main
Ray
Publish 0.1.0
2c72223
MPQ3362GJ-AEC1-Z
Monolithic Power Systems · LED Drivers · TSOT-23-8
MPQ3362GJ-AEC1-Z from Monolithic Power Systems, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | passive | Output switch node, the drain of the internal N-channel MOSFET (40V rated), connected to the inductor and rectifier to complete the boost converter. |
| 2 | VIN | power_in | Input supply pin, 3V to 36V operating range, connectable to the input supply or to the output for bootstrapped operation. |
| 3 | COMP | passive | Error amplifier output compensation pin, connected to a series RC network to compensate the regulator control loop. |
| 4 | EN/DIM | input | Enable and dimming pin: low for 20ms disables the IC, PWM below 2kHz gives PWM dimming, and PWM above 5kHz gives analog dimming. |
| 5 | OSC/SYNC | bidirectional | Switching frequency setting and synchronization pin: a resistor sets fSW between 200kHz and 2.2MHz, or a 200kHz to 2.2MHz pulse signal synchronizes it. |
| 6 | FB | input | Regulation feedback input with a 0.2V regulation threshold. |
| 7 | OVP | input | Open LED protection pin that senses the output voltage through a divider, with a 1.18V typical threshold, to protect the IC during open LED operation. |
| 8 | GND | power_in | Ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | TSOT-23-8 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| IN shutdown supply current | 0.3 | 1.5 | μA | VEN ≤ 0V | 4 | ||
| IN operating supply current | IQ1 | 1 | 1.25 | mA | VEN > 2V, VFB = 0.5V | 4 | |
| IN operating supply current (switching) | IQ2 | 2.5 | mA | With switching, 400kHz | 4 | ||
| IN under-voltage lockout threshold | VUVLO | 2.35 | 2.5 | 2.65 | V | VIN rising | 4 |
| IN under-voltage lockout hysteresis | VUVLO_HYS | 100 | mV | 4 | |||
| EN/DIM input low voltage | VEN_L | 0.4 | V | 4 | |||
| EN/DIM input high voltage | VEN_H | 1.3 | V | 4 | |||
| EN/DIM input bias current | IEN | 7 | μA | VEN = 5V | 4 | ||
| EN power off time | tEN | 16 | 20 | 24 | ms | EN/DIM pulls low to disable the IC | 4 |
| SW switching frequency | fSW | 360 | 400 | 440 | kHz | ROSC = 100kΩ | 4 |
| SW switching frequency | fSW | 1650 | 1850 | 2050 | kHz | ROSC = 20kΩ | 4 |
| SW maximum duty cycle | 90 | 93 | % | VFB = 0.15V, fSW = 400kHz | 4 | ||
| Error amplifier transconductance | GEA | 250 | μA/V | 4 | |||
| COMP maximum output current | IEA | 30 | μA | Source and sink | 4 | ||
| FB regulation threshold | VFB | 196 | 200 | 204 | mV | 100% analog dimming (25°C) | 4 |
| FB regulation threshold | VFB | 195 | 200 | 205 | mV | 100% analog dimming (-40°C to +125°C) | 4 |
| FB input biased current | IFB | 2.5 | μA | VFB = 0.5V | 4 | ||
| SW on resistance | RON | 80 | mΩ | VIN = 4V | 4 | ||
| SW current limit | ILIM | 3.4 | 4 | 4.6 | A | Duty = 80% | 4 |
| SW leakage current | ISW | 1.5 | μA | VSW = 36V | 4 | ||
| OVP threshold | VOVP | 1.1 | 1.18 | 1.26 | V | 4 | |
| OVP hysteresis | VOVP_HYS | 100 | mV | 4 | |||
| OVP under-voltage threshold | VOVP_UV | 50 | 100 | mV | 4 | ||
| Short load protection | VSP | 540 | 600 | 660 | mV | VFB > VSP, short load protection is triggered | 4 |
| Latch-off current limit | ICL | 6.5 | A | 4 | |||
| Thermal shutdown | TSD | 170 | °C | Not tested in production. Guaranteed by characterization | 4 | ||
| Thermal shutdown hysteresis | TSD_HYS | 20 | °C | 4 | |||
| VIN, VSW absolute maximum | VIN, VSW | -0.3 | 40 | V | 3 | ||
| All other pins absolute maximum | -0.3 | 5.3 | V | 3 | |||
| Continuous power dissipation | PD | 1.25 | W | TA = 25°C, TSOT23-8 | 3 | ||
| Junction temperature | TJ | 150 | °C | 3 | |||
| Storage temperature | -65 | 150 | °C | 3 | |||
| ESD HBM | -2000 | 2000 | V | Human body model | 3 | ||
| ESD CDM | -1000 | 1000 | V | Charged device model | 3 | ||
| Supply voltage | VIN | 3 | 36 | V | 3 | ||
| Maximum LED load voltage | VLED | 36 | V | 3 | |||
| Operating junction temperature | TJ | -40 | 125 | °C | 3 | ||
| Thermal resistance junction-to-ambient | θJA | 100 | °C/W | TSOT23-8, JESD51-7 4-layer PCB | 3 |
CAD (KiCad official)
- Symbol:
MPQ3362GJ-AEC1-Z - Footprint:
Package_TO_SOT_SMD:TSOT-23-8 - 3D model: TSOT-23-8 (KiCad packages3D, STEP)
- 3D model files:
mpq3362gj-aec1-z-etched.step/mpq3362gj-aec1-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mpq3362gj-aec1-z.step/mpq3362gj-aec1-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (17 pp, sha256
b03c77020b766c90, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MPQ3362GJ-AEC1-Z
**Monolithic Power Systems** · LED Drivers · TSOT-23-8
MPQ3362GJ-AEC1-Z from Monolithic Power Systems, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | passive | Output switch node, the drain of the internal N-channel MOSFET (40V rated), connected to the inductor and rectifier to complete the boost converter. |
| 2 | VIN | power_in | Input supply pin, 3V to 36V operating range, connectable to the input supply or to the output for bootstrapped operation. |
| 3 | COMP | passive | Error amplifier output compensation pin, connected to a series RC network to compensate the regulator control loop. |
| 4 | EN/DIM | input | Enable and dimming pin: low for 20ms disables the IC, PWM below 2kHz gives PWM dimming, and PWM above 5kHz gives analog dimming. |
| 5 | OSC/SYNC | bidirectional | Switching frequency setting and synchronization pin: a resistor sets fSW between 200kHz and 2.2MHz, or a 200kHz to 2.2MHz pulse signal synchronizes it. |
| 6 | FB | input | Regulation feedback input with a 0.2V regulation threshold. |
| 7 | OVP | input | Open LED protection pin that senses the output voltage through a divider, with a 1.18V typical threshold, to protect the IC during open LED operation. |
| 8 | GND | power_in | Ground. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | TSOT-23-8 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| IN shutdown supply current | | | 0.3 | 1.5 | μA | VEN ≤ 0V | 4 |
| IN operating supply current | IQ1 | | 1 | 1.25 | mA | VEN > 2V, VFB = 0.5V | 4 |
| IN operating supply current (switching) | IQ2 | | 2.5 | | mA | With switching, 400kHz | 4 |
| IN under-voltage lockout threshold | VUVLO | 2.35 | 2.5 | 2.65 | V | VIN rising | 4 |
| IN under-voltage lockout hysteresis | VUVLO_HYS | | 100 | | mV | | 4 |
| EN/DIM input low voltage | VEN_L | | | 0.4 | V | | 4 |
| EN/DIM input high voltage | VEN_H | 1.3 | | | V | | 4 |
| EN/DIM input bias current | IEN | | | 7 | μA | VEN = 5V | 4 |
| EN power off time | tEN | 16 | 20 | 24 | ms | EN/DIM pulls low to disable the IC | 4 |
| SW switching frequency | fSW | 360 | 400 | 440 | kHz | ROSC = 100kΩ | 4 |
| SW switching frequency | fSW | 1650 | 1850 | 2050 | kHz | ROSC = 20kΩ | 4 |
| SW maximum duty cycle | | 90 | 93 | | % | VFB = 0.15V, fSW = 400kHz | 4 |
| Error amplifier transconductance | GEA | | 250 | | μA/V | | 4 |
| COMP maximum output current | IEA | | 30 | | μA | Source and sink | 4 |
| FB regulation threshold | VFB | 196 | 200 | 204 | mV | 100% analog dimming (25°C) | 4 |
| FB regulation threshold | VFB | 195 | 200 | 205 | mV | 100% analog dimming (-40°C to +125°C) | 4 |
| FB input biased current | IFB | | | 2.5 | μA | VFB = 0.5V | 4 |
| SW on resistance | RON | | 80 | | mΩ | VIN = 4V | 4 |
| SW current limit | ILIM | 3.4 | 4 | 4.6 | A | Duty = 80% | 4 |
| SW leakage current | ISW | | | 1.5 | μA | VSW = 36V | 4 |
| OVP threshold | VOVP | 1.1 | 1.18 | 1.26 | V | | 4 |
| OVP hysteresis | VOVP_HYS | | 100 | | mV | | 4 |
| OVP under-voltage threshold | VOVP_UV | 50 | | 100 | mV | | 4 |
| Short load protection | VSP | 540 | 600 | 660 | mV | VFB > VSP, short load protection is triggered | 4 |
| Latch-off current limit | ICL | | 6.5 | | A | | 4 |
| Thermal shutdown | TSD | | 170 | | °C | Not tested in production. Guaranteed by characterization | 4 |
| Thermal shutdown hysteresis | TSD_HYS | | 20 | | °C | | 4 |
| VIN, VSW absolute maximum | VIN, VSW | -0.3 | | 40 | V | | 3 |
| All other pins absolute maximum | | -0.3 | | 5.3 | V | | 3 |
| Continuous power dissipation | PD | | | 1.25 | W | TA = 25°C, TSOT23-8 | 3 |
| Junction temperature | TJ | | | 150 | °C | | 3 |
| Storage temperature | | -65 | | 150 | °C | | 3 |
| ESD HBM | | -2000 | | 2000 | V | Human body model | 3 |
| ESD CDM | | -1000 | | 1000 | V | Charged device model | 3 |
| Supply voltage | VIN | 3 | | 36 | V | | 3 |
| Maximum LED load voltage | VLED | | | 36 | V | | 3 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 3 |
| Thermal resistance junction-to-ambient | θJA | | 100 | | °C/W | TSOT23-8, JESD51-7 4-layer PCB | 3 |
## CAD (KiCad official)
- Symbol: `MPQ3362GJ-AEC1-Z`
- Footprint: `Package_TO_SOT_SMD:TSOT-23-8`
- 3D model: TSOT-23-8 (KiCad packages3D, STEP)
- 3D model files: `mpq3362gj-aec1-z-etched.step` / `mpq3362gj-aec1-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mpq3362gj-aec1-z.step` / `mpq3362gj-aec1-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Monolithic Power Systems datasheet](docs/mpq3362gj-aec1-z-datasheet.pdf) (17 pp, sha256 `b03c77020b766c90`, retrieved 2026-10-23, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mpq3362gj-aec1-z-datasheet.pdf)