main
Ray Publish 0.1.0 02d08e9

MIC22400YML-TR

Microchip Tech · DC-DC Converters · QFN-20-EP(4x3)

MIC22400YML-TR from Microchip Tech, in a QFN-20-EP(4x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 POR output Power-On-Reset open-drain output indicating when the output is out of regulation, active after the delay set by the DELAY pin.
2 CF passive Adjustable frequency set with an external capacitor.
3 NC unconnected Not connected internally.
4 COMP input Compensation pin; place an RC to GND to compensate the device.
5 NC unconnected Not connected internally.
6 FB input Feedback input to the error amplifier, connected to the external resistor divider that sets the output voltage.
7 SGND power_in Signal ground.
8 SVIN power_in Signal power supply voltage input; requires a bypass capacitor to GND.
9 NC unconnected Not connected internally.
10 PVIN power_in Power supply voltage input; requires a bypass capacitor to GND.
11 PGND power_in Power ground.
12 SW power_out Switch output from the internal power MOSFET switches.
13 SW power_out Switch output from the internal power MOSFET switches.
14 SW power_out Switch output from the internal power MOSFET switches.
15 SW power_out Switch output from the internal power MOSFET switches.
16 PGND power_in Power ground.
17 PVIN power_in Power supply voltage input; requires a bypass capacitor to GND.
18 EN/DLY input Enable input that starts the part above the enable threshold, with a 1 µA source to VDD so a capacitor can set a delay; low quiescent current mode below threshold.
19 DELAY input Capacitor to ground sets the internal delay timer that delays POR at turn-on and ramp down at turn-off.
20 RC passive Ramp control: capacitor to ground sets output voltage slew rate at start-up, usable for tracking and soft start.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package QFN-20-EP(4x3)
Category Power Supply Chip
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage Range VIN 2.6 5.5 V 3
Undervoltage Lockout Threshold 2.4 2.5 2.6 V Turn-on 3
UVLO Hysteresis 280 mV 3
Quiescent Current, PWM Mode 1.3 2 mA VEN ≥ 1.34V; VFB = 0.9V (not switching) 3
Shutdown Current ISHDN 5 10 μA VEN = 0V 3
Adjustable Feedback Voltage VFB 0.693 0.7 0.707 V ±1% 3
Adjustable Feedback Voltage (over temperature) VFB 0.686 0.7 0.714 V ±2% (over temperature) 3
Oscillator Frequency 0.8 1 1.2 MHz 3
Current Limit ILIM 4 7 10 A VFB = 0.5V 3
Maximum Duty Cycle 100 % VFB ≤ 0.5V 3
EN/DLY Threshold Voltage 1.14 1.24 1.34 V 3
EN/DLY Source Current 0.6 1 1.8 μA VIN = 2.6 to VIN = 5.5V 3
RC Pin Ramp Control Current IRAMP 0.5 1 1.7 μA Ramp Control Current 3
POR Leakage Current IPOR(LEAK) 1 μA VPORH = 5.5V; POR = High 4
POR Leakage Current (over temperature) IPOR(LEAK) 2 μA VPORH = 5.5V; POR = High 4
POR Threshold, Percent of VOUT below nominal VPOR 7.5 10 12.5 % Threshold, Percent of VOUT below nominal 4
Junction Temperature Range TJ -40 125 °C 4
Storage Temperature Range TS -65 150 °C 4
Lead Temperature 260 °C 4
PVIN to PGND -0.3 6 V 3
VSW to PGND VSW -0.3 V upper limit PVIN 3
VEN/DLY to PGND VEN/DLY -0.3 V upper limit PVIN 3
VPG to PGND VPG -0.3 V upper limit PVIN 3
Output Voltage Line Regulation 0.2 % VOUT = 1.2V; VIN = 2.6 to 5.5V, ILOAD = 100 mA 3
Output Voltage Load Regulation 0.2 % 100 mA < ILOAD < 4000 mA, VIN = 3.3V 3
Switch ON-Resistance PFET 0.06 Ω ISW = 1000 mA; VFB = 0.5V 3
Switch ON-Resistance NFET 0.035 Ω ISW = 1000 mA; VFB = 0.9V 3
Overtemperature Shutdown 150 °C 4
Thermal Resistance, QFN 20-Ld θJA 45 °C/W 4

CAD (KiCad official)

  • Symbol: MIC22400YML-TR
  • Footprint: Package_DFN_QFN:QFN-20-1EP_3x4mm_P0.5mm_EP1.65x2.65mm
  • 3D model: QFN-20-EP(4x3) (KiCad packages3D, STEP)
  • 3D model files: mic22400yml-tr-etched.step / mic22400yml-tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mic22400yml-tr.step / mic22400yml-tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (28 pp, sha256 116f93dc85fe0726, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF