main
Ray
Publish 0.1.0
b5da484
MP6600LGR-Z
MONOLITHIC POWER SYSTEMS INC. · Global Sourcing Parts · QFN-24(4x4)
MP6600LGR-Z from MONOLITHIC POWER SYSTEMS INC., in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DIR | input | Direction input that sets the direction of stepper motor rotation, with an internal pull-down resistor. |
| 2 | nFAULT | output | Open-drain fault indication output that is driven low on a fault condition such as OCP, OTP or OVP. |
| 3 | ISET | passive | Current set programming pin; a resistor from ISET to ground sets the motor current. |
| 4 | AGND | power_in | Analog ground. |
| 5 | ROSC | passive | Constant-off-time programming pin; a resistor from ROSC to ground sets the PWM off time. |
| 6 | MS2 | input | Mode selection input that sets the step mode together with MS1 (full, half, quarter or eighth step). |
| 7 | MS1 | input | Mode selection input that sets the step mode together with MS2; it has an internal pull-down resistor. |
| 8 | GND | power_in | Power ground. |
| 9 | BOUT1 | output | Bridge B output terminal 1. |
| 10 | VIN | power_in | Input supply voltage; both VIN pins must be connected to the same supply and VIN must be decoupled to ground with a minimum 100nF ceramic capacitor. |
| 11 | BOUT2 | output | Bridge B output terminal 2. |
| 12 | GND | power_in | Power ground. |
| 13 | STEP | input | Step input; each rising edge advances the motor by one increment and it has an internal pull-down resistor. |
| 14 | VCP | power_out | Charge pump output; connect a 1µF, 16V, X7R ceramic capacitor from VCP to VIN. |
| 15 | CP2 | passive | Charge pump capacitor terminal; connect a 100nF, X7R ceramic capacitor rated for at least the VIN voltage between CP1 and CP2. |
| 16 | CP1 | passive | Charge pump capacitor terminal; connect a 100nF, X7R ceramic capacitor rated for at least the VIN voltage between CP1 and CP2. |
| 17 | VG | power_out | Low-side MOSFET gate drive voltage; connect a 220nF, 16V, X7R ceramic capacitor from VG to ground. |
| 18 | ENBL | input | Enable input; driving it low disables the bridge outputs and translator operation, and it has an internal pull-down resistor. |
| 19 | nSLEEP | input | Sleep mode input; drive to logic high for normal operation, and it has an internal pull-down resistor. |
| 20 | GND | power_in | Power ground. |
| 21 | AOUT2 | output | Bridge A output terminal 2. |
| 22 | VIN | power_in | Input supply voltage; both VIN pins must be connected to the same supply and VIN must be decoupled to ground with a minimum 100nF ceramic capacitor. |
| 23 | AOUT1 | output | Bridge A output terminal 1. |
| 24 | GND | power_in | Power ground. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MONOLITHIC POWER SYSTEMS INC. |
| Package | QFN-24(4x4) |
| Category | Global Sourcing Parts |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VIN | 4.5 | 35 | V | 4 | ||
| Output current | IA/BOUT | -1.5 | 1.5 | A | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Supply voltage | VIN | -0.3 | 40 | V | 4 | ||
| xOUTx voltage | VA/BOUT1/2 | -0.7 | 40 | V | 4 | ||
| Charge pump voltage | VCP, CP2 | 6.5 | V | VIN to VIN + 6.5V (referenced to VIN) | 4 | ||
| All other pins to AGND | -0.3 | 6.5 | V | 4 | |||
| Continuous power dissipation | PD | 2.9 | W | TA = 25°C | 4 | ||
| Storage temperature | TSTORE | -55 | 150 | °C | 4 | ||
| Junction temperature | TJ | 150 | °C | 4 | |||
| Lead temperature (solder) | 260 | °C | 4 | ||||
| ESD Human body model | HBM | -2 | 2 | kV | 4 | ||
| ESD Charged device model | CDM | -2 | 2 | kV | 4 | ||
| Input supply voltage | VIN | 4.5 | 24 | 35 | V | 5 | |
| Quiescent current | IQ | 1.5 | 5 | mA | VIN = 24V, ENBL = 1, nSLEEP = 1, with no load | 5 | |
| Sleep current | ISLEEP | 1 | µA | VIN = 24V, nSLEEP = 0 | 5 | ||
| Output on resistance HS-FET | RHS | 0.195 | 0.3 | Ω | VIN = 24V, IOUT = 1A, TJ = 25°C | 5 | |
| Output on resistance HS-FET | RHS | 0.25 | Ω | VIN = 24V, IOUT = 1A, TJ = 85°C | 5 | ||
| Output on resistance LS-FET | RLS | 0.17 | 0.3 | Ω | VIN = 24V, IOUT = 1A, TJ = 25°C | 5 | |
| Output on resistance LS-FET | RLS | 0.25 | Ω | VIN = 24V, IOUT = 1A, TJ = 85°C | 5 | ||
| Body diode forward voltage | VF | 1.1 | V | IOUT = 1.5A | 5 | ||
| Input logic low threshold | VIL | 0.8 | V | 5 | |||
| Input logic high threshold | VIH | 2.1 | V | 5 | |||
| Logic input current high | IIN(H) | 20 | µA | VIH = 5V | 5 | ||
| Logic input current low | IIN(L) | 5 | µA | VIL = 0.8V | 5 | ||
| Output low voltage | VOL | 0.5 | V | IO = 5mA | 5 | ||
| Output high leakage current | IOH | 1 | µA | VO = 3.3V | 5 | ||
| UVLO rising threshold | VIN_RISE | 3.3 | 3.6 | 4 | V | 5 | |
| UVLO falling threshold | VIN_FALL | 3 | 3.3 | 3.7 | V | 5 | |
| Input OVP threshold | VOVP | 36 | 37.5 | 38.5 | V | 5 | |
| Over-current trip level sinking | IOCP1 | 3.5 | 6 | 8.5 | A | Sinking | 5 |
| Over-current trip level sourcing | IOCP2 | 3.5 | 6 | 8.5 | A | Sourcing | 5 |
| Constant-off-time | tOFF | 19 | 23 | 26 | µs | Rt = 200kΩ | 5 |
| Peak current regulation level | IPEAK | 0.95 | 1 | 1.05 | A | RISET = 71kΩ | 5 |
| ISET voltage | VISET | 0.8 | 0.9 | 1 | V | 5 | |
| ISET current ratio | AISET | 11 | 12.676 | 14 | µA/A | 5 | |
| Current trip accuracy | ΔITRIP | -5 | 5 | % | RISET = 71kΩ, 71% to 100% | 5 | |
| Current trip accuracy | ΔITRIP | -9 | 9 | % | RISET = 71kΩ, 38% to 67% | 5 | |
| Current trip accuracy | ΔITRIP | -12 | 12 | % | RISET = 71kΩ, <34% | 5 | |
| STEP high time | t1 | 1 | µs | 6 | |||
| STEP low time | t2 | 1 | µs | 6 | |||
| Set-up time MSx, DIR to STEP rising | t3 | 200 | ns | 6 | |||
| Hold time STEP rising to MSx, DIR change | t4 | 200 | ns | 6 | |||
| Reserved row: RPD internal pull-down resistance | RPD | 500 | kΩ | 5 | |||
| Input OVP hysteresis | ΔVOVP | 1900 | mV | 5 | |||
| Over-current deglitch time | tOCP | 1 | µs | Guaranteed by design (note 5) | 5 | ||
| Thermal shutdown | TTSD | 165 | °C | Guaranteed by design (note 5) | 5 | ||
| Thermal shutdown hysteresis | ΔTTSD | 15 | °C | Guaranteed by design (note 5) | 5 | ||
| Blanking time | tBLANK | 2 | µs | Guaranteed by design (note 5) | 5 | ||
| Thermal resistance junction-to-ambient | θJA | 42 | °C/W | QFN-24 (4mmx4mm), JESD51-7 4-layer PCB | 4 | ||
| Thermal resistance junction-to-case | θJC | 9 | °C/W | QFN-24 (4mmx4mm) | 4 |
CAD (KiCad official)
- Symbol:
MP6600LGR-Z - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files:
mp6600lgr-z-etched.step/mp6600lgr-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp6600lgr-z.step/mp6600lgr-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MONOLITHIC POWER SYSTEMS INC. datasheet, copy hosted by LCSC (21 pp, sha256
5d477fc1c0631eaa, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MP6600LGR-Z
**MONOLITHIC POWER SYSTEMS INC.** · Global Sourcing Parts · QFN-24(4x4)
MP6600LGR-Z from MONOLITHIC POWER SYSTEMS INC., in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DIR | input | Direction input that sets the direction of stepper motor rotation, with an internal pull-down resistor. |
| 2 | nFAULT | output | Open-drain fault indication output that is driven low on a fault condition such as OCP, OTP or OVP. |
| 3 | ISET | passive | Current set programming pin; a resistor from ISET to ground sets the motor current. |
| 4 | AGND | power_in | Analog ground. |
| 5 | ROSC | passive | Constant-off-time programming pin; a resistor from ROSC to ground sets the PWM off time. |
| 6 | MS2 | input | Mode selection input that sets the step mode together with MS1 (full, half, quarter or eighth step). |
| 7 | MS1 | input | Mode selection input that sets the step mode together with MS2; it has an internal pull-down resistor. |
| 8 | GND | power_in | Power ground. |
| 9 | BOUT1 | output | Bridge B output terminal 1. |
| 10 | VIN | power_in | Input supply voltage; both VIN pins must be connected to the same supply and VIN must be decoupled to ground with a minimum 100nF ceramic capacitor. |
| 11 | BOUT2 | output | Bridge B output terminal 2. |
| 12 | GND | power_in | Power ground. |
| 13 | STEP | input | Step input; each rising edge advances the motor by one increment and it has an internal pull-down resistor. |
| 14 | VCP | power_out | Charge pump output; connect a 1µF, 16V, X7R ceramic capacitor from VCP to VIN. |
| 15 | CP2 | passive | Charge pump capacitor terminal; connect a 100nF, X7R ceramic capacitor rated for at least the VIN voltage between CP1 and CP2. |
| 16 | CP1 | passive | Charge pump capacitor terminal; connect a 100nF, X7R ceramic capacitor rated for at least the VIN voltage between CP1 and CP2. |
| 17 | VG | power_out | Low-side MOSFET gate drive voltage; connect a 220nF, 16V, X7R ceramic capacitor from VG to ground. |
| 18 | ENBL | input | Enable input; driving it low disables the bridge outputs and translator operation, and it has an internal pull-down resistor. |
| 19 | nSLEEP | input | Sleep mode input; drive to logic high for normal operation, and it has an internal pull-down resistor. |
| 20 | GND | power_in | Power ground. |
| 21 | AOUT2 | output | Bridge A output terminal 2. |
| 22 | VIN | power_in | Input supply voltage; both VIN pins must be connected to the same supply and VIN must be decoupled to ground with a minimum 100nF ceramic capacitor. |
| 23 | AOUT1 | output | Bridge A output terminal 1. |
| 24 | GND | power_in | Power ground. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MONOLITHIC POWER SYSTEMS INC. |
| Package | QFN-24(4x4) |
| Category | Global Sourcing Parts |
| Pins | 25 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VIN | 4.5 | | 35 | V | | 4 |
| Output current | IA/BOUT | -1.5 | | 1.5 | A | | 4 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 4 |
| Supply voltage | VIN | -0.3 | | 40 | V | | 4 |
| xOUTx voltage | VA/BOUT1/2 | -0.7 | | 40 | V | | 4 |
| Charge pump voltage | VCP, CP2 | | | 6.5 | V | VIN to VIN + 6.5V (referenced to VIN) | 4 |
| All other pins to AGND | | -0.3 | | 6.5 | V | | 4 |
| Continuous power dissipation | PD | | | 2.9 | W | TA = 25°C | 4 |
| Storage temperature | TSTORE | -55 | | 150 | °C | | 4 |
| Junction temperature | TJ | | | 150 | °C | | 4 |
| Lead temperature (solder) | | | | 260 | °C | | 4 |
| ESD Human body model | HBM | -2 | | 2 | kV | | 4 |
| ESD Charged device model | CDM | -2 | | 2 | kV | | 4 |
| Input supply voltage | VIN | 4.5 | 24 | 35 | V | | 5 |
| Quiescent current | IQ | | 1.5 | 5 | mA | VIN = 24V, ENBL = 1, nSLEEP = 1, with no load | 5 |
| Sleep current | ISLEEP | | | 1 | µA | VIN = 24V, nSLEEP = 0 | 5 |
| Output on resistance HS-FET | RHS | | 0.195 | 0.3 | Ω | VIN = 24V, IOUT = 1A, TJ = 25°C | 5 |
| Output on resistance HS-FET | RHS | | | 0.25 | Ω | VIN = 24V, IOUT = 1A, TJ = 85°C | 5 |
| Output on resistance LS-FET | RLS | | 0.17 | 0.3 | Ω | VIN = 24V, IOUT = 1A, TJ = 25°C | 5 |
| Output on resistance LS-FET | RLS | | | 0.25 | Ω | VIN = 24V, IOUT = 1A, TJ = 85°C | 5 |
| Body diode forward voltage | VF | | | 1.1 | V | IOUT = 1.5A | 5 |
| Input logic low threshold | VIL | | | 0.8 | V | | 5 |
| Input logic high threshold | VIH | 2.1 | | | V | | 5 |
| Logic input current high | IIN(H) | | | 20 | µA | VIH = 5V | 5 |
| Logic input current low | IIN(L) | | | 5 | µA | VIL = 0.8V | 5 |
| Output low voltage | VOL | | | 0.5 | V | IO = 5mA | 5 |
| Output high leakage current | IOH | | | 1 | µA | VO = 3.3V | 5 |
| UVLO rising threshold | VIN_RISE | 3.3 | 3.6 | 4 | V | | 5 |
| UVLO falling threshold | VIN_FALL | 3 | 3.3 | 3.7 | V | | 5 |
| Input OVP threshold | VOVP | 36 | 37.5 | 38.5 | V | | 5 |
| Over-current trip level sinking | IOCP1 | 3.5 | 6 | 8.5 | A | Sinking | 5 |
| Over-current trip level sourcing | IOCP2 | 3.5 | 6 | 8.5 | A | Sourcing | 5 |
| Constant-off-time | tOFF | 19 | 23 | 26 | µs | Rt = 200kΩ | 5 |
| Peak current regulation level | IPEAK | 0.95 | 1 | 1.05 | A | RISET = 71kΩ | 5 |
| ISET voltage | VISET | 0.8 | 0.9 | 1 | V | | 5 |
| ISET current ratio | AISET | 11 | 12.676 | 14 | µA/A | | 5 |
| Current trip accuracy | ΔITRIP | -5 | | 5 | % | RISET = 71kΩ, 71% to 100% | 5 |
| Current trip accuracy | ΔITRIP | -9 | | 9 | % | RISET = 71kΩ, 38% to 67% | 5 |
| Current trip accuracy | ΔITRIP | -12 | | 12 | % | RISET = 71kΩ, <34% | 5 |
| STEP high time | t1 | 1 | | | µs | | 6 |
| STEP low time | t2 | 1 | | | µs | | 6 |
| Set-up time MSx, DIR to STEP rising | t3 | 200 | | | ns | | 6 |
| Hold time STEP rising to MSx, DIR change | t4 | 200 | | | ns | | 6 |
| Reserved row: RPD internal pull-down resistance | RPD | | 500 | | kΩ | | 5 |
| Input OVP hysteresis | ΔVOVP | | 1900 | | mV | | 5 |
| Over-current deglitch time | tOCP | | 1 | | µs | Guaranteed by design (note 5) | 5 |
| Thermal shutdown | TTSD | | 165 | | °C | Guaranteed by design (note 5) | 5 |
| Thermal shutdown hysteresis | ΔTTSD | | 15 | | °C | Guaranteed by design (note 5) | 5 |
| Blanking time | tBLANK | | 2 | | µs | Guaranteed by design (note 5) | 5 |
| Thermal resistance junction-to-ambient | θJA | | 42 | | °C/W | QFN-24 (4mmx4mm), JESD51-7 4-layer PCB | 4 |
| Thermal resistance junction-to-case | θJC | | 9 | | °C/W | QFN-24 (4mmx4mm) | 4 |
## CAD (KiCad official)
- Symbol: `MP6600LGR-Z`
- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`
- 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files: `mp6600lgr-z-etched.step` / `mp6600lgr-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mp6600lgr-z.step` / `mp6600lgr-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [MONOLITHIC POWER SYSTEMS INC. datasheet, copy hosted by LCSC](docs/mp6600lgr-z-datasheet.pdf) (21 pp, sha256 `5d477fc1c0631eaa`, retrieved 2026-11-21)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mp6600lgr-z-datasheet.pdf)