Generated by kicad-footprint-generator · KiCad file format 20260206
MIC5216-3.3YMM
Microchip Tech · Linear Voltage Regulators (LDO) · MSOP-8
MIC5216-3.3YMM from Microchip Tech, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | CMOS-compatible enable input: logic high (above 2V) enables the regulator, while logic low or open shuts it down, with EN limited to 0V to VIN. |
| 2 | IN | power_in | Supply input with an operating range of 2.5V to 12V and an absolute maximum of -20V to +20V; a 1µF capacitor to GND is recommended if the wire to the filter capacitor exceeds 10 inches or a battery is the source. |
| 3 | OUT | power_out | Regulator output, which requires an output capacitor of at least 1µF to GND to prevent oscillation. |
| 4 | FLG | output | Open-collector error flag output that goes active low when the output is undervoltage by about 5% below nominal, and requires a pull-up resistor to the input when used. |
| 5 | GND | power_in | Ground; MSOP-8 pins 5 through 8 are internally connected to one another. |
| 6 | GND | power_in | Ground; MSOP-8 pins 5 through 8 are internally connected to one another. |
| 7 | GND | power_in | Ground; MSOP-8 pins 5 through 8 are internally connected to one another. |
| 8 | GND | power_in | Ground; MSOP-8 pins 5 through 8 are internally connected to one another. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage Accuracy | VO | -1 | 1 | % | Variation from nominal VOUT; VIN=VOUT+1V, COUT=4.7µF, IOUT=100µA, TJ=25°C | 4 | |
| Output Voltage Accuracy (bold, over temperature) | VO | -2 | 2 | % | Variation from nominal VOUT; bold values -40°C < TJ < +125°C | 4 | |
| Output Voltage Temperature Coefficient | ∆VO/∆T | 40 | ppm/°C | Note 2 | 4 | ||
| Line Regulation | ∆VO/VO | 0.009 | 0.05 | %/V | VIN = VOUT +1V to 12V | 4 | |
| Line Regulation (bold, over temperature) | ∆VO/VO | 0.1 | %/V | VIN = VOUT +1V to 12V; bold values -40°C < TJ < +125°C | 4 | ||
| Load Regulation | ∆VO/VO | 0.05 | 0.5 | % | IOUT = 100µA to 150mA (Note 3) | 4 | |
| Load Regulation (bold, over temperature) | ∆VO/VO | 0.7 | % | IOUT = 100µA to 150mA (Note 3); bold values -40°C < TJ < +125°C | 4 | ||
| Dropout Voltage | VIN, VO | 10 | 60 | mV | IOUT = 100µA; Note 4 | 4 | |
| Dropout Voltage (bold, over temperature) | VIN, VO | 80 | mV | IOUT = 100µA; Note 4; bold values -40°C < TJ < +125°C | 4 | ||
| Dropout Voltage | VIN, VO | 115 | 175 | mV | IOUT = 50mA; Note 4 | 4 | |
| Dropout Voltage (bold, over temperature) | VIN, VO | 250 | mV | IOUT = 50mA; Note 4; bold values -40°C < TJ < +125°C | 4 | ||
| Dropout Voltage | VIN, VO | 165 | 300 | mV | IOUT = 150mA; Note 4 | 4 | |
| Dropout Voltage (bold, over temperature) | VIN, VO | 400 | mV | IOUT = 150mA; Note 4; bold values -40°C < TJ < +125°C | 4 | ||
| Dropout Voltage | VIN, VO | 300 | 500 | mV | IOUT = 500mA; Note 4 | 4 | |
| Dropout Voltage (bold, over temperature) | VIN, VO | 600 | mV | IOUT = 500mA; Note 4; bold values -40°C < TJ < +125°C | 4 | ||
| Ground Pin Current (per regulator) | IGND | 80 | 130 | µA | VEN ≥ 3.0V, IOUT = 100µA; Notes 5, 6 | 4 | |
| Ground Pin Current (bold, over temperature) | IGND | 170 | µA | VEN ≥ 3.0V, IOUT = 100µA; Notes 5, 6; bold values -40°C < TJ < +125°C | 4 | ||
| Ground Pin Current (per regulator) | IGND | 350 | 650 | µA | VEN ≥ 3.0V, IOUT = 50mA; Notes 5, 6 | 4 | |
| Ground Pin Current (bold, over temperature) | IGND | 900 | µA | VEN ≥ 3.0V, IOUT = 50mA; Notes 5, 6; bold values -40°C < TJ < +125°C | 4 | ||
| Ground Pin Current (per regulator) | IGND | 1.8 | 2.5 | mA | VEN ≥ 3.0V, IOUT = 150mA; Notes 5, 6 | 4 | |
| Ground Pin Current (bold, over temperature) | IGND | 3 | mA | VEN ≥ 3.0V, IOUT = 150mA; Notes 5, 6; bold values -40°C < TJ < +125°C | 4 | ||
| Ground Pin Current (per regulator) | IGND | 8 | 20 | mA | VEN ≥ 3.0V, IOUT = 500mA; Notes 5, 6 | 4 | |
| Ground Pin Current (bold, over temperature) | IGND | 25 | mA | VEN ≥ 3.0V, IOUT = 500mA; Notes 5, 6; bold values -40°C < TJ < +125°C | 4 | ||
| Quiescent Current | IGND | 0.05 | 3 | µA | VEN ≤ 0.4V; Note 6 | 4 | |
| Quiescent Current | IGND | 0.1 | 8 | µA | VEN ≤ 0.18V; Note 6 | 4 | |
| Ripple Rejection | PSRR | 75 | dB | Frequency = 120Hz | 4 | ||
| Current Limit | ILIMIT | 700 | 1000 | mA | VOUT = 0V | 4 | |
| Thermal Regulation | ∆VO/∆PD | 0.05 | %/W | Note 7 | 4 | ||
| Output Noise | eno | 500 | nV/√Hz | IOUT = 50mA, COUT = 2.2µF | 4 | ||
| Enable Input Voltage (logic low) | VENL | 0.4 | V | VEN = logic low (regulator shutdown) | 5 | ||
| Enable Input Voltage (logic low, bold) | VENL | 0.18 | V | bold values -40°C < TJ < +125°C | 5 | ||
| Enable Input Voltage (logic high) | VENH | 2 | V | VEN = logic high (regulator enabled) | 5 | ||
| Error Flag Threshold | VERR | -2 | -6 | -10 | % | Undervoltage condition (below nominal); Note 8 | 5 |
| Output Logic-Low Voltage | VIL | 0.2 | 0.4 | V | IL = 1mA, undervoltage condition | 5 | |
| Flag Leakage Current | IFL | -1 | 0.1 | 1 | µA | Flag off, VFLAG = 0V to 12V | 5 |
| Supply Input Voltage (absolute maximum) | VIN | -20 | 20 | V | 4 | ||
| Junction Temperature (absolute maximum) | TJ | -40 | 125 | °C | 4 | ||
| Lead Temperature (soldering) | 260 | °C | Soldering, 5 sec | 4 | |||
| Supply Input Voltage (operating) | VIN | 2.5 | 12 | V | 4 | ||
| Enable Input Voltage (operating) | VEN | 0 | V | Upper limit VIN | 4 | ||
| Junction Temperature (operating) | TJ | -40 | 125 | °C | 4 | ||
| Thermal Resistance, junction-to-ambient | θJA | 160 | °C/W | MM8 (MM) package, recommended minimum footprint | 8 | ||
| Thermal Resistance, junction-to-ambient | θJA | 70 | °C/W | MM8 (MM) package, 1 in² copper clad | 8 | ||
| Thermal Resistance, junction-to-case | θJC | 30 | °C/W | MM8 (MM) package | 8 |
CAD (KiCad official)
- Symbol:
MIC5216-3.3YMM - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
mic5216-3-3ymm-etched.step/mic5216-3-3ymm-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic5216-3-3ymm.step/mic5216-3-3ymm.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet, copy hosted by LCSC (13 pp, sha256
3f9486ced6f887d9, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).