Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MIC29501-5.0WU

Microchip Tech · Linear Voltage Regulators (LDO) · TO-263-5

MIC29501-5.0WU from Microchip Tech, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 EN input CMOS compatible control input; logic-high enables the regulator and logic-low shuts it down.
2 IN power_in Supplies the current to the output power device.
3 GND power_in Ground pin; the TAB is also connected internally to the IC's ground on D-PAK.
4 OUT power_out The regulator output voltage.
5 FLG output Active-low error flag output that indicates an output fault condition (open-collector, may sink 10 mA per Section 4.5).
6 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package TO-263-5
Category Power Supply Chip
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Output Voltage (5.0 V fixed, ±1%) VOUT -1 1 % IOUT = 10 mA 5
Output Voltage (5.0 V fixed, ±2% over load and line) VOUT -2 2 % 10 mA ≤ IOUT ≤ IFL, (VOUT + 1V) ≤ VIN ≤26V (Note 3) 5
Line Regulation 0.06 0.5 % IOUT = 10 mA, (VOUT + 1V) ≤ VIN ≤ 26V 5
Load Regulation 0.2 1 % VIN = VOUT + 1V, 10 mA ≤ IOUT ≤ 1.5A (Note 3, Note 4) 5
Output Voltage Temperature Coefficient ∆VO/∆T 20 100 ppm/°C Output Voltage (Note 4) 5
Dropout Voltage, MIC2950x at 250 mA 125 250 mV ΔVOUT = -1% (Note 5); MIC2950x IOUT = 250 mA 5
Dropout Voltage, MIC2950x at 5A 370 600 mV ΔVOUT = -1% (Note 5); MIC2950x IOUT = 5A 5
Ground Current, MIC2950x at 2.5A IGND 15 50 mA MIC2950x IOUT = 2.5A, VIN = VOUT + 1V (Note 6) 5
Current Limit, MIC2950x ILIM 7.5 10 A MIC2950x, VOUT = 0V, (Note 7) 5
Flag Output Leakage Current 0.01 1 µA VOH = 26V 6
Flag Output Leakage Current (bold, -40°C ≤ TJ ≤ +125°C) 2 µA VOH = 26V; bold values indicate -40°C ≤ TJ ≤ +125°C 6
Flag Output Low Voltage VOL 220 300 mV Device set for 5V, VIN = 4.5V, IOL = 250 µA 6
Flag Output Low Voltage (bold, -40°C ≤ TJ ≤ +125°C) VOL 400 mV Device set for 5V, VIN = 4.5V, IOL = 250 µA; bold values indicate -40°C ≤ TJ ≤ +125°C 6
Flag Upper Threshold Voltage 40 60 mV Device set for 5V, (Note 10) 6
Flag Upper Threshold Voltage (bold, -40°C ≤ TJ ≤ +125°C) 25 mV Device set for 5V, (Note 10); bold values indicate -40°C ≤ TJ ≤ +125°C 6
Flag Lower Threshold Voltage 75 95 mV Device set for 5V, (Note 10) 6
Flag Lower Threshold Voltage (bold, -40°C ≤ TJ ≤ +125°C) 140 mV Device set for 5V, (Note 10); bold values indicate -40°C ≤ TJ ≤ +125°C 6
Enable Input Logic Voltage Low (OFF) 0.8 V , 7
Enable Input Logic Voltage High (ON) 2.4 V , 7
Enable Pin Input Current 100 600 µA VEN = 26V 7
Enable Pin Input Current (bold, -40°C ≤ TJ ≤ +125°C) 750 µA VEN = 26V; bold values indicate -40°C ≤ TJ ≤ +125°C 7
Enable Pin Input Current at low enable level 0.7 2 µA VEN = 0.8V 7
Enable Pin Input Current at low enable level (bold, -40°C ≤ TJ ≤ +125°C) 4 µA VEN = 0.8V; bold values indicate -40°C ≤ TJ ≤ +125°C 7
Regulator Output Current in Shutdown 10 500 µA VEN ≤ 0.8V and VIN ≤ 26V, VOUT = 0 7
Input Supply Voltage (absolute maximum) VIN -20 60 V Note 1: maximum 60V of limited duration (<100 ms) and duty cycle (≤1%); maximum continuous supply 26V 4
Enable Input Voltage (absolute maximum) VEN -0.3 V Maximum printed as VIN (-0.3V to VIN) 4
Maximum Operating Input Voltage 26 V Operating Ratings 4
Storage Temperature Range TS -65 150 °C , 8
Operating Junction Temperature TJ -40 125 °C , 8
Lead Temperature 260 °C Soldering, 5 sec. 8
Thermal Resistance Junction-to-Case, TO-263 θJC 2 °C/W , 8

CAD (KiCad official)

  • Symbol: MIC29501-5.0WU
  • Footprint: Package_TO_SOT_SMD:TO-263-5_TabPin6
  • 3D model: TO-263-5 (KiCad packages3D, STEP)
  • 3D model files: mic29501-5-0wu-etched.step / mic29501-5-0wu-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mic29501-5-0wu.step / mic29501-5-0wu.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (42 pp, sha256 e4243475719303fc, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF