main
History Download
Ray Publish 0.1.0 2d5d3b5

MIC2186YQS

Microchip Tech · DC-DC Converters · QSOP-16-150mil

MIC2186YQS from Microchip Tech, in a QSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VINA power_in Input voltage to control circuitry, 2.9V to 14V.
2 SKIP input Regulator operates in PWM mode when pulled low and in skip mode when raised to VDD; there is no automatic switching between PWM and skip mode on this device.
3 SS passive Soft start reduces the inrush current and slows the output voltage rise time, with a 5uA current source charging the capacitor up to VDD.
4 COMP passive Internal error amplifier output that connects to a capacitor or series RC network to compensate the control loop.
5 SGND power_in Small signal ground that must be routed separately from other grounds to the negative terminal of COUT.
6 FB input Feedback input that regulates FB to 1.245V.
7 EN/UVLO input Low level powers down the device and reduces quiescent current to under 0.5uA; below 1.5V disables output switching with 135mV hysteresis, and below 0.9V forces complete micropower shutdown.
8 VREF power_out Provides the 1.245V reference, which should be bypassed to SGND with a 0.1uF capacitor.
9 CSH input Positive input to the current limit comparator; a built-in 100mV offset to SGND with the current sense resistor sets the current limit threshold.
10 VDD power_out 3V internal linear regulator output that is also the supply bus for the chip, bypassed to SGND with 1uF and limited to a maximum source current of 0.5mA.
11 SYNC input Frequency synchronization input where the leading edge above 1.5V starts a switching cycle; connect to SGND if not used.
12 PGND power_in MOSFET driver power ground that connects to the bottom of the current sense resistor and the negative terminal of CIN.
13 HIDC input High duty cycle select: logic HIGH sets 85% maximum duty cycle and logic LOW sets 50% maximum duty cycle, together with FREQ/2.
14 OUTN output High current drive for an N-channel MOSFET with voltage swing from ground to VIN and typical RON of 1.6 ohm.
15 FREQ/2 input Sets duty cycle and frequency along with HIDC.
16 VINP power_in Power input voltage to the gate drive circuitry, 2.9V to 14V, normally connected to the output voltage.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package QSOP-16-150mil
Category Power Supply Chip
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Feedback Voltage Reference VFB 1.233 1.245 1.258 V ±1% 3
Feedback Voltage Reference VFB 1.22 1.27 V ±2% 3
Feedback Voltage Reference VFB 1.208 1.245 1.282 V 3V ≤ VINA ≤ 9V; 0mV ≤ CSH ≤ 75mV; ±3% 3
Feedback Bias Current 50 nA 3
VINA Input Current, PWM mode 0.7 mA VSKIP = 0V 3
VINP Input Current, PWM mode 2.8 mA VSKIP = 0V (excluding external MOSFET gate current) 3
VINA Input Current, SKIP mode 0.6 mA VSKIP = 5V 3
Shutdown Quiescent Current 0.5 5 µA VEN/UVLO = 0V; (IVINA + IVINP) 3
Digital Supply Voltage (VDD) VDD 2.82 3 3.18 V IL = 0 3
Reference Voltage VREF 1.226 1.245 1.264 V ±1.5% 3
Reference Voltage VREF 1.213 1.276 V ±2.5% 3
Enable Input Threshold 0.6 0.9 1.2 V 4
UVLO Threshold 1.4 1.5 1.6 V 4
Enable Input Current 0.2 5 µA VEN/UVLO = 5V 4
Current Limit Threshold Voltage 80 100 120 mV Voltage on CSH to trip current limit 4
SKIP Threshold 0.6 1.4 2.2 V 4
SKIP Input Current 0.1 5 µA VSKIP = 3V 4
HIDC Threshold 0.6 1.4 2.2 V 4
Oscillator Frequency fO 360 400 440 kHz 4
Maximum Duty Cycle 85 % VFB = 1.0V, VHIDC = 3V 4
Maximum Duty Cycle 50 % VFB = 1.0V, VHIDC = 0V 4
FREQ/2 Frequency fO 170 200 230 kHz VHiDC = 3V, VFREQ/2 = 3V 4
SYNC Threshold Level 0.6 1.4 2.2 V 4
SYNC Input Current 0.1 5 µA 4
SYNC Capture Range fO 600 kHz Note 4; fO + 15% 4
Output Driver Impedance (source) 1.8 4 Ω VINP = 12V 4
Output Driver Impedance (sink) 1.6 3.5 Ω VINP = 12V 4
Output Driver Impedance (sink) 2.4 Ω VINP = 5V 4
Supply Voltage (VINA, VINP) VINA, VINP 15 V 3
Digital Supply Voltage (VDD) VDD 7 V 3
SKIP Pin Voltage VSKIP -0.3 7 V 3
Max Duty Cycle Pin Voltage VHIDC -0.3 7 V 3
Frequency Divider Pin Voltage VFREQ/2 -0.3 7 V 3
Sync Pin Voltage VSYNC -0.3 7 V 3
Comp Pin Voltage VCOMP -0.3 3 V 3
Feedback Pin Voltage VFB -0.3 3 V 3
Enable Pin Voltage VEN/UVLO -0.3 15 V 3
Current Sense Voltage VCSH -0.3 1 V 3
Power Dissipation (16 lead QSOP) PD 245 mW @ TA = 85°C 3
Ambient Storage Temperature -65 150 °C 3
Supply Voltage (VINA, VINP) VINA, VINP 2.9 14 V 3
Operating Ambient Temperature TA -40 85 °C 3
Junction Temperature TJ -40 125 °C 3
Thermal Resistance, junction-to-ambient (16-lead QSOP) θJA 163 °C/W 3

CAD (KiCad official)

  • Symbol: MIC2186YQS
  • Footprint: Package_SO:QSOP-16_3.9x4.9mm_P0.635mm
  • 3D model: QSOP-16-150mil (KiCad packages3D, STEP)
  • 3D model files: mic2186yqs-etched.step / mic2186yqs-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mic2186yqs.step / mic2186yqs.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (15 pp, sha256 8eedcc96ee925013, retrieved 2026-10-28, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF