Generated by kicad-footprint-generator · KiCad file format 20260206
MIC29501-5.0WU
Microchip Tech · Linear Voltage Regulators (LDO) · TO-263-5
MIC29501-5.0WU from Microchip Tech, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | CMOS compatible control input; logic-high enables the regulator and logic-low shuts it down. |
| 2 | IN | power_in | Supplies the current to the output power device. |
| 3 | GND | power_in | Ground pin; the TAB is also connected internally to the IC's ground on D-PAK. |
| 4 | OUT | power_out | The regulator output voltage. |
| 5 | FLG | output | Active-low error flag output that indicates an output fault condition (open-collector, may sink 10 mA per Section 4.5). |
| 6 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TO-263-5 |
| Category | Power Supply Chip |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage (5.0 V fixed, ±1%) | VOUT | -1 | 1 | % | IOUT = 10 mA | 5 | |
| Output Voltage (5.0 V fixed, ±2% over load and line) | VOUT | -2 | 2 | % | 10 mA ≤ IOUT ≤ IFL, (VOUT + 1V) ≤ VIN ≤26V (Note 3) | 5 | |
| Line Regulation | 0.06 | 0.5 | % | IOUT = 10 mA, (VOUT + 1V) ≤ VIN ≤ 26V | 5 | ||
| Load Regulation | 0.2 | 1 | % | VIN = VOUT + 1V, 10 mA ≤ IOUT ≤ 1.5A (Note 3, Note 4) | 5 | ||
| Output Voltage Temperature Coefficient | ∆VO/∆T | 20 | 100 | ppm/°C | Output Voltage (Note 4) | 5 | |
| Dropout Voltage, MIC2950x at 250 mA | 125 | 250 | mV | ΔVOUT = -1% (Note 5); MIC2950x IOUT = 250 mA | 5 | ||
| Dropout Voltage, MIC2950x at 5A | 370 | 600 | mV | ΔVOUT = -1% (Note 5); MIC2950x IOUT = 5A | 5 | ||
| Ground Current, MIC2950x at 2.5A | IGND | 15 | 50 | mA | MIC2950x IOUT = 2.5A, VIN = VOUT + 1V (Note 6) | 5 | |
| Current Limit, MIC2950x | ILIM | 7.5 | 10 | A | MIC2950x, VOUT = 0V, (Note 7) | 5 | |
| Flag Output Leakage Current | 0.01 | 1 | µA | VOH = 26V | 6 | ||
| Flag Output Leakage Current (bold, -40°C ≤ TJ ≤ +125°C) | 2 | µA | VOH = 26V; bold values indicate -40°C ≤ TJ ≤ +125°C | 6 | |||
| Flag Output Low Voltage | VOL | 220 | 300 | mV | Device set for 5V, VIN = 4.5V, IOL = 250 µA | 6 | |
| Flag Output Low Voltage (bold, -40°C ≤ TJ ≤ +125°C) | VOL | 400 | mV | Device set for 5V, VIN = 4.5V, IOL = 250 µA; bold values indicate -40°C ≤ TJ ≤ +125°C | 6 | ||
| Flag Upper Threshold Voltage | 40 | 60 | mV | Device set for 5V, (Note 10) | 6 | ||
| Flag Upper Threshold Voltage (bold, -40°C ≤ TJ ≤ +125°C) | 25 | mV | Device set for 5V, (Note 10); bold values indicate -40°C ≤ TJ ≤ +125°C | 6 | |||
| Flag Lower Threshold Voltage | 75 | 95 | mV | Device set for 5V, (Note 10) | 6 | ||
| Flag Lower Threshold Voltage (bold, -40°C ≤ TJ ≤ +125°C) | 140 | mV | Device set for 5V, (Note 10); bold values indicate -40°C ≤ TJ ≤ +125°C | 6 | |||
| Enable Input Logic Voltage Low (OFF) | 0.8 | V | , | 7 | |||
| Enable Input Logic Voltage High (ON) | 2.4 | V | , | 7 | |||
| Enable Pin Input Current | 100 | 600 | µA | VEN = 26V | 7 | ||
| Enable Pin Input Current (bold, -40°C ≤ TJ ≤ +125°C) | 750 | µA | VEN = 26V; bold values indicate -40°C ≤ TJ ≤ +125°C | 7 | |||
| Enable Pin Input Current at low enable level | 0.7 | 2 | µA | VEN = 0.8V | 7 | ||
| Enable Pin Input Current at low enable level (bold, -40°C ≤ TJ ≤ +125°C) | 4 | µA | VEN = 0.8V; bold values indicate -40°C ≤ TJ ≤ +125°C | 7 | |||
| Regulator Output Current in Shutdown | 10 | 500 | µA | VEN ≤ 0.8V and VIN ≤ 26V, VOUT = 0 | 7 | ||
| Input Supply Voltage (absolute maximum) | VIN | -20 | 60 | V | Note 1: maximum 60V of limited duration (<100 ms) and duty cycle (≤1%); maximum continuous supply 26V | 4 | |
| Enable Input Voltage (absolute maximum) | VEN | -0.3 | V | Maximum printed as VIN (-0.3V to VIN) | 4 | ||
| Maximum Operating Input Voltage | 26 | V | Operating Ratings | 4 | |||
| Storage Temperature Range | TS | -65 | 150 | °C | , | 8 | |
| Operating Junction Temperature | TJ | -40 | 125 | °C | , | 8 | |
| Lead Temperature | 260 | °C | Soldering, 5 sec. | 8 | |||
| Thermal Resistance Junction-to-Case, TO-263 | θJC | 2 | °C/W | , | 8 |
CAD (KiCad official)
- Symbol:
MIC29501-5.0WU - Footprint:
Package_TO_SOT_SMD:TO-263-5_TabPin6 - 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files:
mic29501-5-0wu-etched.step/mic29501-5-0wu-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic29501-5-0wu.step/mic29501-5-0wu.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (42 pp, sha256
e4243475719303fc, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).