main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers mp4059gs-z: viewers · Ray
mp4059gs-z-etched.glb Publish 0.1.0 · Ray
mp4059gs-z-etched.step mp4059gs-z: factory component page (tier=lcsc) · Ray
mp4059gs-z-hero.glb mp4059gs-z: hero GLB from the etched model (keeps the MPN mark) · Ray
mp4059gs-z-hero.overlay.json Publish 0.1.0 · Ray
mp4059gs-z.glb Publish 0.1.0 · Ray
mp4059gs-z.kicad_mod Publish 0.1.0 · Ray
mp4059gs-z.kicad_sym Publish 0.1.0 · Ray
mp4059gs-z.lbr Publish 0.1.0 · Ray
mp4059gs-z.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier lcsc, 8 pins · Ray

MP4059GS-Z

Monolithic Power Systems · LED Drivers · SOIC-8

MP4059GS-Z from Monolithic Power Systems, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 D passive Internal low-side main MOSFET drain, connected to the source of the external high-side MOSFET and to VCC through an internal diode and JFET for the VCC charging circuit, with a low-side MOSFET drain-to-source rating of -0.7V to 28V.
2 S passive Internal low-side main MOSFET source, with a sense resistor from S to GND for MOSFET current sensing; in CV mode it provides current limit (0.38V to 0.5V, 0.45V typical) and blanks for 450ns.
3 COMP passive Loop compensation for both CC and CV modes, where a compensation network is connected to stabilize the loop and COMP is clamped between 1.21V typical (low) and 2.65V typical (CV upper clamp).
4 ZCD input Zero-current detection input fed from a resistor divider between the auxiliary winding and GND, rated -0.3V to 6.5V, that detects over-voltage (4.5V threshold in CC) and brown-out (0.2V threshold during turn-on).
5 GND power_in Ground, serving as the current return for the control signal and the gate-drive signal, and to be kept separate from power GND and joined at a single point per the layout guidance.
6 DIM input Dimming input for an external PWM signal, where a low level (<0.3V) forces CV operation and the PWM amplitude should be higher than 1.5V.
7 VCC power_in Power supply input with a recommended operating range of 6V to 27V and an absolute maximum of 28V.
8 CS input Current sense input, where primary-side real-current control in CC mode is calculated via CS and line regulation can be compensated by a resistor from the line bus to CS.

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package SOIC-8
Category LED Drivers
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operating range VCC VCC 6 27 V After turn on 4
VCC LFM level: LFM is triggered VCCLFM 7.95 8.25 8.5 V VCC falling edge 4
VCC regulate value at CV VCCregulate 7.1 7.5 7.9 V 4
VCC upper level: internal charging stops and IC turns on VCCH 10 10.5 11 V VCC rising edge 4
VCC lower level: internal charging circuit triggers VCCL 5.2 5.5 5.8 V VCC falling edge 4
VCC charging current from D ID-charge 3.7 5.7 7.2 mA VD = 16V, VCC = 10.5V 4
Operating current, CC operation Ioperating 370 440 620 µA Switch frequency is 60kHz, CC operation 4
Operating current under fault condition Ifault 205 265 360 µA Fault condition, IC latch, VCC = 15V 4
Pull-down current during UVLO Ipull_down_UVLO 0.85 1.25 1.8 mA VCC = 5V 4
DIM high level Vdim_H 1.08 1.2 1.33 V 4
DIM low level Vdim_L 0.26 0.3 0.33 V 4
Maximum DIM detect time, to determine the frequency of PWM dimming signal tdim_detect 8 9.4 12 ms PWM dimming frequency should be higher than 200Hz 4
Feedback voltage VFB 0.186 0.193 0.2 V 4
Max source current ICOMP+ 50 µA CC 4
Max sink current ICOMP- -200 µA 4
Upper clamp voltage for CV VCOMP_H_CV 2.5 2.65 2.8 V 4
Lower clamp voltage VCOMP_L 1.15 1.21 1.27 V 4
Comp voltage where min-off time changes VCOMP_MID 1.3 1.39 1.47 V 4
Slope rate of normal operation α 0.24 0.28 0.3 V/µs 5
Minimum on time (CV) Tmin_ON_time 310 480 620 ns CV 5
Minimum on time (CC) Tmin_ON_time 900 1100 1400 ns CC 5
Bias current of ZCD Ibias_ZCD 255 315 355 μA During turn on 5
Brown-out protection threshold Vbrown out 0.16 0.185 0.21 V 5
Brown-out detection time Tbrown out 11 18.5 33 ms 5
Zero-current detect threshold VZCD_T 0.265 0.29 0.32 V VZCD falling edge 5
Zero-current hysteresis for CV VZCD_hys 0.26 0.3 0.34 V 5
Zero-current hysteresis for CC VZCD_hys 0.56 0.6 0.64 V 5
ZCD blanking time (CC) tLEB_ZCD 1.2 1.6 2 μs CC, after turn off, Vs_peak > 0.15V 5
ZCD blanking time (CC and CV) tLEB_ZCD 0.6 0.8 1.1 μs CC and CV, after turn off, Vs_peak < 0.15V 5
Over-voltage blanking time (CC) tLEB_OVP 1.2 1.6 2 μs CC, after turn off, Vs_peak > 0.15V 5
Over-voltage blanking time (CC and CV) tLEB_OVP 0.6 0.8 1.1 μs CC and CV, after turn off, Vs_peak < 0.15V 5
Over-voltage threshold VZCD_OVP 4.7 4.9 5.2 V 1.6μs delay after turn-off 5
Continue drain current ID_D_VCC 9.5 13.5 18.5 mA 5
Minimum off time in CC mode Tmin_OFF_CC 4.4 5 6.2 µs 5
Maximum min off time depending on COMP Tmax_OFF_CC 165 210 270 µs COMP = VCOMP_L 5
Start timer period tSTART 150 175 215 µs ZCD not detected in CC 6
CV mode current limit Vcv_limit 0.38 0.45 0.5 V With S pin blanking 450ns 6
CC mode current limit VCC_limit 1.4 1.47 1.55 V With S pin blanking 450ns 6
CV mode current limit foldback Vcv_limit_foldback 0.15 0.2 0.235 V With S pin blanking 450ns 6
Primary over-current protection Vprimary_OCP 1.9 2 2.1 V With S pin blanking 350ns 6
Leading edge blanking time Tblank_S 310 480 620 ns 6
Supply voltage (VCC) VCC -0.3 28 V 3
ZCD -0.3 6.5 V 3
Low-side MOSFET drain-to-source voltage -0.7 28 V 3
All other pins -0.3 6.5 V 3
Continuous power dissipation (SOIC-8) 1.3 W TA = 25°C 3
Junction temperature 150 °C 3
Lead temperature 260 °C 3
Storage temperature -65 150 °C 3
Supply voltage (VCC) VCC 6 27 V 3
Operating junction temp. (TJ) TJ -40 125 °C 3
Thermal resistance SOIC-8 junction-to-ambient θJA 96 °C/W JESD51-7, 4-layer PCB 3
Thermal resistance SOIC-8 junction-to-case θJC 45 °C/W JESD51-7, 4-layer PCB 3

CAD (KiCad official)

  • Symbol: MP4059GS-Z
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: mp4059gs-z-etched.step / mp4059gs-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mp4059gs-z.step / mp4059gs-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (21 pp, sha256 b86541f2fff2cf74, retrieved 2026-10-31, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF