Generated by kicad-footprint-generator · KiCad file format 20260206
MP4657BGS-Z
Monolithic Power Systems · LED Drivers · SOIC-16
MP4657BGS-Z from Monolithic Power Systems, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SYNC | input | Synchronization input connected to the flyback secondary winding through a voltage divider; its falling edge synchronizes the gate signal turning off (absolute maximum -6.5V to +6V). |
| 2 | OPT | output | Optocoupler drive output that outputs the compensation signal to control the flyback through an external optocoupler (absolute maximum -0.3V to +5V). |
| 3 | VFB | input | System voltage feedback input connected to VSYS through a voltage divider (VSYS = 1.2V x (RVFBH+RVFBL)/RVFBL), with system OVP triggered when VFB exceeds VREF by 24%. |
| 4 | DCOMP | passive | Compensation pin for the system voltage loop, controlling the external N-channel MOSFET duty when PWM is effective and the flyback stage with a differential gain when PWM is ineffective. |
| 5 | ICOMP | passive | Compensation pin for the LED driver loop that controls the flyback power stage when PWM is effective and holds its voltage when PWM is ineffective. |
| 6 | OVP | input | LED stage over-voltage protection input connected to the LED voltage through a voltage divider, with a threshold of about 2.4V for LED open protection and a latch-off above 3V. |
| 7 | LED1 | input | LED string 1 cathode, rated -0.3V to +80V. |
| 8 | LED2 | input | LED string 2 cathode, rated -0.3V to +80V. |
| 9 | GND | power_in | Ground. |
| 10 | LED4 | input | LED string 4 cathode, rated -0.3V to +80V. |
| 11 | LED3 | input | LED string 3 cathode, rated -0.3V to +80V. |
| 12 | ISET/FAULT | bidirectional | LED current setting pin (resistor to ground sets ILED, pin outputs 1.6V) that is also pulled low when a fault occurs. |
| 13 | ADIMP/PWM | input | Dimming signal input: a pulse above 5kHz gives analog dimming and a pulse below 5kHz gives PWM dimming. |
| 14 | VIN/SOURCE | power_in | Power supply input (4V to 16V recommended, -0.3V to +18V absolute maximum) that is also the reference for the gate signal. |
| 15 | VDRV | power_in | Gate driver supply (up to 53V referred to GND), bypassed to VIN/SOURCE with a ceramic capacitor (1µF recommended). |
| 16 | GATE | output | Gate driver output for the external N-channel MOSFET, referred to VIN/SOURCE and limited below 6V relative to VIN/SOURCE. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | SOIC-16 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN supply range | 4 | 16 | V | VIN = 13V, TJ = 25°C | 6 | ||
| VIN UVLO | VUVLO_VIN | 3.3 | 3.6 | 3.9 | V | 6 | |
| VDRV voltage range | VDRV | 6.5 | 48 | V | Refer to GND | 6 | |
| VDRV UVLO | 5.3 | 5.8 | 6.3 | V | VIN = 5V | 6 | |
| Reference voltage | VREF_VFB | 1.182 | 1.2 | 1.218 | V | 7 | |
| LED OVP threshold | VTH_OVP | 2.25 | 2.4 | 2.55 | V | 8 | |
| ISET voltage | VISET | 1.53 | 1.58 | 1.63 | V | 8 | |
| LEDx average current | ILED | -1.5 | 50 | 1.5 | mA | RISET = 320kΩ (trim), 50mA; tolerance in % | 8 |
| LEDx average current, 40% dimming | ILED | -3 | 19.2 | 3 | mA | 40% dimming, 20mA; tolerance in % | 8 |
| Current matching | 0.3 | 2 | % | ILED = 50mA | 8 | ||
| Current matching (40%) | 0.6 | 2.5 | % | ILED = 20mA (40%) | 8 | ||
| Analog dimming input frequency range | 5 | 100 | kHz | 6 | |||
| SYNC input frequency range | 20 | 350 | kHz | 6 | |||
| ADIMP/PWM logic high | VADIMP_HI | 1.5 | 6 | V | 6 | ||
| Quiescent current | IQ | 0.5 | mA | PWM = 0, GATE = high, VIN = 5V, no load | 6 | ||
| VIN UVLO hysteresis | VHYS_UVLO_VIN | 350 | mV | 6 | |||
| ADIMP/PWM logic low | VADIMP_LO | 0.7 | V | 6 | |||
| Thermal protection threshold | 150 | °C | Rising edge | 8 | |||
| VIN/SOURCE | -0.3 | 18 | V | 5 | |||
| VDRV | -0.3 | 53 | V | 5 | |||
| LEDx | -0.3 | 80 | V | 5 | |||
| GATE - VIN/SOURCE | -0.3 | 12 | V | 5 | |||
| SYNC | -6.5 | 6 | V | 5 | |||
| OPT | -0.3 | 5 | V | 5 | |||
| Other pins | -0.3 | 6.5 | V | 5 | |||
| Junction temperature | TJ | 150 | °C | 5 | |||
| Storage temperature | -65 | 150 | °C | 5 | |||
| Operating frequency | 20 | 350 | kHz | 5 | |||
| ESD HBM | -2000 | 2000 | V | Human body model | 5 | ||
| ESD CDM | -1500 | 1500 | V | Charged device model | 5 | ||
| Supply voltage | VIN | 4 | 16 | V | 5 | ||
| Operating frequency | 20 | 350 | kHz | 5 | |||
| Operating junction temperature | TJ | -40 | 125 | °C | 5 | ||
| Junction-to-ambient thermal resistance | θJA | 80 | °C/W | SOIC-16, JESD51-7 4-layer PCB | 5 | ||
| Junction-to-case thermal resistance | θJC | 35 | °C/W | SOIC-16, JESD51-7 4-layer PCB | 5 |
CAD (KiCad official)
- Symbol:
MP4657BGS-Z - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files:
mp4657bgs-z-etched.step/mp4657bgs-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp4657bgs-z.step/mp4657bgs-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (23 pp, sha256
6718f193e51c96bc, retrieved 2026-10-31, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).