main
Ray
Publish 0.1.0
ef7bb18
MPQ4316AGRE-AEC1-Z
Monolithic Power Systems · DC-DC Converters · QFN-20(4x4)
MPQ4316AGRE-AEC1-Z from Monolithic Power Systems, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MODE | input | Selects AAM mode (pull low) or forced continuous conduction mode (pull high) at light loads; do not float. |
| 2 | SYNCIN | input | Accepts a 350kHz to 1000kHz external clock to synchronize the internal oscillator; high impedance input, do not float. |
| 3 | VIN | power_in | Input supply (3.3V to 45V) for the internal control circuitry and the power switch connected to SW; place a decoupling capacitor close to it. |
| 4 | PGND | power_in | Power ground. |
| 5 | PGND | power_in | Power ground. |
| 6 | BST | passive | Bootstrap supply for the high-side MOSFET driver; connect a bypass capacitor between BST and SW. |
| 7 | SW | power_out | Switch node, the output of the internal power MOSFETs. |
| 8 | SW | power_out | Switch node, the output of the internal power MOSFETs. |
| 9 | EN | input | Enable input; below 0.85V shuts down the chip, above 1V enables it. |
| 10 | PGND | power_in | Power ground. |
| 11 | PGND | power_in | Power ground. |
| 12 | VIN | power_in | Input supply (3.3V to 45V) for the internal control circuitry and the power switch connected to SW; place a decoupling capacitor close to it. |
| 13 | SYNCO | output | Sync clock output 180° out of phase with the internal oscillator (or opposite to the SYNCIN clock); float if unused. |
| 14 | PG | output | Open-drain power good indicator that goes high when VOUT is within 95% to 105% of nominal and low above 106.5% or below 93%; requires a pull-up resistor. |
| 15 | NC | unconnected | Not connected; float if unused. |
| 16 | VCC | power_out | 4.9V bias supply for the internal control circuit and gate drivers; connect a decoupling capacitor to ground close to the pin. |
| 17 | AGND | power_in | Analog ground. |
| 18 | FB | input | Feedback input connected to the center of the output resistor divider; feedback threshold VFB is about 0.815V. |
| 19 | SS | passive | Soft-start input; a capacitor to ground sets the soft-start time, charged by a 13µA source at start-up. |
| 20 | FREQ | passive | Switching frequency configuration; connect a resistor from FREQ to ground to set fSW (350kHz to 1000kHz). |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-20(4x4) |
| Category | Power Management |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN under-voltage lockout rising threshold | VIN_UVLO_RISING | 2.8 | 3 | 3.2 | V | VIN = 12V, VEN = 2V, TJ = -40°C to +125°C | 6 |
| VIN UVLO falling threshold | VIN_UVLO_FALLING | 2.5 | 2.7 | 2.9 | V | 6 | |
| VCC voltage | VCC | 4.6 | 4.9 | 5.2 | V | IVCC = 0A | 6 |
| VCC regulation | 1 | 4 | % | IVCC = 30mA | 6 | ||
| VIN quiescent current | IQ | 18 | 26 | μA | FB = 0.85V, no load, sleep mode | 6 | |
| VIN shutdown current | ISHDN | 1.7 | 3.5 | μA | EN=0V | 6 | |
| FB reference voltage | VFB | 0.807 | 0.815 | 0.823 | V | VIN = 3.3V to 45V, TJ = 25°C | 6 |
| FB reference voltage | VFB | 0.799 | 0.815 | 0.831 | V | VIN = 3.3V to 45V | 6 |
| FB current | IFB | -50 | 0 | 50 | nA | VFB = 0.85V | 6 |
| Switching frequency | fSW | 420 | 470 | 520 | kHz | RFREQ = 62kΩ | 6 |
| Switching frequency | fSW | 820 | 1000 | 1180 | kHz | RFREQ = 26.1kΩ | 6 |
| SYNCIN clock range | fSYNC | 350 | 1000 | kHz | External clock | 6 | |
| SYNCO high voltage | VSYNCO_HIGH | 3.3 | 4.5 | V | ISYNCO = -1mA | 6 | |
| High-side current limit | ILIMIT_HS | 10 | 13 | 16 | A | Duty cycle = 30% | 6 |
| Low-side valley current limit | ILIMIT_VALLEY | 8 | 10 | 12 | A | 6 | |
| Zero-current detection current | IZCD | -0.15 | 0.1 | 0.35 | A | AAM mode | 6 |
| LS reverse current limit | ILIMIT_REVERSE | 2 | 4.5 | 7 | A | FCCM | 6 |
| Switch leakage current | ISW_LKG | 0.01 | 1 | µA | 6 | ||
| HS-FET on resistance | RDS(ON)_HS | 48 | 80 | mΩ | VBST - VSW = 5V | 7 | |
| LS-FET on resistance | RDS(ON)_LS | 20 | 40 | mΩ | VCC = 5V | 7 | |
| Soft-start current | ISS | 8 | 13 | 19 | µA | VSS = 0V | 7 |
| EN rising threshold | VEN_RISING | 0.8 | 1 | 1.2 | V | 7 | |
| EN falling threshold | VEN_FALLING | 0.65 | 0.85 | 1.05 | V | 7 | |
| PG rising threshold | PGRISING | 92 | 95 | 98 | % of VREF | VFB rising | 7 |
| PG rising threshold | PGRISING | 102 | 105 | 108 | % of VREF | VFB falling | 7 |
| PG falling threshold | PGFALLING | 90.5 | 93.5 | 96.5 | % of VREF | VFB falling | 7 |
| PG falling threshold | PGFALLING | 103.5 | 106.5 | 109.5 | % of VREF | VFB rising | 7 |
| PG low output voltage | VPG_LOW | 0.1 | 0.3 | V | ISINK = 1mA | 7 | |
| SYNCO low voltage | VSYNCO_LOW | 0.4 | V | ISYNCO = 1mA | 6 | ||
| Supply voltage | VIN | 3.3 | 45 | V | 5 | ||
| Output voltage | VOUT | 0.815 | V | upper limit 0.95 x VIN | 5 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| VIN, EN voltage | VIN, EN | -0.3 | 50 | V | 5 | ||
| SW voltage | SW | -0.3 | V | upper limit VIN(MAX) + 0.3V | 5 | ||
| All other pins | -0.3 | 5.5 | V | 5 | |||
| Continuous power dissipation | 5.4 | W | TA = 25°C, QFN-20 (4mmx4mm) | 5 | |||
| Junction temperature | TJ | 150 | °C | 5 | |||
| Storage temperature | -65 | 150 | °C | 5 | |||
| Thermal resistance junction-to-case | θJC | 9 | °C/W | JESD51-7, QFN-20 (4mmx4mm) | 5 | ||
| Thermal resistance junction-to-case | θJC | 2.5 | °C/W | EVQ4316A-R-00A | 5 | ||
| VIN UVLO hysteresis | VIN_UVLO_HYS | 280 | mV | 6 | |||
| Minimum on time | tON_MIN | 100 | ns | 6 | |||
| Minimum off time | tOFF_MIN | 80 | ns | 6 | |||
| Thermal shutdown | TSD | 170 | °C | 7 |
CAD (KiCad official)
- Symbol:
MPQ4316AGRE-AEC1-Z - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
- 3D model files:
mpq4316agre-aec1-z-etched.step/mpq4316agre-aec1-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mpq4316agre-aec1-z.step/mpq4316agre-aec1-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (37 pp, sha256
f8463a83de3d6567, retrieved 2026-10-31, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MPQ4316AGRE-AEC1-Z
**Monolithic Power Systems** · DC-DC Converters · QFN-20(4x4)
MPQ4316AGRE-AEC1-Z from Monolithic Power Systems, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MODE | input | Selects AAM mode (pull low) or forced continuous conduction mode (pull high) at light loads; do not float. |
| 2 | SYNCIN | input | Accepts a 350kHz to 1000kHz external clock to synchronize the internal oscillator; high impedance input, do not float. |
| 3 | VIN | power_in | Input supply (3.3V to 45V) for the internal control circuitry and the power switch connected to SW; place a decoupling capacitor close to it. |
| 4 | PGND | power_in | Power ground. |
| 5 | PGND | power_in | Power ground. |
| 6 | BST | passive | Bootstrap supply for the high-side MOSFET driver; connect a bypass capacitor between BST and SW. |
| 7 | SW | power_out | Switch node, the output of the internal power MOSFETs. |
| 8 | SW | power_out | Switch node, the output of the internal power MOSFETs. |
| 9 | EN | input | Enable input; below 0.85V shuts down the chip, above 1V enables it. |
| 10 | PGND | power_in | Power ground. |
| 11 | PGND | power_in | Power ground. |
| 12 | VIN | power_in | Input supply (3.3V to 45V) for the internal control circuitry and the power switch connected to SW; place a decoupling capacitor close to it. |
| 13 | SYNCO | output | Sync clock output 180° out of phase with the internal oscillator (or opposite to the SYNCIN clock); float if unused. |
| 14 | PG | output | Open-drain power good indicator that goes high when VOUT is within 95% to 105% of nominal and low above 106.5% or below 93%; requires a pull-up resistor. |
| 15 | NC | unconnected | Not connected; float if unused. |
| 16 | VCC | power_out | 4.9V bias supply for the internal control circuit and gate drivers; connect a decoupling capacitor to ground close to the pin. |
| 17 | AGND | power_in | Analog ground. |
| 18 | FB | input | Feedback input connected to the center of the output resistor divider; feedback threshold VFB is about 0.815V. |
| 19 | SS | passive | Soft-start input; a capacitor to ground sets the soft-start time, charged by a 13µA source at start-up. |
| 20 | FREQ | passive | Switching frequency configuration; connect a resistor from FREQ to ground to set fSW (350kHz to 1000kHz). |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | QFN-20(4x4) |
| Category | Power Management |
| Pins | 21 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN under-voltage lockout rising threshold | VIN_UVLO_RISING | 2.8 | 3 | 3.2 | V | VIN = 12V, VEN = 2V, TJ = -40°C to +125°C | 6 |
| VIN UVLO falling threshold | VIN_UVLO_FALLING | 2.5 | 2.7 | 2.9 | V | | 6 |
| VCC voltage | VCC | 4.6 | 4.9 | 5.2 | V | IVCC = 0A | 6 |
| VCC regulation | | 1 | | 4 | % | IVCC = 30mA | 6 |
| VIN quiescent current | IQ | | 18 | 26 | μA | FB = 0.85V, no load, sleep mode | 6 |
| VIN shutdown current | ISHDN | | 1.7 | 3.5 | μA | EN=0V | 6 |
| FB reference voltage | VFB | 0.807 | 0.815 | 0.823 | V | VIN = 3.3V to 45V, TJ = 25°C | 6 |
| FB reference voltage | VFB | 0.799 | 0.815 | 0.831 | V | VIN = 3.3V to 45V | 6 |
| FB current | IFB | -50 | 0 | 50 | nA | VFB = 0.85V | 6 |
| Switching frequency | fSW | 420 | 470 | 520 | kHz | RFREQ = 62kΩ | 6 |
| Switching frequency | fSW | 820 | 1000 | 1180 | kHz | RFREQ = 26.1kΩ | 6 |
| SYNCIN clock range | fSYNC | 350 | | 1000 | kHz | External clock | 6 |
| SYNCO high voltage | VSYNCO_HIGH | 3.3 | | 4.5 | V | ISYNCO = -1mA | 6 |
| High-side current limit | ILIMIT_HS | 10 | 13 | 16 | A | Duty cycle = 30% | 6 |
| Low-side valley current limit | ILIMIT_VALLEY | 8 | 10 | 12 | A | | 6 |
| Zero-current detection current | IZCD | -0.15 | 0.1 | 0.35 | A | AAM mode | 6 |
| LS reverse current limit | ILIMIT_REVERSE | 2 | 4.5 | 7 | A | FCCM | 6 |
| Switch leakage current | ISW_LKG | | 0.01 | 1 | µA | | 6 |
| HS-FET on resistance | RDS(ON)_HS | | 48 | 80 | mΩ | VBST - VSW = 5V | 7 |
| LS-FET on resistance | RDS(ON)_LS | | 20 | 40 | mΩ | VCC = 5V | 7 |
| Soft-start current | ISS | 8 | 13 | 19 | µA | VSS = 0V | 7 |
| EN rising threshold | VEN_RISING | 0.8 | 1 | 1.2 | V | | 7 |
| EN falling threshold | VEN_FALLING | 0.65 | 0.85 | 1.05 | V | | 7 |
| PG rising threshold | PGRISING | 92 | 95 | 98 | % of VREF | VFB rising | 7 |
| PG rising threshold | PGRISING | 102 | 105 | 108 | % of VREF | VFB falling | 7 |
| PG falling threshold | PGFALLING | 90.5 | 93.5 | 96.5 | % of VREF | VFB falling | 7 |
| PG falling threshold | PGFALLING | 103.5 | 106.5 | 109.5 | % of VREF | VFB rising | 7 |
| PG low output voltage | VPG_LOW | | 0.1 | 0.3 | V | ISINK = 1mA | 7 |
| SYNCO low voltage | VSYNCO_LOW | | | 0.4 | V | ISYNCO = 1mA | 6 |
| Supply voltage | VIN | 3.3 | | 45 | V | | 5 |
| Output voltage | VOUT | 0.815 | | | V | upper limit 0.95 x VIN | 5 |
| Operating junction temperature | TJ | -40 | | 150 | °C | | 5 |
| VIN, EN voltage | VIN, EN | -0.3 | | 50 | V | | 5 |
| SW voltage | SW | -0.3 | | | V | upper limit VIN(MAX) + 0.3V | 5 |
| All other pins | | -0.3 | | 5.5 | V | | 5 |
| Continuous power dissipation | | | | 5.4 | W | TA = 25°C, QFN-20 (4mmx4mm) | 5 |
| Junction temperature | TJ | | | 150 | °C | | 5 |
| Storage temperature | | -65 | | 150 | °C | | 5 |
| Thermal resistance junction-to-case | θJC | | 9 | | °C/W | JESD51-7, QFN-20 (4mmx4mm) | 5 |
| Thermal resistance junction-to-case | θJC | | 2.5 | | °C/W | EVQ4316A-R-00A | 5 |
| VIN UVLO hysteresis | VIN_UVLO_HYS | | 280 | | mV | | 6 |
| Minimum on time | tON_MIN | | 100 | | ns | | 6 |
| Minimum off time | tOFF_MIN | | 80 | | ns | | 6 |
| Thermal shutdown | TSD | | 170 | | °C | | 7 |
## CAD (KiCad official)
- Symbol: `MPQ4316AGRE-AEC1-Z`
- Footprint: `Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm`
- 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
- 3D model files: `mpq4316agre-aec1-z-etched.step` / `mpq4316agre-aec1-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mpq4316agre-aec1-z.step` / `mpq4316agre-aec1-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Monolithic Power Systems datasheet](docs/mpq4316agre-aec1-z-datasheet.pdf) (37 pp, sha256 `f8463a83de3d6567`, retrieved 2026-10-31, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mpq4316agre-aec1-z-datasheet.pdf)