MD8942

{
 "schema": "adom.pads/1",
 "slug": "md8942",
 "footprint": "SOT-23-6",
 "generated_from": {
  "footprint": "SOT-23-6@sha256:f341c73aac9dcb55",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -1.1375,
   -0.95
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOT-23-6@sha256:f341c73aac9dcb55"
 },
 "pad_count": 6,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5",
  "6"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "BST",
   "type": "passive",
   "description": "Bootstrap pin providing gate-drive bias for the internal high-side switch FET. Connect a bootstrap capacitor (Cboot) between BST and SW. Absolute max BST-to-SW voltage is 6V; internally charged to ~5V from VCB through a diode.",
   "is_pin1": true,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "GND",
   "type": "power_in",
   "description": "Device ground connection. Should be connected as close as possible to the output capacitor to avoid high current switching paths and to serve as the reference for feedback and enable.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "FB",
   "type": "input",
   "description": "Feedback input to the internal error amplifier. Set the output voltage via a resistor divider from VOUT to FB using VOUT = VFB × (1 + R2/R1), where VFB is typically 0.794V. Absolute max -0.3V to 6V.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "EN",
   "type": "input",
   "description": "Enable input, active-high logic. Pulling EN above the ~1V rising threshold enables the chip; pulling below the falling threshold (~0.84V, 160mV hysteresis) shuts it down. Floating EN disables the chip (internal 430kΩ pull-down to GND). Internal zener clamps EN to ~5V, absolute max 6V, sink current limit 100µA.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "VIN",
   "type": "power_in",
   "description": "Input supply pin. Operating range 4V to 36V, standoff input voltage 42V. Bypass with a low-ESR ceramic input capacitor (typ. 10µF) placed as close as possible to VIN and GND.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "6",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "6",
   "name": "SW",
   "type": "output",
   "description": "Switch node - the output of the internal high-side and low-side power MOSFETs. Connect to the external inductor and to the bootstrap capacitor's low side. Absolute max -0.3V to VIN(MAX)+0.3V.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-6.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}