3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMPQ4436GRE-AEC1-Z
Monolithic Power Systems · DC-DC Converters · QFN-20(4x4)
MPQ4436GRE-AEC1-Z from Monolithic Power Systems, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MODE | input | AAM or FCCM select pin: pull high for FCCM and pull low for AAM at light load, and do not leave it floating. |
| 2 | SYNCIN | input | SYNC input that accepts a 350kHz to 1000kHz clock to synchronize the oscillator, connects through a 51kΩ resistor to GND, and must be tied to GND if unused rather than left floating. |
| 3 | VIN | power_in | Input supply that powers the internal control circuitry and the power switch connected to SW, with a decoupling capacitor to ground placed close to this pin. |
| 4 | PGND | power_in | Power ground for the power stage. |
| 5 | PGND | power_in | Power ground for the power stage. |
| 6 | BST | power_out | Bootstrap pin that supplies the high-side MOSFET driver, with a bypass capacitor connected between BST and SW. |
| 7 | SW | power_out | Switch node that is the output of the internal power switch. |
| 8 | SW | power_out | Switch node that is the output of the internal power switch. |
| 9 | EN | input | Enable input that shuts the chip down when pulled below 0.85V and enables it when pulled above 1V. |
| 10 | PGND | power_in | Power ground for the power stage. |
| 11 | PGND | power_in | Power ground for the power stage. |
| 12 | VIN | power_in | Input supply that powers the internal control circuitry and the power switch connected to SW, with a decoupling capacitor to ground placed close to this pin. |
| 13 | SYNCO | output | SYNC output that provides a clock 180° out of phase with the internal oscillator or the SYNCIN clock, and is left floating if not used. |
| 14 | PG | output | Open-drain power good output that requires a pull-up resistor to the power source when used, going high when the output is within 93% to 106% of nominal and low when above 107.5% or below 91%. |
| 15 | ICS | passive | Current sharing pin that must not float and should connect to VCC or to VOUT at least 3V in a single-phase application. |
| 16 | VCC | power_in | Bias supply that powers the internal control circuit and gate drivers, requiring a decoupling capacitor to ground close to this pin. |
| 17 | AGND | power_in | Analog ground for the control circuitry. |
| 18 | FB | input | Feedback input connected to the center of the output resistor divider to AGND, with a feedback threshold voltage of 0.815V. |
| 19 | SS | passive | Soft-start input with a capacitor from SS to GND that sets the soft-start period, where the device sources 6µA into the capacitor at start-up. |
| 20 | FREQ | passive | Switching frequency program pin with a resistor from this pin to ground that sets the switching frequency per the fSW vs. RFREQ curve. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-20(4x4) |
| Category | Power Management |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN UVLO rising threshold | INUVLO_RISING | 2.8 | 3 | 3.2 | V | 6 | |
| VIN UVLO falling threshold | INUVLO_FALLING | 2.45 | 2.65 | 2.85 | V | 6 | |
| VCC voltage | VCC | 4.6 | 4.9 | 5.2 | V | IVCC = 0A | 6 |
| VIN quiescent current (sleep mode) | IQ | 18 | 26 | uA | FB = 0.85V, no load, (sleep mode) | 6 | |
| VIN shutdown current | ISHDN | 1.7 | 2.5 | uA | EN = 0V | 6 | |
| FB voltage | VFB | 0.807 | 0.815 | 0.823 | V | VIN = 3.3V to 45V, TJ = 25°C | 6 |
| FB voltage | VFB | 0.799 | 0.815 | 0.831 | V | VIN = 3.3V to 45V | 6 |
| FB current | IFB | -50 | 0 | 50 | nA | VFB = 0.85V | 6 |
| Switching frequency | fSW | 420 | 470 | 520 | kHz | RFREQ = 62kΩ | 6 |
| SYNCIN clock range | fSYNC | 350 | 1000 | kHz | External clock | 6 | |
| SYNCO high voltage | VSYNCO_HIGH | 3.3 | 4.5 | V | ISYNCO = -1mA | 6 | |
| HS current limit | ILIMIT | 10 | 13 | 16 | A | Duty cycle = 30% | 6 |
| LS valley current limit | ILIMIT_VALLEY | 8 | 10 | 12 | A | 6 | |
| ZCD current | IZCD | -0.15 | 0.1 | 0.35 | A | AAM | 6 |
| LS reverse current limit | ILIMIT_REVERSE | 2 | 4.5 | 6.5 | A | FCCM | 6 |
| Switch leakage current | ISW_LKG | 0.01 | 1 | uA | 7 | ||
| HS switch on resistance | RON_HS | 48 | 80 | mΩ | VBST - VSW = 5V | 7 | |
| LS switch on resistance | RON_LS | 20 | 40 | mΩ | VCC = 5V | 7 | |
| Soft-start current | ISS | 4 | 6 | 8 | uA | VSS = 0V | 7 |
| EN rising threshold | VEN_RISING | 0.8 | 1 | 1.2 | V | 7 | |
| EN falling threshold | VEN_FALLING | 0.65 | 0.85 | 1.05 | V | 7 | |
| PG rising threshold (VFB/VREF), VFB rising | PGRISING | 88.5 | 93 | 97.5 | % | VFB rising | 7 |
| PG rising threshold (VFB/VREF), VFB falling | PGRISING | 101.5 | 106 | 110.5 | % | VFB falling | 7 |
| PG falling threshold (VFB/VREF), VFB falling | PGFALLING | 86.5 | 91 | 95.5 | % | VFB falling | 7 |
| PG falling threshold (VFB/VREF), VFB rising | PGFALLING | 103 | 107.5 | 112 | % | VFB rising | 7 |
| PG output voltage low | VPG_LOW | 0.1 | 0.3 | V | ISINK = 1mA | 7 | |
| Supply voltage (VIN) operating range | VIN | 3.3 | 45 | V | 5 | ||
| Operating junction temperature | TJ | -40 | 150 | C | 5 | ||
| VIN, EN voltage | VIN, EN | -0.3 | 50 | V | 5 | ||
| All other pins voltage | -0.3 | 6 | V | 5 | |||
| Operating junction temperature (absolute maximum) | TJ | 150 | C | 5 | |||
| Lead temperature | 260 | C | 5 | ||||
| Storage temperature | TSTG | -65 | 150 | C | 5 | ||
| ESD Human-body model | HBM | -2 | 2 | kV | 5 | ||
| ESD Charged-device model | CDM | -750 | 750 | V | 5 | ||
| Thermal resistance junction-to-case | θJC | 9 | C/W | JESD51-7, 4-layer PCB | 5 | ||
| Thermal resistance junction-to-case (EVQ board) | θJC | 2.5 | C/W | EVQ4436-R-00A, 9cmx9cm, 4-layer PCB | 5 |
CAD (KiCad official)
- Symbol:
MPQ4436GRE-AEC1-Z - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
- 3D model files:
mpq4436gre-aec1-z-etched.step/mpq4436gre-aec1-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mpq4436gre-aec1-z.step/mpq4436gre-aec1-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (38 pp, sha256
36922d91e6ea95ba, retrieved 2026-11-02, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).