Generated by kicad-footprint-generator · KiCad file format 20260206
MIC2186YQS
Microchip Tech · DC-DC Converters · QSOP-16-150mil
MIC2186YQS from Microchip Tech, in a QSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VINA | power_in | Input voltage to control circuitry, 2.9V to 14V. |
| 2 | SKIP | input | Regulator operates in PWM mode when pulled low and in skip mode when raised to VDD; there is no automatic switching between PWM and skip mode on this device. |
| 3 | SS | passive | Soft start reduces the inrush current and slows the output voltage rise time, with a 5uA current source charging the capacitor up to VDD. |
| 4 | COMP | passive | Internal error amplifier output that connects to a capacitor or series RC network to compensate the control loop. |
| 5 | SGND | power_in | Small signal ground that must be routed separately from other grounds to the negative terminal of COUT. |
| 6 | FB | input | Feedback input that regulates FB to 1.245V. |
| 7 | EN/UVLO | input | Low level powers down the device and reduces quiescent current to under 0.5uA; below 1.5V disables output switching with 135mV hysteresis, and below 0.9V forces complete micropower shutdown. |
| 8 | VREF | power_out | Provides the 1.245V reference, which should be bypassed to SGND with a 0.1uF capacitor. |
| 9 | CSH | input | Positive input to the current limit comparator; a built-in 100mV offset to SGND with the current sense resistor sets the current limit threshold. |
| 10 | VDD | power_out | 3V internal linear regulator output that is also the supply bus for the chip, bypassed to SGND with 1uF and limited to a maximum source current of 0.5mA. |
| 11 | SYNC | input | Frequency synchronization input where the leading edge above 1.5V starts a switching cycle; connect to SGND if not used. |
| 12 | PGND | power_in | MOSFET driver power ground that connects to the bottom of the current sense resistor and the negative terminal of CIN. |
| 13 | HIDC | input | High duty cycle select: logic HIGH sets 85% maximum duty cycle and logic LOW sets 50% maximum duty cycle, together with FREQ/2. |
| 14 | OUTN | output | High current drive for an N-channel MOSFET with voltage swing from ground to VIN and typical RON of 1.6 ohm. |
| 15 | FREQ/2 | input | Sets duty cycle and frequency along with HIDC. |
| 16 | VINP | power_in | Power input voltage to the gate drive circuitry, 2.9V to 14V, normally connected to the output voltage. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QSOP-16-150mil |
| Category | Power Supply Chip |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Feedback Voltage Reference | VFB | 1.233 | 1.245 | 1.258 | V | ±1% | 3 |
| Feedback Voltage Reference | VFB | 1.22 | 1.27 | V | ±2% | 3 | |
| Feedback Voltage Reference | VFB | 1.208 | 1.245 | 1.282 | V | 3V ≤ VINA ≤ 9V; 0mV ≤ CSH ≤ 75mV; ±3% | 3 |
| Feedback Bias Current | 50 | nA | 3 | ||||
| VINA Input Current, PWM mode | 0.7 | mA | VSKIP = 0V | 3 | |||
| VINP Input Current, PWM mode | 2.8 | mA | VSKIP = 0V (excluding external MOSFET gate current) | 3 | |||
| VINA Input Current, SKIP mode | 0.6 | mA | VSKIP = 5V | 3 | |||
| Shutdown Quiescent Current | 0.5 | 5 | µA | VEN/UVLO = 0V; (IVINA + IVINP) | 3 | ||
| Digital Supply Voltage (VDD) | VDD | 2.82 | 3 | 3.18 | V | IL = 0 | 3 |
| Reference Voltage | VREF | 1.226 | 1.245 | 1.264 | V | ±1.5% | 3 |
| Reference Voltage | VREF | 1.213 | 1.276 | V | ±2.5% | 3 | |
| Enable Input Threshold | 0.6 | 0.9 | 1.2 | V | 4 | ||
| UVLO Threshold | 1.4 | 1.5 | 1.6 | V | 4 | ||
| Enable Input Current | 0.2 | 5 | µA | VEN/UVLO = 5V | 4 | ||
| Current Limit Threshold Voltage | 80 | 100 | 120 | mV | Voltage on CSH to trip current limit | 4 | |
| SKIP Threshold | 0.6 | 1.4 | 2.2 | V | 4 | ||
| SKIP Input Current | 0.1 | 5 | µA | VSKIP = 3V | 4 | ||
| HIDC Threshold | 0.6 | 1.4 | 2.2 | V | 4 | ||
| Oscillator Frequency | fO | 360 | 400 | 440 | kHz | 4 | |
| Maximum Duty Cycle | 85 | % | VFB = 1.0V, VHIDC = 3V | 4 | |||
| Maximum Duty Cycle | 50 | % | VFB = 1.0V, VHIDC = 0V | 4 | |||
| FREQ/2 Frequency | fO | 170 | 200 | 230 | kHz | VHiDC = 3V, VFREQ/2 = 3V | 4 |
| SYNC Threshold Level | 0.6 | 1.4 | 2.2 | V | 4 | ||
| SYNC Input Current | 0.1 | 5 | µA | 4 | |||
| SYNC Capture Range | fO | 600 | kHz | Note 4; fO + 15% | 4 | ||
| Output Driver Impedance (source) | 1.8 | 4 | Ω | VINP = 12V | 4 | ||
| Output Driver Impedance (sink) | 1.6 | 3.5 | Ω | VINP = 12V | 4 | ||
| Output Driver Impedance (sink) | 2.4 | Ω | VINP = 5V | 4 | |||
| Supply Voltage (VINA, VINP) | VINA, VINP | 15 | V | 3 | |||
| Digital Supply Voltage (VDD) | VDD | 7 | V | 3 | |||
| SKIP Pin Voltage | VSKIP | -0.3 | 7 | V | 3 | ||
| Max Duty Cycle Pin Voltage | VHIDC | -0.3 | 7 | V | 3 | ||
| Frequency Divider Pin Voltage | VFREQ/2 | -0.3 | 7 | V | 3 | ||
| Sync Pin Voltage | VSYNC | -0.3 | 7 | V | 3 | ||
| Comp Pin Voltage | VCOMP | -0.3 | 3 | V | 3 | ||
| Feedback Pin Voltage | VFB | -0.3 | 3 | V | 3 | ||
| Enable Pin Voltage | VEN/UVLO | -0.3 | 15 | V | 3 | ||
| Current Sense Voltage | VCSH | -0.3 | 1 | V | 3 | ||
| Power Dissipation (16 lead QSOP) | PD | 245 | mW | @ TA = 85°C | 3 | ||
| Ambient Storage Temperature | -65 | 150 | °C | 3 | |||
| Supply Voltage (VINA, VINP) | VINA, VINP | 2.9 | 14 | V | 3 | ||
| Operating Ambient Temperature | TA | -40 | 85 | °C | 3 | ||
| Junction Temperature | TJ | -40 | 125 | °C | 3 | ||
| Thermal Resistance, junction-to-ambient (16-lead QSOP) | θJA | 163 | °C/W | 3 |
CAD (KiCad official)
- Symbol:
MIC2186YQS - Footprint:
Package_SO:QSOP-16_3.9x4.9mm_P0.635mm - 3D model: QSOP-16-150mil (KiCad packages3D, STEP)
- 3D model files:
mic2186yqs-etched.step/mic2186yqs-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic2186yqs.step/mic2186yqs.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (15 pp, sha256
8eedcc96ee925013, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).