main
History Download
Ray Publish 0.1.0 06bd527

MIC2042-1YTS

Microchip Tech · Power Management Specialized - PMIC · TSSOP-14

MIC2042-1YTS from Microchip Tech, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 PWRGD output Power-good output, active high, open-drain, asserts high when the voltage at PGREF exceeds its threshold; needs an external pull-up to a rail of 6V maximum.
2 EN input Switch enable input controlling the output MOSFET gate, active high (-1) or active low (-2); must be driven to a defined logic level, not left floating, and not exceed VBIAS or go below ground.
3 /FAULT output Active-low open-drain N-channel fault status output indicating overcurrent (asserted after the 28ms flag delay) or thermal shutdown, with a pull-up to a maximum 6V rail.
4 UVLOIN input Undervoltage lockout adjust input; left open the UVLO threshold is 1.45V, and an external divider (total resistance below 200kΩ) lowers the threshold when VIN is below 1.6V.
5 GND power_in Ground connection, tie to analog ground.
6 ILIM passive Current limit set pin where a resistor RSET to ground sets the limit as CLF/RSET, for a continuous output current range of 0.5A to 3A.
7 VBIAS power_in Bias supply input powering the switch and internal circuitry, with a range of 1.6V to 5.5V; connect to VIN externally for single-supply use when VIN is 1.6V to 5.5V.
8 VIN power_in Switch input supply (drain of the output MOSFET) with a range of 0.8V to 5.5V, which must be externally tied to the other VIN pin (pin 12).
9 SLEW passive Slew-rate control input where a capacitor to ground (16V rating or greater, 25V recommended) slows the output slew rate, keeping turn-on time below the 28ms flag delay.
10 VOUT power_out Switch output (source of the output MOSFET), which must be externally tied to the other VOUT pins (11, 14).
11 VOUT power_out Switch output (source of the output MOSFET), which must be externally tied to the other VOUT pins (10, 14).
12 VIN power_in Switch input supply (drain of the output MOSFET) with a range of 0.8V to 5.5V, which must be externally tied to the other VIN pin (pin 8).
13 PGREF input Power-good threshold input where an external divider sets the VOUT level at which the threshold VTH (205 to 245mV) is exceeded; tie to VOUT when PWRGD is unused.
14 VOUT power_out Switch output (source of the output MOSFET), which must be externally tied to the other VOUT pins (10, 11).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package TSSOP-14
Category Power Supply Chip
Pins 14

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Switch Input Voltage (14-pin TSSOP) VIN 0.8 5.5 V VIN ≤ VBIAS, 14-pin TSSOP 4
Bias Supply Voltage (14-pin TSSOP) VBIAS 1.6 5.5 V 4
VBIAS Supply Current - Switch OFF IBIAS 0.1 5 µA No load 4
VBIAS Supply Current - Switch ON IBIAS 300 400 µA No load 4
Enable Input Current IEN -1 0.01 1 µA VEN = 0V to 5.5V 4
Enable Input Threshold Hysteresis VENHYST 100 mV 4
Switch Resistance RDS(ON) 40 60 mΩ VIN = VBIAS = 3V, 5V; IOUT = 500mA 4
Output Leakage Current ILEAK 10 µA Output off 4
Current Limit Factor (5V) CLF 310 395 485 A×Ω VIN = 5V, 0.5V ≤ VOUT < 0.5VIN, 0.5A ≤ IOUT ≤ 3A 4
Current Limit Factor (3V) CLF 320 385 450 A×Ω VIN = 3V, 0.5V ≤ VOUT < 0.5VIN, 0.5A ≤ IOUT ≤ 3A 4
PGREF and UVLOIN Threshold VTH 205 225 245 mV VIN = VBIAS = 1.6V to 5.5V (14-pin TSSOP) 4
Output Low Voltage VOL 0.4 V IOL (/FAULT) = 15mA; IOL (PWRGD) = 5mA 4
/FAULT, PWRGD Off Current IOFF 1 µA VFAULT = VPWRGD = 5V 4
Undervoltage Lockout Threshold (rising) VUV 1.3 1.45 1.58 V VIN rising 4
Undervoltage Lockout Threshold (falling) VUV 1.2 1.35 1.5 V VIN falling 4
Undervoltage Lockout Threshold Hysteresis VUVHYST 100 mV 4
UVLO Adjust Pin Threshold Voltage (rising) VUVINTH 205 225 245 mV VIN rising 4
UVLO Adjust Pin Threshold Voltage (falling) VUVINTH 185 205 225 mV VIN falling 4
UVLO Adjust Pin Threshold Hysteresis VUVINHYST 20 mV 4
Overtemperature Threshold (increasing) 140 °C TJ increasing 4
Overtemperature Threshold (decreasing) 120 °C TJ decreasing 4
Flag Response Delay tFLAG 21 28 35 ms VIN = VBIAS = 3V, 5V 5
Output Turn-on Delay tON 600 800 1000 µs RLOAD = 10Ω, CLOAD = 1µF 5
Output Turn-on Rise Time tR 1 1.5 2 ms RLOAD = 10Ω, CLOAD = 1µF 5
Output Turn-off Delay tOFF 15 µs RLOAD = 10Ω, CLOAD = 1µF 5
Output Turn-off Fall Time tF 24 µs RLOAD = 10Ω, CLOAD = 1µF 5
Supply Voltage VIN and VBIAS VIN, VBIAS 6 V 4
/FAULT, PWRGD Output Voltage 6 V 4
/FAULT, PWRGD Output Current 25 mA 4
ESD Rating Human Body Model 3 kV Human Body Model 4
ESD Rating Machine Model 200 V Machine Model 4
Operating Supply Voltage VIN VIN 0.8 5.5 V 4
Operating Supply Voltage VBIAS VBIAS 1.6 5.5 V 4
Continuous Output Current IOUT 0.5 3 A 4
Ambient Temperature TA -40 85 °C 4
Package Thermal Resistance TSSOP θJA 85 °C/W TSSOP 4

CAD (KiCad official)

  • Symbol: MIC2042-1YTS
  • Footprint: Package_SO:TSSOP-14_4.4x5mm_P0.65mm
  • 3D model: TSSOP-14 (KiCad packages3D, STEP)
  • 3D model files: mic2042-1yts-etched.step / mic2042-1yts-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mic2042-1yts.step / mic2042-1yts.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (15 pp, sha256 f1f2f59ea931a67c, retrieved 2026-10-30, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF