main
Ray Publish 0.1.0 a0426cf

MIC5216-3.3YMM

Microchip Tech · Linear Voltage Regulators (LDO) · MSOP-8

MIC5216-3.3YMM from Microchip Tech, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 EN input CMOS-compatible enable input: logic high (above 2V) enables the regulator, while logic low or open shuts it down, with EN limited to 0V to VIN.
2 IN power_in Supply input with an operating range of 2.5V to 12V and an absolute maximum of -20V to +20V; a 1µF capacitor to GND is recommended if the wire to the filter capacitor exceeds 10 inches or a battery is the source.
3 OUT power_out Regulator output, which requires an output capacitor of at least 1µF to GND to prevent oscillation.
4 FLG output Open-collector error flag output that goes active low when the output is undervoltage by about 5% below nominal, and requires a pull-up resistor to the input when used.
5 GND power_in Ground; MSOP-8 pins 5 through 8 are internally connected to one another.
6 GND power_in Ground; MSOP-8 pins 5 through 8 are internally connected to one another.
7 GND power_in Ground; MSOP-8 pins 5 through 8 are internally connected to one another.
8 GND power_in Ground; MSOP-8 pins 5 through 8 are internally connected to one another.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package MSOP-8
Category Power Supply Chip
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Output Voltage Accuracy VO -1 1 % Variation from nominal VOUT; VIN=VOUT+1V, COUT=4.7µF, IOUT=100µA, TJ=25°C 4
Output Voltage Accuracy (bold, over temperature) VO -2 2 % Variation from nominal VOUT; bold values -40°C < TJ < +125°C 4
Output Voltage Temperature Coefficient ∆VO/∆T 40 ppm/°C Note 2 4
Line Regulation ∆VO/VO 0.009 0.05 %/V VIN = VOUT +1V to 12V 4
Line Regulation (bold, over temperature) ∆VO/VO 0.1 %/V VIN = VOUT +1V to 12V; bold values -40°C < TJ < +125°C 4
Load Regulation ∆VO/VO 0.05 0.5 % IOUT = 100µA to 150mA (Note 3) 4
Load Regulation (bold, over temperature) ∆VO/VO 0.7 % IOUT = 100µA to 150mA (Note 3); bold values -40°C < TJ < +125°C 4
Dropout Voltage VIN, VO 10 60 mV IOUT = 100µA; Note 4 4
Dropout Voltage (bold, over temperature) VIN, VO 80 mV IOUT = 100µA; Note 4; bold values -40°C < TJ < +125°C 4
Dropout Voltage VIN, VO 115 175 mV IOUT = 50mA; Note 4 4
Dropout Voltage (bold, over temperature) VIN, VO 250 mV IOUT = 50mA; Note 4; bold values -40°C < TJ < +125°C 4
Dropout Voltage VIN, VO 165 300 mV IOUT = 150mA; Note 4 4
Dropout Voltage (bold, over temperature) VIN, VO 400 mV IOUT = 150mA; Note 4; bold values -40°C < TJ < +125°C 4
Dropout Voltage VIN, VO 300 500 mV IOUT = 500mA; Note 4 4
Dropout Voltage (bold, over temperature) VIN, VO 600 mV IOUT = 500mA; Note 4; bold values -40°C < TJ < +125°C 4
Ground Pin Current (per regulator) IGND 80 130 µA VEN ≥ 3.0V, IOUT = 100µA; Notes 5, 6 4
Ground Pin Current (bold, over temperature) IGND 170 µA VEN ≥ 3.0V, IOUT = 100µA; Notes 5, 6; bold values -40°C < TJ < +125°C 4
Ground Pin Current (per regulator) IGND 350 650 µA VEN ≥ 3.0V, IOUT = 50mA; Notes 5, 6 4
Ground Pin Current (bold, over temperature) IGND 900 µA VEN ≥ 3.0V, IOUT = 50mA; Notes 5, 6; bold values -40°C < TJ < +125°C 4
Ground Pin Current (per regulator) IGND 1.8 2.5 mA VEN ≥ 3.0V, IOUT = 150mA; Notes 5, 6 4
Ground Pin Current (bold, over temperature) IGND 3 mA VEN ≥ 3.0V, IOUT = 150mA; Notes 5, 6; bold values -40°C < TJ < +125°C 4
Ground Pin Current (per regulator) IGND 8 20 mA VEN ≥ 3.0V, IOUT = 500mA; Notes 5, 6 4
Ground Pin Current (bold, over temperature) IGND 25 mA VEN ≥ 3.0V, IOUT = 500mA; Notes 5, 6; bold values -40°C < TJ < +125°C 4
Quiescent Current IGND 0.05 3 µA VEN ≤ 0.4V; Note 6 4
Quiescent Current IGND 0.1 8 µA VEN ≤ 0.18V; Note 6 4
Ripple Rejection PSRR 75 dB Frequency = 120Hz 4
Current Limit ILIMIT 700 1000 mA VOUT = 0V 4
Thermal Regulation ∆VO/∆PD 0.05 %/W Note 7 4
Output Noise eno 500 nV/√Hz IOUT = 50mA, COUT = 2.2µF 4
Enable Input Voltage (logic low) VENL 0.4 V VEN = logic low (regulator shutdown) 5
Enable Input Voltage (logic low, bold) VENL 0.18 V bold values -40°C < TJ < +125°C 5
Enable Input Voltage (logic high) VENH 2 V VEN = logic high (regulator enabled) 5
Error Flag Threshold VERR -2 -6 -10 % Undervoltage condition (below nominal); Note 8 5
Output Logic-Low Voltage VIL 0.2 0.4 V IL = 1mA, undervoltage condition 5
Flag Leakage Current IFL -1 0.1 1 µA Flag off, VFLAG = 0V to 12V 5
Supply Input Voltage (absolute maximum) VIN -20 20 V 4
Junction Temperature (absolute maximum) TJ -40 125 °C 4
Lead Temperature (soldering) 260 °C Soldering, 5 sec 4
Supply Input Voltage (operating) VIN 2.5 12 V 4
Enable Input Voltage (operating) VEN 0 V Upper limit VIN 4
Junction Temperature (operating) TJ -40 125 °C 4
Thermal Resistance, junction-to-ambient θJA 160 °C/W MM8 (MM) package, recommended minimum footprint 8
Thermal Resistance, junction-to-ambient θJA 70 °C/W MM8 (MM) package, 1 in² copper clad 8
Thermal Resistance, junction-to-case θJC 30 °C/W MM8 (MM) package 8

CAD (KiCad official)

  • Symbol: MIC5216-3.3YMM
  • Footprint: Package_SO:MSOP-8_3x3mm_P0.65mm
  • 3D model: MSOP-8 (KiCad packages3D, STEP)
  • 3D model files: mic5216-3-3ymm-etched.step / mic5216-3-3ymm-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mic5216-3-3ymm.step / mic5216-3-3ymm.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet, copy hosted by LCSC (13 pp, sha256 3f9486ced6f887d9, retrieved 2026-11-21)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF