main
Ray
Publish 0.1.0
e2403a5
MIC5236-3.0YM
Microchip Tech · Linear Voltage Regulators (LDO) · SO-8
MIC5236-3.0YM from Microchip Tech, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | /ERR | output | Open-collector error output that is active low when the output is out of regulation due to insufficient input voltage or excessive load, and requires an external pull-up resistor (200k to 1MΩ suggested). |
| 2 | IN | power_in | Power supply input, specified for 2.3V to 30V continuous operation (absolute maximum -20V to +60V, with the +60V limited to ≤100ms and ≤1% duty cycle). |
| 3 | OUT | power_out | Regulated output, 3.0V for this fixed-voltage variant, which requires a 1.0µF output capacitor for stability. |
| 4 | EN | input | Enable input where logic low (VIL max 0.6V) shuts the regulator down and logic high (VIH min 2.0V) enables it. |
| 5 | GND | power_in | Ground; pins 5 through 8 are internally connected in common via the leadframe. |
| 6 | GND | power_in | Ground; pins 5 through 8 are internally connected in common via the leadframe. |
| 7 | GND | power_in | Ground; pins 5 through 8 are internally connected in common via the leadframe. |
| 8 | GND | power_in | Ground; pins 5 through 8 are internally connected in common via the leadframe. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SO-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage Accuracy | VOUT | -1 | 1 | % | variation from nominal VOUT; VIN = 6.0V; VEN = 2.0V; COUT = 4.7µF, IOUT = 100µA; TJ = 25°C | 3 | |
| Output Voltage Accuracy | VOUT | -2 | 2 | % | variation from nominal VOUT; VIN = 6.0V; VEN = 2.0V; COUT = 4.7µF, IOUT = 100µA; -40°C ≤ TJ ≤ +125°C (bold) | 3 | |
| Output Voltage Temperature Coefficient | ΔVOUT/ΔT | 50 | ppm/°C | Note 6 | 3 | ||
| Line Regulation | ΔVOUT/VOUT | 0.2 | 0.5 | % | VIN = VOUT + 1V to 30V | 3 | |
| Line Regulation | ΔVOUT/VOUT | 1 | % | VIN = VOUT + 1V to 30V | 3 | ||
| Load Regulation | ΔVOUT/VOUT | 0.15 | 0.3 | % | IOUT = 100µA to 50mA, Note 7 | 3 | |
| Load Regulation | ΔVOUT/VOUT | 0.5 | % | IOUT = 100µA to 50mA, Note 7 | 3 | ||
| Load Regulation | ΔVOUT/VOUT | 0.3 | 0.6 | % | IOUT = 100µA to 150mA, Note 7 | 3 | |
| Load Regulation | ΔVOUT/VOUT | 1 | % | IOUT = 100µA to 150mA, Note 7 | 3 | ||
| Dropout Voltage | ΔV | 50 | 100 | mV | IOUT = 100µA, Note 8 | 3 | |
| Dropout Voltage | ΔV | 230 | 400 | mV | IOUT = 50mA, Note 8 | 3 | |
| Dropout Voltage | ΔV | 300 | 500 | mV | IOUT = 150mA, Note 8 | 3 | |
| Ground Pin Current | IGND | 20 | 30 | µA | VEN ≥ 2.0V, IOUT = 100µA | 3 | |
| Ground Pin Current | IGND | 0.5 | 0.8 | mA | VEN ≥ 2.0V, IOUT = 50mA | 3 | |
| Ground Pin Current | IGND | 2.8 | 4 | mA | VEN ≥ 2.0V, IOUT = 150mA | 3 | |
| Ground Pin Current | IGND | 5 | mA | VEN ≥ 2.0V, IOUT = 150mA | 3 | ||
| Ground Pin Current in Shutdown | IGND(SHDN) | 0.1 | 1 | µA | VEN ≤ 0.6V, VIN = 30V | 3 | |
| Short Circuit Current | ISC | 260 | 350 | mA | VOUT = 0V | 3 | |
| Low Threshold /ERR | V/ERR | 90 | 94 | % | % of VOUT | 3 | |
| High Threshold /ERR | V/ERR | 95 | 98 | % | % of VOUT | 3 | |
| /ERR Output Low Voltage | VOL | 150 | 250 | mV | VIN = VOUT(nom), 0.12VOUT, IOL = 200µA | 3 | |
| /ERR Output Low Voltage | VOL | 400 | mV | VIN = VOUT(nom), 0.12VOUT, IOL = 200µA | 3 | ||
| /ERR Output Leakage | ILEAK | 0.1 | 1 | µA | VOH = 30V | 3 | |
| /ERR Output Leakage | ILEAK | 2 | µA | VOH = 30V | 3 | ||
| Enable Input Low Voltage | VIL | 0.6 | V | regulator off | 3 | ||
| Enable Input High Voltage | VIH | 2 | V | regulator on | 3 | ||
| Enable Input Current | IIN | 0.01 | 1 | µA | VEN = 0.6V, regulator off | 4 | |
| Enable Input Current | IIN | 2 | µA | VEN = 0.6V, regulator off | 4 | ||
| Enable Input Current | IIN | 0.15 | 1 | µA | VEN = 2.0V, regulator on | 4 | |
| Enable Input Current | IIN | 0.5 | 2.5 | µA | VEN = 30V, regulator on | 4 | |
| Enable Input Current | IIN | 5 | µA | VEN = 30V, regulator on | 4 | ||
| Supply Voltage (VIN) | VIN | 2.3 | 30 | V | 3 | ||
| Junction Temperature (TJ) | TJ | -40 | 125 | °C | 3 | ||
| Supply Voltage (VIN) | VIN | -20 | 60 | V | Note 3: ≤100ms duration, ≤1% duty cycle | 3 | |
| Junction Temperature (TJ) | TJ | 150 | °C | 3 | |||
| Storage Temperature (TS) | TS | -65 | 150 | °C | 3 | ||
| Lead Temperature | 260 | °C | soldering, 5 sec | 3 | |||
| Package Thermal Resistance SOIC | θJA | 63 | °C/W | SOIC (θJA) | 3 | ||
| Thermal Resistance Junction-to-Case, power SOIC-8 | θJC | 20 | °C/W | power SOIC-8, typical, from text | 10 |
CAD (KiCad official)
- Symbol:
MIC5236-3.0YM - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
mic5236-3-0ym-etched.step/mic5236-3-0ym-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic5236-3-0ym.step/mic5236-3-0ym.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (12 pp, sha256
dab9c0775d086119, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MIC5236-3.0YM
**Microchip Tech** · Linear Voltage Regulators (LDO) · SO-8
MIC5236-3.0YM from Microchip Tech, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | /ERR | output | Open-collector error output that is active low when the output is out of regulation due to insufficient input voltage or excessive load, and requires an external pull-up resistor (200k to 1MΩ suggested). |
| 2 | IN | power_in | Power supply input, specified for 2.3V to 30V continuous operation (absolute maximum -20V to +60V, with the +60V limited to ≤100ms and ≤1% duty cycle). |
| 3 | OUT | power_out | Regulated output, 3.0V for this fixed-voltage variant, which requires a 1.0µF output capacitor for stability. |
| 4 | EN | input | Enable input where logic low (VIL max 0.6V) shuts the regulator down and logic high (VIH min 2.0V) enables it. |
| 5 | GND | power_in | Ground; pins 5 through 8 are internally connected in common via the leadframe. |
| 6 | GND | power_in | Ground; pins 5 through 8 are internally connected in common via the leadframe. |
| 7 | GND | power_in | Ground; pins 5 through 8 are internally connected in common via the leadframe. |
| 8 | GND | power_in | Ground; pins 5 through 8 are internally connected in common via the leadframe. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SO-8 |
| Category | Power Supply Chip |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage Accuracy | VOUT | -1 | | 1 | % | variation from nominal VOUT; VIN = 6.0V; VEN = 2.0V; COUT = 4.7µF, IOUT = 100µA; TJ = 25°C | 3 |
| Output Voltage Accuracy | VOUT | -2 | | 2 | % | variation from nominal VOUT; VIN = 6.0V; VEN = 2.0V; COUT = 4.7µF, IOUT = 100µA; -40°C ≤ TJ ≤ +125°C (bold) | 3 |
| Output Voltage Temperature Coefficient | ΔVOUT/ΔT | | | 50 | ppm/°C | Note 6 | 3 |
| Line Regulation | ΔVOUT/VOUT | | 0.2 | 0.5 | % | VIN = VOUT + 1V to 30V | 3 |
| Line Regulation | ΔVOUT/VOUT | | | 1 | % | VIN = VOUT + 1V to 30V | 3 |
| Load Regulation | ΔVOUT/VOUT | | 0.15 | 0.3 | % | IOUT = 100µA to 50mA, Note 7 | 3 |
| Load Regulation | ΔVOUT/VOUT | | | 0.5 | % | IOUT = 100µA to 50mA, Note 7 | 3 |
| Load Regulation | ΔVOUT/VOUT | | 0.3 | 0.6 | % | IOUT = 100µA to 150mA, Note 7 | 3 |
| Load Regulation | ΔVOUT/VOUT | | | 1 | % | IOUT = 100µA to 150mA, Note 7 | 3 |
| Dropout Voltage | ΔV | | 50 | 100 | mV | IOUT = 100µA, Note 8 | 3 |
| Dropout Voltage | ΔV | | 230 | 400 | mV | IOUT = 50mA, Note 8 | 3 |
| Dropout Voltage | ΔV | | 300 | 500 | mV | IOUT = 150mA, Note 8 | 3 |
| Ground Pin Current | IGND | | 20 | 30 | µA | VEN ≥ 2.0V, IOUT = 100µA | 3 |
| Ground Pin Current | IGND | | 0.5 | 0.8 | mA | VEN ≥ 2.0V, IOUT = 50mA | 3 |
| Ground Pin Current | IGND | | 2.8 | 4 | mA | VEN ≥ 2.0V, IOUT = 150mA | 3 |
| Ground Pin Current | IGND | | | 5 | mA | VEN ≥ 2.0V, IOUT = 150mA | 3 |
| Ground Pin Current in Shutdown | IGND(SHDN) | | 0.1 | 1 | µA | VEN ≤ 0.6V, VIN = 30V | 3 |
| Short Circuit Current | ISC | | 260 | 350 | mA | VOUT = 0V | 3 |
| Low Threshold /ERR | V/ERR | | 90 | 94 | % | % of VOUT | 3 |
| High Threshold /ERR | V/ERR | | 95 | 98 | % | % of VOUT | 3 |
| /ERR Output Low Voltage | VOL | | 150 | 250 | mV | VIN = VOUT(nom), 0.12VOUT, IOL = 200µA | 3 |
| /ERR Output Low Voltage | VOL | | | 400 | mV | VIN = VOUT(nom), 0.12VOUT, IOL = 200µA | 3 |
| /ERR Output Leakage | ILEAK | | 0.1 | 1 | µA | VOH = 30V | 3 |
| /ERR Output Leakage | ILEAK | | | 2 | µA | VOH = 30V | 3 |
| Enable Input Low Voltage | VIL | | | 0.6 | V | regulator off | 3 |
| Enable Input High Voltage | VIH | 2 | | | V | regulator on | 3 |
| Enable Input Current | IIN | | 0.01 | 1 | µA | VEN = 0.6V, regulator off | 4 |
| Enable Input Current | IIN | | | 2 | µA | VEN = 0.6V, regulator off | 4 |
| Enable Input Current | IIN | | 0.15 | 1 | µA | VEN = 2.0V, regulator on | 4 |
| Enable Input Current | IIN | | 0.5 | 2.5 | µA | VEN = 30V, regulator on | 4 |
| Enable Input Current | IIN | | | 5 | µA | VEN = 30V, regulator on | 4 |
| Supply Voltage (VIN) | VIN | 2.3 | | 30 | V | | 3 |
| Junction Temperature (TJ) | TJ | -40 | | 125 | °C | | 3 |
| Supply Voltage (VIN) | VIN | -20 | | 60 | V | Note 3: ≤100ms duration, ≤1% duty cycle | 3 |
| Junction Temperature (TJ) | TJ | | | 150 | °C | | 3 |
| Storage Temperature (TS) | TS | -65 | | 150 | °C | | 3 |
| Lead Temperature | | | | 260 | °C | soldering, 5 sec | 3 |
| Package Thermal Resistance SOIC | θJA | | 63 | | °C/W | SOIC (θJA) | 3 |
| Thermal Resistance Junction-to-Case, power SOIC-8 | θJC | | 20 | | °C/W | power SOIC-8, typical, from text | 10 |
## CAD (KiCad official)
- Symbol: `MIC5236-3.0YM`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files: `mic5236-3-0ym-etched.step` / `mic5236-3-0ym-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mic5236-3-0ym.step` / `mic5236-3-0ym.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](https://ww1.microchip.com/downloads/en/DeviceDoc/mic5236.pdf) (12 pp, sha256 `dab9c0775d086119`, retrieved 2026-11-17, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mic5236-3-0ym-datasheet.pdf)