main
History Download
Ray Publish 0.1.0 a412d45

MP2151GTF-Z

Monolithic Power Systems · DC-DC Converters · SOT-563

MP2151GTF-Z from Monolithic Power Systems, in a SOT-563. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Power ground for the converter.
2 SW output Output switching node and drain of the internal high-side P-channel MOSFET; connect the inductor to SW to complete the converter.
3 VIN power_in Supply input for the regulator, operating from +2.5V to +5.5V (unregulated), and must be decoupled with a capacitor to prevent large voltage spikes at the input.
4 EN input On/off control: the device is enabled when EN is pulled above 1.2V and disabled when EN is low (0.4V max) or left floating, with an internal 1MΩ resistor to ground.
5 FB input Feedback input for the adjustable version; an external resistor divider from the output to GND tapped at FB sets the output voltage, which can be regulated as low as 0.6V.
6 OUT power_out Output voltage rail and sense input for the output voltage; connect the load to OUT and use an output capacitor to reduce output ripple.

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package SOT-563
Category Power Management
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN range 2.5 5.5 V 5
Feedback voltage VFB 594 600 606 mV TJ = 25°C 5
Feedback voltage VFB 591 600 609 mV TJ = -40°C to +125°C 5
Under-voltage lockout threshold rising 2.3 2.45 V threshold rising 5
Under-voltage lockout threshold hysteresis 200 mV 5
Output over-voltage threshold VOVP 110 115 120 % VFB 6
Feedback current IFB 50 100 nA VFB = 0.63V 5
ON time TON 180 220 260 ns VIN = 5V, VOUT = 1.2V 5
ON time TON 240 300 360 ns VIN = 3.6V, VOUT = 1.2V 5
Supply current (quiescent) (MP2151XX, adjustable) IQ 25 30 μA VEN = 2V, VFB = 0.63V, VIN = 5V, TJ = +25°C 6
Supply current (shutdown) 0 1 μA VEN = 0V, TJ = +25°C 6
Switch leakage 0 1 μA VEN = 0V, VIN = 6V, VSW = 0V and 6V, TJ = +25°C 5
Supply voltage (VIN) absolute maximum VIN 6.5 V 4
VSW VSW -0.3 6.5 V Transient under 10ns: -5V min, 10V max 4
All other pins -0.3 6.5 V 4
Junction temperature 150 °C 4
Lead temperature 260 °C 4
Continuous power dissipation 1.5 W TA = +25°C, SOT563 4
Storage temperature -65 150 °C 4
Supply voltage (VIN) recommended VIN 2.5 5.5 V 4
Operating junction temperature TJ -40 125 °C 4
P-FET switch on resistance RDSON_P 80 mΩ VIN = 5V 5
N-FET switch on resistance RDSON_N 50 mΩ VIN = 5V 5
P-FET peak current limit 1.8 A 5
ZCD 50 mA 5
Switching frequency fs 1100 kHz VOUT = 1.2V 5
Minimum off time TMIN-OFF 100 ns 5
Minimum on time TMIN-ON 60 ns 5
Soft-start time TSS-ON 0.5 ms VOUT rise from 10% to 90% 5
Maximum duty cycle 100 % 5
EN turn on delay 150 us EN on to SW active 6
EN input logic low voltage 0.4 V 6
EN input logic high voltage 1.2 V 6
Output discharge resistor RDIS 200 Ω VEN = 0V, VOUT = 1.2V 6
EN input current 1.2 μA VEN = 2V 6
EN input current 0 μA VEN = 0V 6
OVP delay 12 us 6
Vo OVP hysteresis VOVP_HYS 10 % VFB 6
Low-side current 1.5 A Current flow from SW to GND 6
Absolute VIN OVP 6.1 V After Vo OVP enable 6
Absolute VIN OVP hysteresis 400 mV 6
Thermal shutdown 160 °C Guaranteed by over-temperature correlation, not tested in production (note 7) 6
Thermal hysteresis 30 °C Guaranteed by over-temperature correlation, not tested in production (note 7) 6
Thermal resistance junction-to-ambient θJA 80 °C/W EV2151-TF-00A, 2-layer PCB, 63mmx63mm 4
Thermal resistance junction-to-case θJC 50 °C/W EV2151-TF-00A, 2-layer PCB, 63mmx63mm 4
Thermal resistance junction-to-ambient θJA 130 °C/W JESD51-7, 4-layer PCB 4
Thermal resistance junction-to-case θJC 60 °C/W JESD51-7, 4-layer PCB 4

CAD (KiCad official)

  • Symbol: MP2151GTF-Z
  • Footprint: Package_TO_SOT_SMD:SOT-563
  • 3D model: SOT-563 (KiCad packages3D, STEP)
  • 3D model files: mp2151gtf-z-etched.step / mp2151gtf-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mp2151gtf-z.step / mp2151gtf-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (21 pp, sha256 954e5859635278f7, retrieved 2026-10-28, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF