main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers mic22705yml-tr: viewers · Ray
mic22705yml-tr-etched.glb Publish 0.1.0 · Ray
mic22705yml-tr-etched.step mic22705yml-tr: factory component page (tier=mfr) · Ray
mic22705yml-tr-hero.glb mic22705yml-tr: hero GLB from the etched model (keeps the MPN mark) · Ray
mic22705yml-tr-hero.overlay.json Publish 0.1.0 · Ray
mic22705yml-tr.glb Publish 0.1.0 · Ray
mic22705yml-tr.kicad_mod Publish 0.1.0 · Ray
mic22705yml-tr.kicad_sym Publish 0.1.0 · Ray
mic22705yml-tr.lbr Publish 0.1.0 · Ray
mic22705yml-tr.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 25 pins · Ray

MIC22705YML-TR

Microchip Tech · DC-DC Converters · QFN-24-EP(4x4)

MIC22705YML-TR from Microchip Tech, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 PVIN power_in Power supply input to the internal P-channel power MOSFET; a 22 μF ceramic is recommended for bypassing at each PVIN pin, and SVIN must be connected to a PVIN pin.
6 PVIN power_in Power supply input to the internal P-channel power MOSFET; a 22 μF ceramic is recommended for bypassing at each PVIN pin, and SVIN must be connected to a PVIN pin.
13 PVIN power_in Power supply input to the internal P-channel power MOSFET; a 22 μF ceramic is recommended for bypassing at each PVIN pin, and SVIN must be connected to a PVIN pin.
18 PVIN power_in Power supply input to the internal P-channel power MOSFET; a 22 μF ceramic is recommended for bypassing at each PVIN pin, and SVIN must be connected to a PVIN pin.
2 EN/DLY input Enable/delay input fed by a 1 μA source from SVIN; a capacitor sets turn-on delay and internal circuits stay off until the pin reaches the 1.24V enable threshold.
3 NC unconnected No connect; leave open and do not connect to ground or route other signals through this pin.
4 RC passive Ramp control; a capacitor to ground sets the output start-up slew rate from an internal 1 μA source, used for soft start and tracking.
5 PG output Open-drain power good output that indicates when the output voltage is below 90% of nominal and asserts without delay when enable is low or output falls below 90%.
14 FB input Feedback input to the error amplifier, regulated to 0.7V, with a resistor divider from the output setting the output voltage.
15 COMP input Compensation pin where a single external capacitor and resistor add the pole and zero for voltage mode loop stability with low-ESR ceramic capacitors.
16 SGND power_in Signal ground for all low power circuits, to be connected directly to the ground plane.
17 SVIN power_in Signal power supply input connected externally to PVIN, requiring a 2.2 μF ceramic capacitor to SGND placed next to the IC.
7 PGND power_in Power ground, the internal connection to the source of the internal N-channel MOSFETs.
12 PGND power_in Power ground, the internal connection to the source of the internal N-channel MOSFETs.
19 PGND power_in Power ground, the internal connection to the source of the internal N-channel MOSFETs.
24 PGND power_in Power ground, the internal connection to the source of the internal N-channel MOSFETs.
8 SW output Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide.
9 SW output Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide.
10 SW output Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide.
11 SW output Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide.
20 SW output Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide.
21 SW output Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide.
22 SW output Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide.
23 SW output Switch node connected to the drains of the internal P-channel and N-channel MOSFETs; a high-frequency, high-power connection whose traces should be short and wide.
25 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package QFN-24-EP(4x4)
Category Power Management
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage Range PVIN 2.9 5.5 V 3
UVLO Trip Level 2.55 2.75 2.9 V PVIN rising 3
Quiescent Supply Current 0.85 1.3 mA VFB = 0.9V (not switching) 3
Shutdown Current ISHDN 5 10 μA VEN/DLY = 0V 3
Feedback Voltage VFB 0.686 0.7 0.714 V 3
EN/DLY Threshold Voltage 1.14 1.24 1.34 V 3
EN/DLY Bias Current 0.6 1 1.8 μA VEN/DLY = 0.5V; VIN = 2.9V and VIN = 5.5V 3
RC Pin Source Current IRAMP 0.5 1 1.7 μA VRC = 0.35V 3
Switching Frequency fSW 0.8 1 1.2 MHz 4
Maximum Duty Cycle 100 % VFB ≤ 0.5V 4
Current Limit ILIM 7 11 21 A VFB = 0.5V 4
SW Leakage Current 60 μA PVIN = 5.5V, VSW = 5.5V, VEN = 0V 4
VIN Leakage Current 25 μA PVIN = 5.5V, VSW = 0V, VEN = 0V 4
PG Threshold -7.5 -10 -12.5 % Threshold % of VFB from VREF 4
PG Leakage Current 1 2 μA VPG = 5.5V; VFB = 0.9V 4
Junction Temperature Range TJ -40 125 °C 4
Maximum Junction Temperature TJ(MAX) 150 °C 4
Storage Temperature Range TS -65 150 °C 4
PVIN to PGND PVIN -0.3 6 V 3
SVIN to PGND SVIN -0.3 V upper limit PVIN 3
VSW to PGND VSW -0.3 V upper limit PVIN 3
VEN/DLY to PGND VEN/DLY -0.3 V upper limit PVIN 3
VPG to PGND VPG -0.3 V upper limit PVIN 3
PGND to SGND -0.3 0.3 V 3
Supply Voltage (operating) 2.9 5.5 V 3
Power Good Voltage VPG 0 V upper limit PVIN 3
Enable Input VEN/DLY 0 V upper limit PVIN 3
UVLO Hysteresis 420 mV 3
FB Bias Current 10 nA VFB = 0.5V 3
Load Regulation 0.2 % IOUT = 100 mA to 7A 3
Line Regulation 0.2 % VIN = 2.9V to 5.5V; IOUT = 100 mA 3
EN Hysteresis 10 mV 3
Top MOSFET RDS(ON) RDS(ON) 30 mΩ VFB = 0.5V, ISW = 1A 4
Bottom MOSFET RDS(ON) RDS(ON) 25 mΩ VFB = 0.9V, ISW = -1A 4
PG Hysteresis 2 % 4
PG Output Low Voltage 144 mV IPG = 5 mA (sinking), VEN/DLY = 0V 4
Overtemperature Shutdown 160 °C TJ rising 4
Overtemperature Shutdown Hysteresis 20 °C 4
Lead Temperature 260 °C Soldering, 10 sec. 4
Thermal Resistance, junction to case θJC 14 °C/W QFN 24-Ld 4
Thermal Resistance, junction to ambient θJA 40 °C/W QFN 24-Ld 4

CAD (KiCad official)

  • Symbol: MIC22705YML-TR
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm
  • 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: mic22705yml-tr-etched.step / mic22705yml-tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mic22705yml-tr.step / mic22705yml-tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (30 pp, sha256 5883f0a875c4f278, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF