 | |
| Input offset voltage, comparator | Voffset | -20 | 20 | mV | Comparator input offset voltage | 47 |
CAD (KiCad official)
- Symbol:
MSPM0G1506SRHBR - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: QFN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
mspm0g1506srhbr-etched.step/mspm0g1506srhbr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mspm0g1506srhbr.step/mspm0g1506srhbr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: TI(德州仪器) datasheet (135 pp, sha256
0e4369b6aeb4218c, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).