Generated by kicad-footprint-generator · KiCad file format 20260206
MIC22400YML-TR
Microchip Tech · DC-DC Converters · QFN-20-EP(4x3)
MIC22400YML-TR from Microchip Tech, in a QFN-20-EP(4x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | POR | output | Power-On-Reset open-drain output indicating when the output is out of regulation, active after the delay set by the DELAY pin. |
| 2 | CF | passive | Adjustable frequency set with an external capacitor. |
| 3 | NC | unconnected | Not connected internally. |
| 4 | COMP | input | Compensation pin; place an RC to GND to compensate the device. |
| 5 | NC | unconnected | Not connected internally. |
| 6 | FB | input | Feedback input to the error amplifier, connected to the external resistor divider that sets the output voltage. |
| 7 | SGND | power_in | Signal ground. |
| 8 | SVIN | power_in | Signal power supply voltage input; requires a bypass capacitor to GND. |
| 9 | NC | unconnected | Not connected internally. |
| 10 | PVIN | power_in | Power supply voltage input; requires a bypass capacitor to GND. |
| 11 | PGND | power_in | Power ground. |
| 12 | SW | power_out | Switch output from the internal power MOSFET switches. |
| 13 | SW | power_out | Switch output from the internal power MOSFET switches. |
| 14 | SW | power_out | Switch output from the internal power MOSFET switches. |
| 15 | SW | power_out | Switch output from the internal power MOSFET switches. |
| 16 | PGND | power_in | Power ground. |
| 17 | PVIN | power_in | Power supply voltage input; requires a bypass capacitor to GND. |
| 18 | EN/DLY | input | Enable input that starts the part above the enable threshold, with a 1 µA source to VDD so a capacitor can set a delay; low quiescent current mode below threshold. |
| 19 | DELAY | input | Capacitor to ground sets the internal delay timer that delays POR at turn-on and ramp down at turn-off. |
| 20 | RC | passive | Ramp control: capacitor to ground sets output voltage slew rate at start-up, usable for tracking and soft start. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-20-EP(4x3) |
| Category | Power Supply Chip |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage Range | VIN | 2.6 | 5.5 | V | 3 | ||
| Undervoltage Lockout Threshold | 2.4 | 2.5 | 2.6 | V | Turn-on | 3 | |
| UVLO Hysteresis | 280 | mV | 3 | ||||
| Quiescent Current, PWM Mode | 1.3 | 2 | mA | VEN ≥ 1.34V; VFB = 0.9V (not switching) | 3 | ||
| Shutdown Current | ISHDN | 5 | 10 | μA | VEN = 0V | 3 | |
| Adjustable Feedback Voltage | VFB | 0.693 | 0.7 | 0.707 | V | ±1% | 3 |
| Adjustable Feedback Voltage (over temperature) | VFB | 0.686 | 0.7 | 0.714 | V | ±2% (over temperature) | 3 |
| Oscillator Frequency | 0.8 | 1 | 1.2 | MHz | 3 | ||
| Current Limit | ILIM | 4 | 7 | 10 | A | VFB = 0.5V | 3 |
| Maximum Duty Cycle | 100 | % | VFB ≤ 0.5V | 3 | |||
| EN/DLY Threshold Voltage | 1.14 | 1.24 | 1.34 | V | 3 | ||
| EN/DLY Source Current | 0.6 | 1 | 1.8 | μA | VIN = 2.6 to VIN = 5.5V | 3 | |
| RC Pin Ramp Control Current | IRAMP | 0.5 | 1 | 1.7 | μA | Ramp Control Current | 3 |
| POR Leakage Current | IPOR(LEAK) | 1 | μA | VPORH = 5.5V; POR = High | 4 | ||
| POR Leakage Current (over temperature) | IPOR(LEAK) | 2 | μA | VPORH = 5.5V; POR = High | 4 | ||
| POR Threshold, Percent of VOUT below nominal | VPOR | 7.5 | 10 | 12.5 | % | Threshold, Percent of VOUT below nominal | 4 |
| Junction Temperature Range | TJ | -40 | 125 | °C | 4 | ||
| Storage Temperature Range | TS | -65 | 150 | °C | 4 | ||
| Lead Temperature | 260 | °C | 4 | ||||
| PVIN to PGND | -0.3 | 6 | V | 3 | |||
| VSW to PGND | VSW | -0.3 | V | upper limit PVIN | 3 | ||
| VEN/DLY to PGND | VEN/DLY | -0.3 | V | upper limit PVIN | 3 | ||
| VPG to PGND | VPG | -0.3 | V | upper limit PVIN | 3 | ||
| Output Voltage Line Regulation | 0.2 | % | VOUT = 1.2V; VIN = 2.6 to 5.5V, ILOAD = 100 mA | 3 | |||
| Output Voltage Load Regulation | 0.2 | % | 100 mA < ILOAD < 4000 mA, VIN = 3.3V | 3 | |||
| Switch ON-Resistance PFET | 0.06 | Ω | ISW = 1000 mA; VFB = 0.5V | 3 | |||
| Switch ON-Resistance NFET | 0.035 | Ω | ISW = 1000 mA; VFB = 0.9V | 3 | |||
| Overtemperature Shutdown | 150 | °C | 4 | ||||
| Thermal Resistance, QFN 20-Ld | θJA | 45 | °C/W | 4 |
CAD (KiCad official)
- Symbol:
MIC22400YML-TR - Footprint:
Package_DFN_QFN:QFN-20-1EP_3x4mm_P0.5mm_EP1.65x2.65mm - 3D model: QFN-20-EP(4x3) (KiCad packages3D, STEP)
- 3D model files:
mic22400yml-tr-etched.step/mic22400yml-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic22400yml-tr.step/mic22400yml-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (28 pp, sha256
116f93dc85fe0726, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).