main
Ray Publish 0.1.0 24ce2b4

MIC26603YJL-TR

Microchip Tech · DC-DC Converters · QFN-28(5x6)

MIC26603YJL-TR from Microchip Tech, in a QFN-28(5x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 PVDD power_out 5V internal LDO output from VIN that supplies the power MOSFET gate drive, tied to PVIN when VIN < 5.5V, with a 2.2µF ceramic capacitor to PGND (pin 2) placed next to the IC.
2 PGND power_in Power ground for the buck converter power stage, connecting to the low-side MOSFET gate drive return, MOSFET sources and input/output capacitor negative terminals, with the loop kept small and separate from the SGND loop.
3 NC unconnected No connect.
4 SW power_out Switch node connecting the high-side MOSFET source and low-side MOSFET drain, to be routed away from sensitive nodes due to high-speed switching.
5 PGND power_in Power ground for the buck converter power stage, connecting to the low-side MOSFET gate drive return, MOSFET sources and input/output capacitor negative terminals, with the loop kept small and separate from the SGND loop.
6 PGND power_in Power ground for the buck converter power stage, connecting to the low-side MOSFET gate drive return, MOSFET sources and input/output capacitor negative terminals, with the loop kept small and separate from the SGND loop.
7 PGND power_in Power ground for the buck converter power stage, connecting to the low-side MOSFET gate drive return, MOSFET sources and input/output capacitor negative terminals, with the loop kept small and separate from the SGND loop.
8 PGND power_in Power ground for the buck converter power stage, connecting to the low-side MOSFET gate drive return, MOSFET sources and input/output capacitor negative terminals, with the loop kept small and separate from the SGND loop.
9 SW power_out Switch node connecting the high-side MOSFET source and low-side MOSFET drain, to be routed away from sensitive nodes due to high-speed switching.
10 SW power_out Switch node connecting the high-side MOSFET source and low-side MOSFET drain, to be routed away from sensitive nodes due to high-speed switching.
11 SW power_out Switch node connecting the high-side MOSFET source and low-side MOSFET drain, to be routed away from sensitive nodes due to high-speed switching.
12 SW power_out Switch node connecting the high-side MOSFET source and low-side MOSFET drain, to be routed away from sensitive nodes due to high-speed switching.
13 PVIN power_in High-side N-MOSFET drain input with 4.5V to 26V operating range, requiring input capacitors to PGND with short connections.
14 PVIN power_in High-side N-MOSFET drain input with 4.5V to 26V operating range, requiring input capacitors to PGND with short connections.
15 PVIN power_in High-side N-MOSFET drain input with 4.5V to 26V operating range, requiring input capacitors to PGND with short connections.
16 PVIN power_in High-side N-MOSFET drain input with 4.5V to 26V operating range, requiring input capacitors to PGND with short connections.
17 PVIN power_in High-side N-MOSFET drain input with 4.5V to 26V operating range, requiring input capacitors to PGND with short connections.
18 PVIN power_in High-side N-MOSFET drain input with 4.5V to 26V operating range, requiring input capacitors to PGND with short connections.
19 PVIN power_in High-side N-MOSFET drain input with 4.5V to 26V operating range, requiring input capacitors to PGND with short connections.
20 BST passive Bootstrapped supply for the high-side N-channel MOSFET driver, with a Schottky diode to PVDD, a 0.1µF capacitor to SW, and an optional small series resistor to slow high-side turn-on.
21 PGND power_in Power ground for the buck converter power stage, connecting to the low-side MOSFET gate drive return, MOSFET sources and input/output capacitor negative terminals, with the loop kept small and separate from the SGND loop.
22 CS input Current sense input monitoring the low-side MOSFET voltage during OFF-time for short-circuit protection and zero-current detection, connected to the low-side MOSFET drain via Kelvin connection to SW, and also the high-side MOSFET driver return.
23 SGND power_in Signal ground that must be connected directly to the ground planes and not routed to the PGND pad on the top layer.
24 FB input Feedback input to the transconductance amplifier, regulated to 0.8V, with a resistor divider from the output setting the output voltage.
25 PG output Open-drain power good output pulled up externally with a resistor to VDD, asserted high when VOUT is above 92% of nominal.
26 EN input CMOS-compatible enable input where logic high enables and logic low shuts down (typically 5µA supply current), and it must not be left open.
27 VIN power_in Power supply input (4.5V to 28V operating) requiring a bypass capacitor to SGND.
28 VDD power_out 5V internal LDO output from VIN supplying the IC control circuit, tied to PVIN pins when VIN < 5.5V, with a 1.0µF ceramic capacitor to SGND placed next to the IC.
29 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package QFN-28(5x6)
Category Power Management
Pins 29

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage Range (VIN, PVIN) VIN 4.5 28 V 4
Quiescent Supply Current IQ 450 750 µA VFB = 1.5V (non-switching) 4
Shutdown Supply Current 5 10 µA VEN = 0V 4
VDD Output Voltage VDD 4.8 5 5.4 V VIN = 7V to 28V, IDD = 40mA 4
VDD UVLO Threshold 3.7 4.2 4.5 V VDD Rising 4
Dropout Voltage (VIN, VDD) 380 600 mV IDD = 25mA 4
Output-Voltage Adjust Range VOUT 0.8 5.5 V 4
Reference (±1.0%) VREF 0.792 0.8 0.808 V 0°C ≤ TJ ≤ 85°C 4
Reference (±1.5%) VREF 0.788 0.8 0.812 V −40°C ≤ TJ ≤ 125°C 4
FB Bias Current 50 500 nA VFB = 0.8V 4
EN Logic Level High 1.8 V 4
EN Logic Level Low 0.6 V 4
EN Bias Current 6 30 µA VEN = 12V 4
Switching Frequency 450 600 750 kHz Measured in test mode 4
Current-Limit Threshold (25°C) 7.5 13 17 A VFB = 0.8V, TJ = 25°C 5
Current-Limit Threshold (125°C) 6.6 13 17 A VFB = 0.8V, TJ = 125°C 5
Power Good Threshold Voltage 85 92 95 %VOUT Sweep VFB from Low to High 5
Power Good Low Voltage 70 200 mV Sweep VFB < 0.9 × VNOM, IPG = 1mA 5
Load Regulation 0.25 % IOUT = 1A to 6A (Continuous Mode) 4
Line Regulation 0.25 % VIN = 4.5V to 28V 4
VDD UVLO Hysteresis 400 mV 4
Maximum Duty Cycle 82 % VFB = 0V 4
Minimum Duty Cycle 0 % VFB = 1.0V 4
Minimum Off-Time 300 ns 4
Soft-Start time 5 ms 5
Short-Circuit Current 2.7 A VFB = 0V 5
Top-MOSFET RDS(ON) RDS(ON) 42 mΩ ISW = 3A 5
Bottom-MOSFET RDS(ON) RDS(ON) 12.5 mΩ ISW = 3A 5
SW Leakage Current 60 µA VEN = 0V 5
VIN Leakage Current 25 µA VEN = 0V 5
Power Good Hysteresis 5.5 %VOUT Sweep VFB from High to Low 5
Power Good Delay Time 100 µs Sweep VFB from Low to High 5
Over-Temperature Shutdown 160 °C TJ Rising 5
Over-Temperature Shutdown Hysteresis 15 °C 5
PVIN to PGND -0.3 29 V 4
VIN to PGND -0.3 V upper limit PVIN 4
PVDD, VDD to PGND -0.3 6 V 4
VBST to VSW -0.3 6 V 4
VBST to PGND -0.3 35 V 4
PGND to SGND -0.3 0.3 V 4
Junction Temperature TJ 150 °C 4
Storage Temperature TS -65 150 °C 4
Lead Temperature 260 °C soldering, 10sec 4
Supply Voltage (PVIN, VIN) 4.5 28 V 4
PVDD, VDD Supply Voltage 4.5 5.5 V 4
Junction Temperature TJ -40 125 °C 4
Package Thermal Resistance θJA 28 °C/W 5 sq in 4-layer FR-4 PCB, 2oz copper 4

CAD (KiCad official)

  • Symbol: MIC26603YJL-TR
  • Footprint: Package_DFN_QFN:QFN-28-1EP_5x6mm_P0.5mm_EP3.65x4.65mm
  • 3D model: QFN-28(5x6) (KiCad packages3D, STEP)
  • 3D model files: mic26603yjl-tr-etched.step / mic26603yjl-tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mic26603yjl-tr.step / mic26603yjl-tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (30 pp, sha256 da013cde7364f29e, retrieved 2026-10-30, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF