main
Ray
Publish 0.1.0
0d07ae0
MP4059GS-Z
Monolithic Power Systems · LED Drivers · SOIC-8
MP4059GS-Z from Monolithic Power Systems, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | D | passive | Internal low-side main MOSFET drain, connected to the source of the external high-side MOSFET and to VCC through an internal diode and JFET for the VCC charging circuit, with a low-side MOSFET drain-to-source rating of -0.7V to 28V. |
| 2 | S | passive | Internal low-side main MOSFET source, with a sense resistor from S to GND for MOSFET current sensing; in CV mode it provides current limit (0.38V to 0.5V, 0.45V typical) and blanks for 450ns. |
| 3 | COMP | passive | Loop compensation for both CC and CV modes, where a compensation network is connected to stabilize the loop and COMP is clamped between 1.21V typical (low) and 2.65V typical (CV upper clamp). |
| 4 | ZCD | input | Zero-current detection input fed from a resistor divider between the auxiliary winding and GND, rated -0.3V to 6.5V, that detects over-voltage (4.5V threshold in CC) and brown-out (0.2V threshold during turn-on). |
| 5 | GND | power_in | Ground, serving as the current return for the control signal and the gate-drive signal, and to be kept separate from power GND and joined at a single point per the layout guidance. |
| 6 | DIM | input | Dimming input for an external PWM signal, where a low level (<0.3V) forces CV operation and the PWM amplitude should be higher than 1.5V. |
| 7 | VCC | power_in | Power supply input with a recommended operating range of 6V to 27V and an absolute maximum of 28V. |
| 8 | CS | input | Current sense input, where primary-side real-current control in CC mode is calculated via CS and line regulation can be compensated by a resistor from the line bus to CS. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | SOIC-8 |
| Category | LED Drivers |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating range VCC | VCC | 6 | 27 | V | After turn on | 4 | |
| VCC LFM level: LFM is triggered | VCCLFM | 7.95 | 8.25 | 8.5 | V | VCC falling edge | 4 |
| VCC regulate value at CV | VCCregulate | 7.1 | 7.5 | 7.9 | V | 4 | |
| VCC upper level: internal charging stops and IC turns on | VCCH | 10 | 10.5 | 11 | V | VCC rising edge | 4 |
| VCC lower level: internal charging circuit triggers | VCCL | 5.2 | 5.5 | 5.8 | V | VCC falling edge | 4 |
| VCC charging current from D | ID-charge | 3.7 | 5.7 | 7.2 | mA | VD = 16V, VCC = 10.5V | 4 |
| Operating current, CC operation | Ioperating | 370 | 440 | 620 | µA | Switch frequency is 60kHz, CC operation | 4 |
| Operating current under fault condition | Ifault | 205 | 265 | 360 | µA | Fault condition, IC latch, VCC = 15V | 4 |
| Pull-down current during UVLO | Ipull_down_UVLO | 0.85 | 1.25 | 1.8 | mA | VCC = 5V | 4 |
| DIM high level | Vdim_H | 1.08 | 1.2 | 1.33 | V | 4 | |
| DIM low level | Vdim_L | 0.26 | 0.3 | 0.33 | V | 4 | |
| Maximum DIM detect time, to determine the frequency of PWM dimming signal | tdim_detect | 8 | 9.4 | 12 | ms | PWM dimming frequency should be higher than 200Hz | 4 |
| Feedback voltage | VFB | 0.186 | 0.193 | 0.2 | V | 4 | |
| Max source current | ICOMP+ | 50 | µA | CC | 4 | ||
| Max sink current | ICOMP- | -200 | µA | 4 | |||
| Upper clamp voltage for CV | VCOMP_H_CV | 2.5 | 2.65 | 2.8 | V | 4 | |
| Lower clamp voltage | VCOMP_L | 1.15 | 1.21 | 1.27 | V | 4 | |
| Comp voltage where min-off time changes | VCOMP_MID | 1.3 | 1.39 | 1.47 | V | 4 | |
| Slope rate of normal operation | α | 0.24 | 0.28 | 0.3 | V/µs | 5 | |
| Minimum on time (CV) | Tmin_ON_time | 310 | 480 | 620 | ns | CV | 5 |
| Minimum on time (CC) | Tmin_ON_time | 900 | 1100 | 1400 | ns | CC | 5 |
| Bias current of ZCD | Ibias_ZCD | 255 | 315 | 355 | μA | During turn on | 5 |
| Brown-out protection threshold | Vbrown out | 0.16 | 0.185 | 0.21 | V | 5 | |
| Brown-out detection time | Tbrown out | 11 | 18.5 | 33 | ms | 5 | |
| Zero-current detect threshold | VZCD_T | 0.265 | 0.29 | 0.32 | V | VZCD falling edge | 5 |
| Zero-current hysteresis for CV | VZCD_hys | 0.26 | 0.3 | 0.34 | V | 5 | |
| Zero-current hysteresis for CC | VZCD_hys | 0.56 | 0.6 | 0.64 | V | 5 | |
| ZCD blanking time (CC) | tLEB_ZCD | 1.2 | 1.6 | 2 | μs | CC, after turn off, Vs_peak > 0.15V | 5 |
| ZCD blanking time (CC and CV) | tLEB_ZCD | 0.6 | 0.8 | 1.1 | μs | CC and CV, after turn off, Vs_peak < 0.15V | 5 |
| Over-voltage blanking time (CC) | tLEB_OVP | 1.2 | 1.6 | 2 | μs | CC, after turn off, Vs_peak > 0.15V | 5 |
| Over-voltage blanking time (CC and CV) | tLEB_OVP | 0.6 | 0.8 | 1.1 | μs | CC and CV, after turn off, Vs_peak < 0.15V | 5 |
| Over-voltage threshold | VZCD_OVP | 4.7 | 4.9 | 5.2 | V | 1.6μs delay after turn-off | 5 |
| Continue drain current | ID_D_VCC | 9.5 | 13.5 | 18.5 | mA | 5 | |
| Minimum off time in CC mode | Tmin_OFF_CC | 4.4 | 5 | 6.2 | µs | 5 | |
| Maximum min off time depending on COMP | Tmax_OFF_CC | 165 | 210 | 270 | µs | COMP = VCOMP_L | 5 |
| Start timer period | tSTART | 150 | 175 | 215 | µs | ZCD not detected in CC | 6 |
| CV mode current limit | Vcv_limit | 0.38 | 0.45 | 0.5 | V | With S pin blanking 450ns | 6 |
| CC mode current limit | VCC_limit | 1.4 | 1.47 | 1.55 | V | With S pin blanking 450ns | 6 |
| CV mode current limit foldback | Vcv_limit_foldback | 0.15 | 0.2 | 0.235 | V | With S pin blanking 450ns | 6 |
| Primary over-current protection | Vprimary_OCP | 1.9 | 2 | 2.1 | V | With S pin blanking 350ns | 6 |
| Leading edge blanking time | Tblank_S | 310 | 480 | 620 | ns | 6 | |
| Supply voltage (VCC) | VCC | -0.3 | 28 | V | 3 | ||
| ZCD | -0.3 | 6.5 | V | 3 | |||
| Low-side MOSFET drain-to-source voltage | -0.7 | 28 | V | 3 | |||
| All other pins | -0.3 | 6.5 | V | 3 | |||
| Continuous power dissipation (SOIC-8) | 1.3 | W | TA = 25°C | 3 | |||
| Junction temperature | 150 | °C | 3 | ||||
| Lead temperature | 260 | °C | 3 | ||||
| Storage temperature | -65 | 150 | °C | 3 | |||
| Supply voltage (VCC) | VCC | 6 | 27 | V | 3 | ||
| Operating junction temp. (TJ) | TJ | -40 | 125 | °C | 3 | ||
| Thermal resistance SOIC-8 junction-to-ambient | θJA | 96 | °C/W | JESD51-7, 4-layer PCB | 3 | ||
| Thermal resistance SOIC-8 junction-to-case | θJC | 45 | °C/W | JESD51-7, 4-layer PCB | 3 |
CAD (KiCad official)
- Symbol:
MP4059GS-Z - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
mp4059gs-z-etched.step/mp4059gs-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp4059gs-z.step/mp4059gs-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (21 pp, sha256
b86541f2fff2cf74, retrieved 2026-10-31, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MP4059GS-Z
**Monolithic Power Systems** · LED Drivers · SOIC-8
MP4059GS-Z from Monolithic Power Systems, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | D | passive | Internal low-side main MOSFET drain, connected to the source of the external high-side MOSFET and to VCC through an internal diode and JFET for the VCC charging circuit, with a low-side MOSFET drain-to-source rating of -0.7V to 28V. |
| 2 | S | passive | Internal low-side main MOSFET source, with a sense resistor from S to GND for MOSFET current sensing; in CV mode it provides current limit (0.38V to 0.5V, 0.45V typical) and blanks for 450ns. |
| 3 | COMP | passive | Loop compensation for both CC and CV modes, where a compensation network is connected to stabilize the loop and COMP is clamped between 1.21V typical (low) and 2.65V typical (CV upper clamp). |
| 4 | ZCD | input | Zero-current detection input fed from a resistor divider between the auxiliary winding and GND, rated -0.3V to 6.5V, that detects over-voltage (4.5V threshold in CC) and brown-out (0.2V threshold during turn-on). |
| 5 | GND | power_in | Ground, serving as the current return for the control signal and the gate-drive signal, and to be kept separate from power GND and joined at a single point per the layout guidance. |
| 6 | DIM | input | Dimming input for an external PWM signal, where a low level (<0.3V) forces CV operation and the PWM amplitude should be higher than 1.5V. |
| 7 | VCC | power_in | Power supply input with a recommended operating range of 6V to 27V and an absolute maximum of 28V. |
| 8 | CS | input | Current sense input, where primary-side real-current control in CC mode is calculated via CS and line regulation can be compensated by a resistor from the line bus to CS. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | SOIC-8 |
| Category | LED Drivers |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating range VCC | VCC | 6 | | 27 | V | After turn on | 4 |
| VCC LFM level: LFM is triggered | VCCLFM | 7.95 | 8.25 | 8.5 | V | VCC falling edge | 4 |
| VCC regulate value at CV | VCCregulate | 7.1 | 7.5 | 7.9 | V | | 4 |
| VCC upper level: internal charging stops and IC turns on | VCCH | 10 | 10.5 | 11 | V | VCC rising edge | 4 |
| VCC lower level: internal charging circuit triggers | VCCL | 5.2 | 5.5 | 5.8 | V | VCC falling edge | 4 |
| VCC charging current from D | ID-charge | 3.7 | 5.7 | 7.2 | mA | VD = 16V, VCC = 10.5V | 4 |
| Operating current, CC operation | Ioperating | 370 | 440 | 620 | µA | Switch frequency is 60kHz, CC operation | 4 |
| Operating current under fault condition | Ifault | 205 | 265 | 360 | µA | Fault condition, IC latch, VCC = 15V | 4 |
| Pull-down current during UVLO | Ipull_down_UVLO | 0.85 | 1.25 | 1.8 | mA | VCC = 5V | 4 |
| DIM high level | Vdim_H | 1.08 | 1.2 | 1.33 | V | | 4 |
| DIM low level | Vdim_L | 0.26 | 0.3 | 0.33 | V | | 4 |
| Maximum DIM detect time, to determine the frequency of PWM dimming signal | tdim_detect | 8 | 9.4 | 12 | ms | PWM dimming frequency should be higher than 200Hz | 4 |
| Feedback voltage | VFB | 0.186 | 0.193 | 0.2 | V | | 4 |
| Max source current | ICOMP+ | | | 50 | µA | CC | 4 |
| Max sink current | ICOMP- | | | -200 | µA | | 4 |
| Upper clamp voltage for CV | VCOMP_H_CV | 2.5 | 2.65 | 2.8 | V | | 4 |
| Lower clamp voltage | VCOMP_L | 1.15 | 1.21 | 1.27 | V | | 4 |
| Comp voltage where min-off time changes | VCOMP_MID | 1.3 | 1.39 | 1.47 | V | | 4 |
| Slope rate of normal operation | α | 0.24 | 0.28 | 0.3 | V/µs | | 5 |
| Minimum on time (CV) | Tmin_ON_time | 310 | 480 | 620 | ns | CV | 5 |
| Minimum on time (CC) | Tmin_ON_time | 900 | 1100 | 1400 | ns | CC | 5 |
| Bias current of ZCD | Ibias_ZCD | 255 | 315 | 355 | μA | During turn on | 5 |
| Brown-out protection threshold | Vbrown out | 0.16 | 0.185 | 0.21 | V | | 5 |
| Brown-out detection time | Tbrown out | 11 | 18.5 | 33 | ms | | 5 |
| Zero-current detect threshold | VZCD_T | 0.265 | 0.29 | 0.32 | V | VZCD falling edge | 5 |
| Zero-current hysteresis for CV | VZCD_hys | 0.26 | 0.3 | 0.34 | V | | 5 |
| Zero-current hysteresis for CC | VZCD_hys | 0.56 | 0.6 | 0.64 | V | | 5 |
| ZCD blanking time (CC) | tLEB_ZCD | 1.2 | 1.6 | 2 | μs | CC, after turn off, Vs_peak > 0.15V | 5 |
| ZCD blanking time (CC and CV) | tLEB_ZCD | 0.6 | 0.8 | 1.1 | μs | CC and CV, after turn off, Vs_peak < 0.15V | 5 |
| Over-voltage blanking time (CC) | tLEB_OVP | 1.2 | 1.6 | 2 | μs | CC, after turn off, Vs_peak > 0.15V | 5 |
| Over-voltage blanking time (CC and CV) | tLEB_OVP | 0.6 | 0.8 | 1.1 | μs | CC and CV, after turn off, Vs_peak < 0.15V | 5 |
| Over-voltage threshold | VZCD_OVP | 4.7 | 4.9 | 5.2 | V | 1.6μs delay after turn-off | 5 |
| Continue drain current | ID_D_VCC | 9.5 | 13.5 | 18.5 | mA | | 5 |
| Minimum off time in CC mode | Tmin_OFF_CC | 4.4 | 5 | 6.2 | µs | | 5 |
| Maximum min off time depending on COMP | Tmax_OFF_CC | 165 | 210 | 270 | µs | COMP = VCOMP_L | 5 |
| Start timer period | tSTART | 150 | 175 | 215 | µs | ZCD not detected in CC | 6 |
| CV mode current limit | Vcv_limit | 0.38 | 0.45 | 0.5 | V | With S pin blanking 450ns | 6 |
| CC mode current limit | VCC_limit | 1.4 | 1.47 | 1.55 | V | With S pin blanking 450ns | 6 |
| CV mode current limit foldback | Vcv_limit_foldback | 0.15 | 0.2 | 0.235 | V | With S pin blanking 450ns | 6 |
| Primary over-current protection | Vprimary_OCP | 1.9 | 2 | 2.1 | V | With S pin blanking 350ns | 6 |
| Leading edge blanking time | Tblank_S | 310 | 480 | 620 | ns | | 6 |
| Supply voltage (VCC) | VCC | -0.3 | | 28 | V | | 3 |
| ZCD | | -0.3 | | 6.5 | V | | 3 |
| Low-side MOSFET drain-to-source voltage | | -0.7 | | 28 | V | | 3 |
| All other pins | | -0.3 | | 6.5 | V | | 3 |
| Continuous power dissipation (SOIC-8) | | | | 1.3 | W | TA = 25°C | 3 |
| Junction temperature | | | | 150 | °C | | 3 |
| Lead temperature | | | | 260 | °C | | 3 |
| Storage temperature | | -65 | | 150 | °C | | 3 |
| Supply voltage (VCC) | VCC | 6 | | 27 | V | | 3 |
| Operating junction temp. (TJ) | TJ | -40 | | 125 | °C | | 3 |
| Thermal resistance SOIC-8 junction-to-ambient | θJA | | 96 | | °C/W | JESD51-7, 4-layer PCB | 3 |
| Thermal resistance SOIC-8 junction-to-case | θJC | | 45 | | °C/W | JESD51-7, 4-layer PCB | 3 |
## CAD (KiCad official)
- Symbol: `MP4059GS-Z`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files: `mp4059gs-z-etched.step` / `mp4059gs-z-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mp4059gs-z.step` / `mp4059gs-z.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Monolithic Power Systems datasheet](docs/mp4059gs-z-datasheet.pdf) (21 pp, sha256 `b86541f2fff2cf74`, retrieved 2026-10-31, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mp4059gs-z-datasheet.pdf)