Generated by kicad-footprint-generator · KiCad file format 20260206
MIC29503WU-TR
Microchip Tech · Power Management Specialized - PMIC · TO-263-5
MIC29503WU-TR from Microchip Tech, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FLAG | output | Active-low error flag output that indicates an output fault condition; it is an open-collector output that may sink 10 mA. |
| 2 | INPUT | power_in | Supplies the current to the output power device; the overvoltage sensor disables the regulator when the input voltage exceeds approximately 32V. |
| 3 | GND | power_in | Ground pin; the TAB is also connected internally to the IC ground. |
| 4 | OUTPUT | power_out | The regulator output voltage. |
| 5 | ADJUST | input | Adjustable regulator feedback input that connects to the resistor divider from OUTPUT to GND to set the output voltage, which can be programmed between 1.25V and 25V. |
| 6 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TO-263-5 |
| Category | Power Supply Chip |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage | VOUT | -1 | 1 | % | IOUT = 10 mA | 5 | |
| Output Voltage | VOUT | -2 | 2 | % | 10 mA ≤ IOUT ≤ IFL, (VOUT + 1V) ≤ VIN ≤26V (Note 3) | 5 | |
| Line Regulation | 0.06 | 0.5 | % | IOUT = 10 mA, (VOUT + 1V) ≤ VIN ≤ 26V | 5 | ||
| Load Regulation | 0.2 | 1 | % | VIN = VOUT + 1V, 10 mA ≤ IOUT ≤ 1.5A (Note 3, Note 4) | 5 | ||
| Output Voltage Temperature Coefficient | ΔVO/ΔT | 20 | 100 | ppm/°C | Output Voltage (Note 4) | 5 | |
| Dropout Voltage | 125 | 250 | mV | MIC2950x IOUT = 250 mA | 5 | ||
| Dropout Voltage | 370 | 600 | mV | MIC2950x IOUT = 5A | 5 | ||
| Ground Current | IGND | 15 | 50 | mA | MIC2950x IOUT = 2.5A, VIN = VOUT + 1V | 5 | |
| Current Limit | ILIM | 7.5 | 10 | A | MIC2950x, VOUT = 0V, (Note 7) | 5 | |
| Reference Voltage | 1.228 | 1.24 | 1.252 | V | 6 | ||
| Reference Voltage | 1.215 | 1.265 | V | Bold values: -40°C ≤ TJ ≤ +125°C | 6 | ||
| Reference Voltage | 1.203 | 1.277 | V | Note 8 | 6 | ||
| Adjust Pin Bias Current | 40 | 80 | nA | 6 | |||
| Adjust Pin Bias Current | 120 | nA | Bold values: -40°C ≤ TJ ≤ +125°C | 6 | |||
| Output Leakage Current (Flag) | 0.01 | 1 | µA | VOH = 26V | 6 | ||
| Output Leakage Current (Flag) | 2 | µA | VOH = 26V; bold values: -40°C ≤ TJ ≤ +125°C | 6 | |||
| Output Low Voltage | VOL | 220 | 300 | mV | Device set for 5V, VIN = 4.5V | 6 | |
| Output Low Voltage | VOL | 400 | mV | IOL = 250 µA; bold values: -40°C ≤ TJ ≤ +125°C | 6 | ||
| Upper Threshold Voltage | 40 | 60 | mV | Device set for 5V, (Note 10) | 6 | ||
| Upper Threshold Voltage | 25 | mV | Device set for 5V, (Note 10); bold values: -40°C ≤ TJ ≤ +125°C | 6 | |||
| Lower Threshold Voltage | 75 | 95 | mV | Device set for 5V, (Note 10) | 6 | ||
| Lower Threshold Voltage | 140 | mV | Device set for 5V, (Note 10); bold values: -40°C ≤ TJ ≤ +125°C | 6 | |||
| Input Supply Voltage | VIN | -20 | 60 | V | Note 1 | 4 | |
| Enable Input Voltage | VEN | -0.3 | V | Upper limit printed as VIN | 4 | ||
| Maximum Operating Input Voltage | 26 | V | 4 | ||||
| Storage Temperature Range | TS | -65 | 150 | °C | 8 | ||
| Operating Junction Temperature | TJ | -40 | 125 | °C | 8 | ||
| Lead Temperature | 260 | °C | Soldering, 5 sec. | 8 | |||
| Dropout Voltage | 250 | mV | MIC2950x IOUT = 2.5A | 5 | |||
| Ground Current | IGND | 70 | mA | MIC2950x IOUT = 5A | 5 | ||
| Ground Pin Current at Dropout | IGRNDDO | 2.1 | mA | MIC2950x, VIN = 0.5V less than specified VOUT × IOUT = 10 mA | 5 | ||
| Thermal Resistance TO-263 (junction to case) | θJC | 2 | °C/W | 8 |
CAD (KiCad official)
- Symbol:
MIC29503WU-TR - Footprint:
Package_TO_SOT_SMD:TO-263-5_TabPin6 - 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files:
mic29503wu-tr-etched.step/mic29503wu-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic29503wu-tr.step/mic29503wu-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (42 pp, sha256
e4243475719303fc, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).