main
Ray Publish 0.1.0 54dd856

MIC47050-1.8YML-TR

Microchip Tech · Linear Voltage Regulators (LDO) · DFN-6-EP(2x2)

MIC47050-1.8YML-TR from Microchip Tech, in a DFN-6-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BIAS power_in Bias supply is the power input for the internal control circuitry of the regulator and should be bypassed with 0.1 µF ceramic capacitors to ground.
2 GND power_in Ground pin, which must be connected externally together with the exposed pad.
3 IN power_in Input supply and drain of the NMOS pass transistor, with a minimum input voltage of 1.0 V.
4 OUT power_out Regulated output voltage of the regulator, which requires a 1 µF or greater ceramic output capacitor for stability.
5 PGOOD output Open-drain power good output that is driven low when the output is below the power good threshold and goes high impedance when the output is above it.
6 EN input TTL/CMOS compatible enable input where logic-high enables the regulator and logic-low shuts it down, and it must not be left floating.
7 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package DFN-6-EP(2x2)
Category Power Supply Chip
Pins 7

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage Range VIN 1 3.6 V 4
VIN UVLO Threshold VIN_UVLO 0.7 0.85 1 V VIN Rising 4
Ground Current in Shutdown IGND 0.1 1 µA VEN ≤ 0.2V (Regulator Shutdown) 4
IN Bias Current IIN 6 15 µA IOUT = 500 mA; VIN = VOUT + 0.5V 4
BIAS Input Voltage VBIAS 2.3 5.5 V 4
VBIAS UVLO Threshold BIAS_UVLO 1.7 2.1 2.3 V VBIAS Rising 4
Dropout Voltage VBIAS - VOUT 1.25 2.1 V IOUT = 500 mA 5
VBIAS Supply Current IBIAS 330 500 µA IOUT = 1 mA; VBIAS = VOUT + 2.1V 5
VBIAS Supply Current in Shutdown IBIAS_SHDN 0.1 1 µA VEN ≤ 0.2V (Regulator Shutdown) 5
Dropout Voltage VIN - VOUT 9 50 mV IOUT = 100 mA 5
Dropout Voltage VIN - VOUT 44 120 mV IOUT = 500 mA 5
Output Voltage Accuracy VOUT -1.5 1.5 % IOUT = 100 µA, variation from nominal VOUT 5
Output Voltage Accuracy VOUT -2 2 % variation from nominal VOUT 5
VBIAS Line Regulation ΔVOUT/(VOUT x ΔVBIAS) -0.1 0.015 0.1 %/V VBIAS = VOUT + 2.1V to 5.5V 5
VIN Line Regulation ΔVOUT/(VOUT x ΔVIN) -0.05 0.005 0.05 %/V VIN = VOUT + 0.5V to 3.6V 5
Load Regulation ΔVOUT/VOUT 0.2 0.5 % IOUT = 10 mA to 500 mA 5
Short-Circuit Current Limit ISC 0.6 1.6 3 A VIN = 2.7V; VOUT = 0V 5
EN Logic Level High VEN_HIGH 1 0.77 V 5
EN Logic Level Low VEN_LOW 0.67 0.2 V 5
Enable Bias Current IEN_SHDN 1 2 µA VEN ≤ 0.2V (Regulator Shutdown) 5
Enable Bias Current IEN 6 10 µA VEN = 1.0V (Regulator Enabled) 5
Turn-On Time tON 15 500 µs COUT = 1 µF; 90% of typical VOUT 5
Power Good Threshold Voltage VPWRGD_TH_R 91 95 % VOUT Rising 5
Power Good Threshold Voltage VPWRGD_TH_F 85 89 % VOUT Falling 5
Power Good Output Low Voltage VPWRGD_L 0.02 0.1 V IPG = 250 µA 5
Power Good Leakage Current IPWRGD_L -1 0.01 1 µA VPG = 5.0V 5
Storage Temperature Range TS -65 150 °C 6
Junction Temperature Range TJ -40 125 °C 6
Lead Temperature 260 °C Soldering, 10 sec. 6
IN Supply Voltage (absolute maximum) VIN -0.3 4 V 4
Bias Supply Voltage (absolute maximum) VBIAS -0.3 6 V 4
Enable Voltage (absolute maximum) VEN -0.3 6 V 4
Power Good Voltage (absolute maximum) VPGOOD -0.3 6 V 4
ADJ Pin Voltage (absolute maximum) VADJ -0.3 6 V 4
OUT Pin Voltage (absolute maximum) VOUT -0.3 V maximum is VIN 4
ESD Rating 2 kV Note 2: Human body model, 1.5 kΩ in series with 100 pF 4
IN Supply Voltage (operating) VIN 1 3.6 V VIN < VBIAS 4
Bias Voltage (operating) VBIAS 2.3 5.5 V 4
Enable Input Voltage (operating) VEN 0 V up to VBIAS 4
Power Good Voltage (operating) VPGOOD 0 V up to VBIAS 4
Output Voltage Range 0.4 2 V 4
Thermal Resistance DFN-6 junction-to-ambient JA 90 °C/W 6
Thermal Resistance DFN-6 junction-to-case JC 45 °C/W 6

CAD (KiCad official)

  • Symbol: MIC47050-1.8YML-TR
  • Footprint: Package_DFN_QFN:DFN-6-1EP_2x2mm_P0.65mm_EP1x1.6mm
  • 3D model: DFN-6-EP(2x2) (KiCad packages3D, STEP)
  • 3D model files: mic47050-1-8yml-tr-etched.step / mic47050-1-8yml-tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mic47050-1-8yml-tr.step / mic47050-1-8yml-tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (24 pp, sha256 6a684ddf3f35ca2d, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF