Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MPQ4316AGRE-AEC1-Z

Monolithic Power Systems · DC-DC Converters · QFN-20(4x4)

MPQ4316AGRE-AEC1-Z from Monolithic Power Systems, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 MODE input Selects AAM mode (pull low) or forced continuous conduction mode (pull high) at light loads; do not float.
2 SYNCIN input Accepts a 350kHz to 1000kHz external clock to synchronize the internal oscillator; high impedance input, do not float.
3 VIN power_in Input supply (3.3V to 45V) for the internal control circuitry and the power switch connected to SW; place a decoupling capacitor close to it.
4 PGND power_in Power ground.
5 PGND power_in Power ground.
6 BST passive Bootstrap supply for the high-side MOSFET driver; connect a bypass capacitor between BST and SW.
7 SW power_out Switch node, the output of the internal power MOSFETs.
8 SW power_out Switch node, the output of the internal power MOSFETs.
9 EN input Enable input; below 0.85V shuts down the chip, above 1V enables it.
10 PGND power_in Power ground.
11 PGND power_in Power ground.
12 VIN power_in Input supply (3.3V to 45V) for the internal control circuitry and the power switch connected to SW; place a decoupling capacitor close to it.
13 SYNCO output Sync clock output 180° out of phase with the internal oscillator (or opposite to the SYNCIN clock); float if unused.
14 PG output Open-drain power good indicator that goes high when VOUT is within 95% to 105% of nominal and low above 106.5% or below 93%; requires a pull-up resistor.
15 NC unconnected Not connected; float if unused.
16 VCC power_out 4.9V bias supply for the internal control circuit and gate drivers; connect a decoupling capacitor to ground close to the pin.
17 AGND power_in Analog ground.
18 FB input Feedback input connected to the center of the output resistor divider; feedback threshold VFB is about 0.815V.
19 SS passive Soft-start input; a capacitor to ground sets the soft-start time, charged by a 13µA source at start-up.
20 FREQ passive Switching frequency configuration; connect a resistor from FREQ to ground to set fSW (350kHz to 1000kHz).
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package QFN-20(4x4)
Category Power Management
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN under-voltage lockout rising threshold VIN_UVLO_RISING 2.8 3 3.2 V VIN = 12V, VEN = 2V, TJ = -40°C to +125°C 6
VIN UVLO falling threshold VIN_UVLO_FALLING 2.5 2.7 2.9 V 6
VCC voltage VCC 4.6 4.9 5.2 V IVCC = 0A 6
VCC regulation 1 4 % IVCC = 30mA 6
VIN quiescent current IQ 18 26 μA FB = 0.85V, no load, sleep mode 6
VIN shutdown current ISHDN 1.7 3.5 μA EN=0V 6
FB reference voltage VFB 0.807 0.815 0.823 V VIN = 3.3V to 45V, TJ = 25°C 6
FB reference voltage VFB 0.799 0.815 0.831 V VIN = 3.3V to 45V 6
FB current IFB -50 0 50 nA VFB = 0.85V 6
Switching frequency fSW 420 470 520 kHz RFREQ = 62kΩ 6
Switching frequency fSW 820 1000 1180 kHz RFREQ = 26.1kΩ 6
SYNCIN clock range fSYNC 350 1000 kHz External clock 6
SYNCO high voltage VSYNCO_HIGH 3.3 4.5 V ISYNCO = -1mA 6
High-side current limit ILIMIT_HS 10 13 16 A Duty cycle = 30% 6
Low-side valley current limit ILIMIT_VALLEY 8 10 12 A 6
Zero-current detection current IZCD -0.15 0.1 0.35 A AAM mode 6
LS reverse current limit ILIMIT_REVERSE 2 4.5 7 A FCCM 6
Switch leakage current ISW_LKG 0.01 1 µA 6
HS-FET on resistance RDS(ON)_HS 48 80 mΩ VBST - VSW = 5V 7
LS-FET on resistance RDS(ON)_LS 20 40 mΩ VCC = 5V 7
Soft-start current ISS 8 13 19 µA VSS = 0V 7
EN rising threshold VEN_RISING 0.8 1 1.2 V 7
EN falling threshold VEN_FALLING 0.65 0.85 1.05 V 7
PG rising threshold PGRISING 92 95 98 % of VREF VFB rising 7
PG rising threshold PGRISING 102 105 108 % of VREF VFB falling 7
PG falling threshold PGFALLING 90.5 93.5 96.5 % of VREF VFB falling 7
PG falling threshold PGFALLING 103.5 106.5 109.5 % of VREF VFB rising 7
PG low output voltage VPG_LOW 0.1 0.3 V ISINK = 1mA 7
SYNCO low voltage VSYNCO_LOW 0.4 V ISYNCO = 1mA 6
Supply voltage VIN 3.3 45 V 5
Output voltage VOUT 0.815 V upper limit 0.95 x VIN 5
Operating junction temperature TJ -40 150 °C 5
VIN, EN voltage VIN, EN -0.3 50 V 5
SW voltage SW -0.3 V upper limit VIN(MAX) + 0.3V 5
All other pins -0.3 5.5 V 5
Continuous power dissipation 5.4 W TA = 25°C, QFN-20 (4mmx4mm) 5
Junction temperature TJ 150 °C 5
Storage temperature -65 150 °C 5
Thermal resistance junction-to-case θJC 9 °C/W JESD51-7, QFN-20 (4mmx4mm) 5
Thermal resistance junction-to-case θJC 2.5 °C/W EVQ4316A-R-00A 5
VIN UVLO hysteresis VIN_UVLO_HYS 280 mV 6
Minimum on time tON_MIN 100 ns 6
Minimum off time tOFF_MIN 80 ns 6
Thermal shutdown TSD 170 °C 7

CAD (KiCad official)

  • Symbol: MPQ4316AGRE-AEC1-Z
  • Footprint: Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm
  • 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
  • 3D model files: mpq4316agre-aec1-z-etched.step / mpq4316agre-aec1-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mpq4316agre-aec1-z.step / mpq4316agre-aec1-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (37 pp, sha256 f8463a83de3d6567, retrieved 2026-10-31, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF