main
Ray
Publish 0.1.0
4dbcb06
MIC22705YML-TR
Microchip Tech · DC-DC Converters · QFN-24-EP(4x4)
MIC22705YML-TR from Microchip Tech, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PVIN | power_in | Power supply input to the internal P-channel power MOSFET; a 22 μF ceramic is recommended for bypassing at each PVIN pin, and SVIN must be connected to a PVIN pin. |
| 6 | PVIN | power_in | Power supply input to the internal P-channel power MOSFET; a 22 μF ceramic is recommended for bypassing at each PVIN pin, and SVIN must be connected to a PVIN pin. |
| 13 | PVIN | power_in | Power supply input to the internal P-channel power MOSFET; a 22 μF ceramic is recommended for bypassing at each PVIN pin, and SVIN must be connected to a PVIN pin. |
| 18 | PVIN | power_in | Power supply input to the internal P-channel power MOSFET; a 22 μF ceramic is recommended for bypassing at each PVIN pin, and SVIN must be connected to a PVIN pin. |
| 2 | EN/DLY | input | Enable/delay input fed by a 1 μA source from SVIN; a capacitor sets turn-on delay and internal circuits stay off until the pin reaches the 1.24V enable threshold. |
| 3 | NC | unconnected | No connect; leave open and do not connect to ground or route other signals through this pin. |
| 4 | RC | passive | Ramp control; a capacitor to ground sets the output start-up slew rate from an internal 1 μA source, used for soft start and tracking. |
| 5 | PG | output | Open-drain power good output that indicates when the output voltage is below 90% of nominal and asserts without delay when enable is low or output falls below 90%. |
| 14 | FB | input | Feedback input to the error amplifier, regulated to 0.7V, with a resistor divider from the output setting the output voltage. |
| 15 | COMP | input | Compensation pin where a single external capacitor and resistor add the pole and zero for voltage mode loop stability with low-ESR ceramic capacitors. |
| 16 | SGND | power_in | Signal ground for all low power circuits, to be connected directly to the ground plane. |
| 17 | SVIN | power_in | Signal power supply input connected externally to PVIN, requiring a 2.2 μF ceramic capacitor to SGND placed next to the IC. |
| 7 | PGND | power_in | Power ground, the internal connection to the source of the internal N-channel MOSFETs. |
| 12 | PGND | power_in | Power ground, the internal connection to the source of the internal N-channel MOSFETs. |
| 19 | PGND | power_in | Power ground, the internal connection to the source of the internal N-channel MOSFETs. |
| 24 | PGND | power_in | Power ground, the internal connection to the source of the internal N-channel MOSFETs. |
| 8 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 9 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 10 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 11 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 20 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 21 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 22 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 23 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-24-EP(4x4) |
| Category | Power Management |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage Range | PVIN | 2.9 | 5.5 | V | 3 | ||
| UVLO Trip Level | 2.55 | 2.75 | 2.9 | V | PVIN rising | 3 | |
| Quiescent Supply Current | 0.85 | 1.3 | mA | VFB = 0.9V (not switching) | 3 | ||
| Shutdown Current | ISHDN | 5 | 10 | μA | VEN/DLY = 0V | 3 | |
| Feedback Voltage | VFB | 0.686 | 0.7 | 0.714 | V | 3 | |
| EN/DLY Threshold Voltage | 1.14 | 1.24 | 1.34 | V | 3 | ||
| EN/DLY Bias Current | 0.6 | 1 | 1.8 | μA | VEN/DLY = 0.5V; VIN = 2.9V and VIN = 5.5V | 3 | |
| RC Pin Source Current | IRAMP | 0.5 | 1 | 1.7 | μA | VRC = 0.35V | 3 |
| Switching Frequency | fSW | 0.8 | 1 | 1.2 | MHz | 4 | |
| Maximum Duty Cycle | 100 | % | VFB ≤ 0.5V | 4 | |||
| Current Limit | ILIM | 7 | 11 | 21 | A | VFB = 0.5V | 4 |
| SW Leakage Current | 60 | μA | PVIN = 5.5V, VSW = 5.5V, VEN = 0V | 4 | |||
| VIN Leakage Current | 25 | μA | PVIN = 5.5V, VSW = 0V, VEN = 0V | 4 | |||
| PG Threshold | -7.5 | -10 | -12.5 | % | Threshold % of VFB from VREF | 4 | |
| PG Leakage Current | 1 | 2 | μA | VPG = 5.5V; VFB = 0.9V | 4 | ||
| Junction Temperature Range | TJ | -40 | 125 | °C | 4 | ||
| Maximum Junction Temperature | TJ(MAX) | 150 | °C | 4 | |||
| Storage Temperature Range | TS | -65 | 150 | °C | 4 | ||
| PVIN to PGND | PVIN | -0.3 | 6 | V | 3 | ||
| SVIN to PGND | SVIN | -0.3 | V | upper limit PVIN | 3 | ||
| VSW to PGND | VSW | -0.3 | V | upper limit PVIN | 3 | ||
| VEN/DLY to PGND | VEN/DLY | -0.3 | V | upper limit PVIN | 3 | ||
| VPG to PGND | VPG | -0.3 | V | upper limit PVIN | 3 | ||
| PGND to SGND | -0.3 | 0.3 | V | 3 | |||
| Supply Voltage (operating) | 2.9 | 5.5 | V | 3 | |||
| Power Good Voltage | VPG | 0 | V | upper limit PVIN | 3 | ||
| Enable Input | VEN/DLY | 0 | V | upper limit PVIN | 3 | ||
| UVLO Hysteresis | 420 | mV | 3 | ||||
| FB Bias Current | 10 | nA | VFB = 0.5V | 3 | |||
| Load Regulation | 0.2 | % | IOUT = 100 mA to 7A | 3 | |||
| Line Regulation | 0.2 | % | VIN = 2.9V to 5.5V; IOUT = 100 mA | 3 | |||
| EN Hysteresis | 10 | mV | 3 | ||||
| Top MOSFET RDS(ON) | RDS(ON) | 30 | mΩ | VFB = 0.5V, ISW = 1A | 4 | ||
| Bottom MOSFET RDS(ON) | RDS(ON) | 25 | mΩ | VFB = 0.9V, ISW = -1A | 4 | ||
| PG Hysteresis | 2 | % | 4 | ||||
| PG Output Low Voltage | 144 | mV | IPG = 5 mA (sinking), VEN/DLY = 0V | 4 | |||
| Overtemperature Shutdown | 160 | °C | TJ rising | 4 | |||
| Overtemperature Shutdown Hysteresis | 20 | °C | 4 | ||||
| Lead Temperature | 260 | °C | Soldering, 10 sec. | 4 | |||
| Thermal Resistance, junction to case | θJC | 14 | °C/W | QFN 24-Ld | 4 | ||
| Thermal Resistance, junction to ambient | θJA | 40 | °C/W | QFN 24-Ld | 4 |
CAD (KiCad official)
- Symbol:
MIC22705YML-TR - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
mic22705yml-tr-etched.step/mic22705yml-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic22705yml-tr.step/mic22705yml-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (30 pp, sha256
5883f0a875c4f278, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MIC22705YML-TR
**Microchip Tech** · DC-DC Converters · QFN-24-EP(4x4)
MIC22705YML-TR from Microchip Tech, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PVIN | power_in | Power supply input to the internal P-channel power MOSFET; a 22 μF ceramic is recommended for bypassing at each PVIN pin, and SVIN must be connected to a PVIN pin. |
| 6 | PVIN | power_in | Power supply input to the internal P-channel power MOSFET; a 22 μF ceramic is recommended for bypassing at each PVIN pin, and SVIN must be connected to a PVIN pin. |
| 13 | PVIN | power_in | Power supply input to the internal P-channel power MOSFET; a 22 μF ceramic is recommended for bypassing at each PVIN pin, and SVIN must be connected to a PVIN pin. |
| 18 | PVIN | power_in | Power supply input to the internal P-channel power MOSFET; a 22 μF ceramic is recommended for bypassing at each PVIN pin, and SVIN must be connected to a PVIN pin. |
| 2 | EN/DLY | input | Enable/delay input fed by a 1 μA source from SVIN; a capacitor sets turn-on delay and internal circuits stay off until the pin reaches the 1.24V enable threshold. |
| 3 | NC | unconnected | No connect; leave open and do not connect to ground or route other signals through this pin. |
| 4 | RC | passive | Ramp control; a capacitor to ground sets the output start-up slew rate from an internal 1 μA source, used for soft start and tracking. |
| 5 | PG | output | Open-drain power good output that indicates when the output voltage is below 90% of nominal and asserts without delay when enable is low or output falls below 90%. |
| 14 | FB | input | Feedback input to the error amplifier, regulated to 0.7V, with a resistor divider from the output setting the output voltage. |
| 15 | COMP | input | Compensation pin where a single external capacitor and resistor add the pole and zero for voltage mode loop stability with low-ESR ceramic capacitors. |
| 16 | SGND | power_in | Signal ground for all low power circuits, to be connected directly to the ground plane. |
| 17 | SVIN | power_in | Signal power supply input connected externally to PVIN, requiring a 2.2 μF ceramic capacitor to SGND placed next to the IC. |
| 7 | PGND | power_in | Power ground, the internal connection to the source of the internal N-channel MOSFETs. |
| 12 | PGND | power_in | Power ground, the internal connection to the source of the internal N-channel MOSFETs. |
| 19 | PGND | power_in | Power ground, the internal connection to the source of the internal N-channel MOSFETs. |
| 24 | PGND | power_in | Power ground, the internal connection to the source of the internal N-channel MOSFETs. |
| 8 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 9 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 10 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 11 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 20 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 21 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 22 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 23 | SW | output | Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-24-EP(4x4) |
| Category | Power Management |
| Pins | 25 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage Range | PVIN | 2.9 | | 5.5 | V | | 3 |
| UVLO Trip Level | | 2.55 | 2.75 | 2.9 | V | PVIN rising | 3 |
| Quiescent Supply Current | | | 0.85 | 1.3 | mA | VFB = 0.9V (not switching) | 3 |
| Shutdown Current | ISHDN | | 5 | 10 | μA | VEN/DLY = 0V | 3 |
| Feedback Voltage | VFB | 0.686 | 0.7 | 0.714 | V | | 3 |
| EN/DLY Threshold Voltage | | 1.14 | 1.24 | 1.34 | V | | 3 |
| EN/DLY Bias Current | | 0.6 | 1 | 1.8 | μA | VEN/DLY = 0.5V; VIN = 2.9V and VIN = 5.5V | 3 |
| RC Pin Source Current | IRAMP | 0.5 | 1 | 1.7 | μA | VRC = 0.35V | 3 |
| Switching Frequency | fSW | 0.8 | 1 | 1.2 | MHz | | 4 |
| Maximum Duty Cycle | | 100 | | | % | VFB ≤ 0.5V | 4 |
| Current Limit | ILIM | 7 | 11 | 21 | A | VFB = 0.5V | 4 |
| SW Leakage Current | | | | 60 | μA | PVIN = 5.5V, VSW = 5.5V, VEN = 0V | 4 |
| VIN Leakage Current | | | | 25 | μA | PVIN = 5.5V, VSW = 0V, VEN = 0V | 4 |
| PG Threshold | | -7.5 | -10 | -12.5 | % | Threshold % of VFB from VREF | 4 |
| PG Leakage Current | | | 1 | 2 | μA | VPG = 5.5V; VFB = 0.9V | 4 |
| Junction Temperature Range | TJ | -40 | | 125 | °C | | 4 |
| Maximum Junction Temperature | TJ(MAX) | | | 150 | °C | | 4 |
| Storage Temperature Range | TS | -65 | | 150 | °C | | 4 |
| PVIN to PGND | PVIN | -0.3 | | 6 | V | | 3 |
| SVIN to PGND | SVIN | -0.3 | | | V | upper limit PVIN | 3 |
| VSW to PGND | VSW | -0.3 | | | V | upper limit PVIN | 3 |
| VEN/DLY to PGND | VEN/DLY | -0.3 | | | V | upper limit PVIN | 3 |
| VPG to PGND | VPG | -0.3 | | | V | upper limit PVIN | 3 |
| PGND to SGND | | -0.3 | | 0.3 | V | | 3 |
| Supply Voltage (operating) | | 2.9 | | 5.5 | V | | 3 |
| Power Good Voltage | VPG | 0 | | | V | upper limit PVIN | 3 |
| Enable Input | VEN/DLY | 0 | | | V | upper limit PVIN | 3 |
| UVLO Hysteresis | | | 420 | | mV | | 3 |
| FB Bias Current | | | 10 | | nA | VFB = 0.5V | 3 |
| Load Regulation | | | 0.2 | | % | IOUT = 100 mA to 7A | 3 |
| Line Regulation | | | 0.2 | | % | VIN = 2.9V to 5.5V; IOUT = 100 mA | 3 |
| EN Hysteresis | | | 10 | | mV | | 3 |
| Top MOSFET RDS(ON) | RDS(ON) | | 30 | | mΩ | VFB = 0.5V, ISW = 1A | 4 |
| Bottom MOSFET RDS(ON) | RDS(ON) | | 25 | | mΩ | VFB = 0.9V, ISW = -1A | 4 |
| PG Hysteresis | | | 2 | | % | | 4 |
| PG Output Low Voltage | | | 144 | | mV | IPG = 5 mA (sinking), VEN/DLY = 0V | 4 |
| Overtemperature Shutdown | | | 160 | | °C | TJ rising | 4 |
| Overtemperature Shutdown Hysteresis | | | 20 | | °C | | 4 |
| Lead Temperature | | | 260 | | °C | Soldering, 10 sec. | 4 |
| Thermal Resistance, junction to case | θJC | | 14 | | °C/W | QFN 24-Ld | 4 |
| Thermal Resistance, junction to ambient | θJA | | 40 | | °C/W | QFN 24-Ld | 4 |
## CAD (KiCad official)
- Symbol: `MIC22705YML-TR`
- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`
- 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files: `mic22705yml-tr-etched.step` / `mic22705yml-tr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mic22705yml-tr.step` / `mic22705yml-tr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/mic22705yml-tr-datasheet.pdf) (30 pp, sha256 `5883f0a875c4f278`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mic22705yml-tr-datasheet.pdf)