3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMIC3203YM
Microchip Tech · LED Drivers · SOIC-8
MIC3203YM from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC | power_out | Voltage regulator output that supplies the internal circuitry, bypassed with a 1 μF ceramic capacitor placed as close as possible to VCC and AGND, and not to be connected to an external load. |
| 2 | CS | input | High-side current-sense input that sets the LED current with an external sense resistor. |
| 3 | VIN | power_in | Input supply pin for the internal circuitry and positive input to the current-sense comparator, bypassed with a 10 μF ceramic capacitor placed as close as possible to VIN and PGND. |
| 4 | AGND | power_in | Ground pin for analog circuitry, serving as the internal signal ground for all low-power sections. |
| 5 | EN | input | Logic-level enable input that must be at least 2.2V to enable the current regulator, must not be driven above the supply voltage, and reduces supply current below 1 μA when pulled low. |
| 6 | DIM | input | PWM dimming input that must be at least 2.0V to enable the output, and a low level disables the output regardless of the EN state. |
| 7 | PGND | power_in | Power ground for the high-current switching of the power FET, which should be kept as small as possible and separate from the AGND loop. |
| 8 | DRV | output | Gate-drive output that connects to the gate of an external N-channel MOSFET whose drain connects to the inductor, with its high-frequency, high-voltage switch node routed away from sensitive nodes. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-8 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Range | VIN | 4.5 | 42 | V | 3 | ||
| Supply Current | IS | 1 | 3 | mA | DRV = open | 3 | |
| Shutdown Current | ISD | 1 | μA | VEN = 0V | 3 | ||
| VIN UVLO Threshold | UVLO | 3.2 | 4 | 4.5 | V | VIN rising | 3 |
| VCC Output Voltage | VCC | 4.5 | 5 | 5.5 | V | VIN = 12V, ICC = 10 mA | 3 |
| Current Sense Voltage Upper Threshold | VCS(MAX) | 201.4 | 212 | 222.6 | mV | 3 | |
| Current Sense Voltage Upper Threshold | VCS(MAX) | 199 | 212 | 225 | mV | VCS(MAX) = VIN, VCS | 3 |
| Current Sense Voltage Lower Threshold | VCS(MIN) | 168 | 177 | 186 | mV | 3 | |
| Current Sense Voltage Lower Threshold | VCS(MIN) | 165 | 177 | 189 | mV | VCS(MIN) = VIN, VCS | 3 |
| CS Input Current | IIN(CS) | 0.5 | 10 | μA | VIN, VCS = 220 mV | 4 | |
| Switching Frequency | fSW | 1.5 | MHz | 4 | |||
| VCS Hysteresis Dithering Range | VDITH | -6 | 6 | mV | 4 | ||
| Frequency Dithering Range | fDITHER | -12 | 12 | % | Percent of Switching Frequency | 4 | |
| EN Logic Level High | VENH | 2.2 | V | 4 | |||
| EN Logic Level Low | VENL | 0.4 | V | 4 | |||
| EN Bias Current | IEN | 60 | μA | VEN = 12V | 4 | ||
| EN Bias Current | IEN | 1 | μA | VEN = 0V | 4 | ||
| DIM Logic Level High | VDIMH | 2 | V | 4 | |||
| DIM Logic Level Low | VDIML | 0.4 | V | 4 | |||
| DIM Bias Current | IDIM | 20 | 50 | μA | 4 | ||
| DIM Bias Current | IDIM | 1 | μA | VDIM = 0V | 4 | ||
| Maximum Dimming Frequency | fDIM | 20 | kHz | 4 | |||
| VIN to PGND | VIN | -0.3 | 45 | V | 3 | ||
| VCC to PGND | VCC | -0.3 | 6 | V | 3 | ||
| CS to PGND | VCS | -0.3 | V | maximum (VIN + 0.3V) | 3 | ||
| EN to AGND | VEN | -0.3 | V | maximum (VIN + 0.3V) | 3 | ||
| DIM to AGND | VDIM | -0.3 | V | maximum (VIN + 0.3V) | 3 | ||
| DRV to PGND | VDRV | -0.3 | V | maximum (VCC + 0.3V) | 3 | ||
| PGND to AGND | -0.3 | 0.3 | V | 3 | |||
| ESD Rating HBM | 1.5 | kV | Human body model, 1.5 kΩ in series with 100 pF | 3 | |||
| Supply Voltage | VIN | 4.5 | 42 | V | Operating Ratings | 3 | |
| Enable Input Voltage | VEN | 0 | V | up to VIN | 3 | ||
| Dimming Input Voltage | VDIM | 0 | V | up to VIN | 3 | ||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | Note 1 | 5 | |
| Maximum Junction Temperature | TJ(MAX) | 150 | °C | 5 | |||
| Storage Temperature Range | TS | -60 | 150 | °C | 5 | ||
| Lead Temperature | TLEAD | 260 | °C | Soldering, 10 sec. | 5 | ||
| Thermal Resistance, SOIC 8-Ld junction to air | θJA | 98.9 | °C/W | 5 | |||
| Thermal Resistance, SOIC 8-Ld junction to case | θJC | 48.8 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
MIC3203YM - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
mic3203ym-etched.step/mic3203ym-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic3203ym.step/mic3203ym.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet, copy hosted by LCSC (28 pp, sha256
f0cc0338148ed5a7, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).