Generated by kicad-footprint-generator · KiCad file format 20260206
MIC2042-1YTS
Microchip Tech · Power Management Specialized - PMIC · TSSOP-14
MIC2042-1YTS from Microchip Tech, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PWRGD | output | Power-good output, active high, open-drain, asserts high when the voltage at PGREF exceeds its threshold; needs an external pull-up to a rail of 6V maximum. |
| 2 | EN | input | Switch enable input controlling the output MOSFET gate, active high (-1) or active low (-2); must be driven to a defined logic level, not left floating, and not exceed VBIAS or go below ground. |
| 3 | /FAULT | output | Active-low open-drain N-channel fault status output indicating overcurrent (asserted after the 28ms flag delay) or thermal shutdown, with a pull-up to a maximum 6V rail. |
| 4 | UVLOIN | input | Undervoltage lockout adjust input; left open the UVLO threshold is 1.45V, and an external divider (total resistance below 200kΩ) lowers the threshold when VIN is below 1.6V. |
| 5 | GND | power_in | Ground connection, tie to analog ground. |
| 6 | ILIM | passive | Current limit set pin where a resistor RSET to ground sets the limit as CLF/RSET, for a continuous output current range of 0.5A to 3A. |
| 7 | VBIAS | power_in | Bias supply input powering the switch and internal circuitry, with a range of 1.6V to 5.5V; connect to VIN externally for single-supply use when VIN is 1.6V to 5.5V. |
| 8 | VIN | power_in | Switch input supply (drain of the output MOSFET) with a range of 0.8V to 5.5V, which must be externally tied to the other VIN pin (pin 12). |
| 9 | SLEW | passive | Slew-rate control input where a capacitor to ground (16V rating or greater, 25V recommended) slows the output slew rate, keeping turn-on time below the 28ms flag delay. |
| 10 | VOUT | power_out | Switch output (source of the output MOSFET), which must be externally tied to the other VOUT pins (11, 14). |
| 11 | VOUT | power_out | Switch output (source of the output MOSFET), which must be externally tied to the other VOUT pins (10, 14). |
| 12 | VIN | power_in | Switch input supply (drain of the output MOSFET) with a range of 0.8V to 5.5V, which must be externally tied to the other VIN pin (pin 8). |
| 13 | PGREF | input | Power-good threshold input where an external divider sets the VOUT level at which the threshold VTH (205 to 245mV) is exceeded; tie to VOUT when PWRGD is unused. |
| 14 | VOUT | power_out | Switch output (source of the output MOSFET), which must be externally tied to the other VOUT pins (10, 11). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TSSOP-14 |
| Category | Power Supply Chip |
| Pins | 14 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Switch Input Voltage (14-pin TSSOP) | VIN | 0.8 | 5.5 | V | VIN ≤ VBIAS, 14-pin TSSOP | 4 | |
| Bias Supply Voltage (14-pin TSSOP) | VBIAS | 1.6 | 5.5 | V | 4 | ||
| VBIAS Supply Current - Switch OFF | IBIAS | 0.1 | 5 | µA | No load | 4 | |
| VBIAS Supply Current - Switch ON | IBIAS | 300 | 400 | µA | No load | 4 | |
| Enable Input Current | IEN | -1 | 0.01 | 1 | µA | VEN = 0V to 5.5V | 4 |
| Enable Input Threshold Hysteresis | VENHYST | 100 | mV | 4 | |||
| Switch Resistance | RDS(ON) | 40 | 60 | mΩ | VIN = VBIAS = 3V, 5V; IOUT = 500mA | 4 | |
| Output Leakage Current | ILEAK | 10 | µA | Output off | 4 | ||
| Current Limit Factor (5V) | CLF | 310 | 395 | 485 | A×Ω | VIN = 5V, 0.5V ≤ VOUT < 0.5VIN, 0.5A ≤ IOUT ≤ 3A | 4 |
| Current Limit Factor (3V) | CLF | 320 | 385 | 450 | A×Ω | VIN = 3V, 0.5V ≤ VOUT < 0.5VIN, 0.5A ≤ IOUT ≤ 3A | 4 |
| PGREF and UVLOIN Threshold | VTH | 205 | 225 | 245 | mV | VIN = VBIAS = 1.6V to 5.5V (14-pin TSSOP) | 4 |
| Output Low Voltage | VOL | 0.4 | V | IOL (/FAULT) = 15mA; IOL (PWRGD) = 5mA | 4 | ||
| /FAULT, PWRGD Off Current | IOFF | 1 | µA | VFAULT = VPWRGD = 5V | 4 | ||
| Undervoltage Lockout Threshold (rising) | VUV | 1.3 | 1.45 | 1.58 | V | VIN rising | 4 |
| Undervoltage Lockout Threshold (falling) | VUV | 1.2 | 1.35 | 1.5 | V | VIN falling | 4 |
| Undervoltage Lockout Threshold Hysteresis | VUVHYST | 100 | mV | 4 | |||
| UVLO Adjust Pin Threshold Voltage (rising) | VUVINTH | 205 | 225 | 245 | mV | VIN rising | 4 |
| UVLO Adjust Pin Threshold Voltage (falling) | VUVINTH | 185 | 205 | 225 | mV | VIN falling | 4 |
| UVLO Adjust Pin Threshold Hysteresis | VUVINHYST | 20 | mV | 4 | |||
| Overtemperature Threshold (increasing) | 140 | °C | TJ increasing | 4 | |||
| Overtemperature Threshold (decreasing) | 120 | °C | TJ decreasing | 4 | |||
| Flag Response Delay | tFLAG | 21 | 28 | 35 | ms | VIN = VBIAS = 3V, 5V | 5 |
| Output Turn-on Delay | tON | 600 | 800 | 1000 | µs | RLOAD = 10Ω, CLOAD = 1µF | 5 |
| Output Turn-on Rise Time | tR | 1 | 1.5 | 2 | ms | RLOAD = 10Ω, CLOAD = 1µF | 5 |
| Output Turn-off Delay | tOFF | 15 | µs | RLOAD = 10Ω, CLOAD = 1µF | 5 | ||
| Output Turn-off Fall Time | tF | 24 | µs | RLOAD = 10Ω, CLOAD = 1µF | 5 | ||
| Supply Voltage VIN and VBIAS | VIN, VBIAS | 6 | V | 4 | |||
| /FAULT, PWRGD Output Voltage | 6 | V | 4 | ||||
| /FAULT, PWRGD Output Current | 25 | mA | 4 | ||||
| ESD Rating Human Body Model | 3 | kV | Human Body Model | 4 | |||
| ESD Rating Machine Model | 200 | V | Machine Model | 4 | |||
| Operating Supply Voltage VIN | VIN | 0.8 | 5.5 | V | 4 | ||
| Operating Supply Voltage VBIAS | VBIAS | 1.6 | 5.5 | V | 4 | ||
| Continuous Output Current | IOUT | 0.5 | 3 | A | 4 | ||
| Ambient Temperature | TA | -40 | 85 | °C | 4 | ||
| Package Thermal Resistance TSSOP | θJA | 85 | °C/W | TSSOP | 4 |
CAD (KiCad official)
- Symbol:
MIC2042-1YTS - Footprint:
Package_SO:TSSOP-14_4.4x5mm_P0.65mm - 3D model: TSSOP-14 (KiCad packages3D, STEP)
- 3D model files:
mic2042-1yts-etched.step/mic2042-1yts-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic2042-1yts.step/mic2042-1yts.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (15 pp, sha256
f1f2f59ea931a67c, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).