main
Ray
Publish 0.1.0
eaaae41
MCP79520T-I
Microchip Tech · Real-time Clocks (RTC) · MSOP-10
MCP79520T-I from Microchip Tech, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | X1 | input | Quartz crystal input for a 32.768 kHz crystal (optimized for 6-9 pF load), also the external clock input when configured for an external oscillator. |
| 2 | X2 | output | Quartz crystal output for the 32.768 kHz crystal; leave floating when using an external clock on X1. |
| 3 | VBAT | power_in | Battery backup supply input (1.3V to 3.6V) maintaining RTCC and SRAM when VCC is unavailable; connect to VSS if unused. |
| 4 | CS | input | Chip select input, active low selects the device and high deselects it, placing SO in high impedance. |
| 5 | VSS | power_in | Ground. |
| 6 | SI | input | Serial data input receiving instructions, addresses and data, latched on the rising edge of SCK. |
| 7 | SO | tri_state | Serial data output shifted out after the falling edge of SCK, high-impedance when CS is deselected. |
| 8 | SCK | input | Serial clock input synchronizing SPI communication, up to 5 MHz. |
| 9 | MFP | bidirectional | Multifunction pin shared by clock output and alarms; requires an external pull-up to VCC or VBAT and has a maximum sink current of 10 mA. |
| 10 | VCC | power_in | Primary power supply, operating range 1.8V to 3.6V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-10 |
| Category | RTC/Clock Chip |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| All inputs and outputs w.r.t. VSS (lower limit; upper limit VCC+1.0V) | -0.6 | V | -0.6V to VCC+1.0V | 4 | |||
| Storage temperature | -65 | 150 | °C | 4 | |||
| Ambient temperature under bias | -40 | 85 | °C | 4 | |||
| ESD protection on all pins | 4 | kV | 4 | ||||
| Operating supply voltage | VCC | 1.8 | 3.6 | V | Industrial (I) | 4 | |
| Operating temperature | TA | -40 | 85 | °C | Industrial (I) | 4 | |
| Low-Level Input Voltage (min; max is 0.3VCC / 0.2VCC) | VIL | -0.3 | V | VCC ≥ 2.5V and VCC < 2.5V | 4 | ||
| Low-Level Output Voltage | VOL | 0.4 | V | IOL = 2.1 mA, VCC ≥ 2.5V | 4 | ||
| Low-Level Output Voltage | VOL | 0.2 | V | IOL = 1.0 mA, VCC < 2.5V | 4 | ||
| Input Leakage Current | ILI | -1 | 1 | µA | CS = VCC, VIN = VSS or VCC | 4 | |
| Output Leakage Current | ILO | -1 | 1 | µA | CS = VCC, VOUT = VSS or VCC | 4 | |
| Pin Capacitance (all inputs and outputs) | CINT | 7 | pF | VCC = 3.6V (Note 2), TA = +25°C, f = 1 MHz | 4 | ||
| EEPROM read operating current | ICCEERD | 3 | mA | VCC = 3.6V, FCLK = 5 MHz, SO = Open | 4 | ||
| EEPROM write operating current | ICCEEWR | 5 | mA | VCC = 3.6V | 4 | ||
| SRAM/RTCC read operating current | ICCREAD | 3 | mA | VCC = 3.6V, FCLK = 5 MHz, SO = Open | 4 | ||
| SRAM/RTCC write operating current | ICCWRITE | 3 | mA | VCC = 3.6V, FCLK = 5 MHz | 4 | ||
| VCC Data Retention Current (oscillator off) | ICCDAT | 1 | µA | VCC = 3.6V | 4 | ||
| Timekeeping Current | ICCT | 1.2 | µA | VCC = 1.8V, CS = VCC, (Note 2) | 4 | ||
| Timekeeping Current | ICCT | 1.2 | 1.8 | µA | VCC = 3.0V, CS = VCC, (Note 2) | 4 | |
| Timekeeping Current | ICCT | 2.6 | µA | VCC = 3.6V, CS = VCC, (Note 2) | 4 | ||
| Power-Fail Switchover Voltage | VTRIP | 1.3 | 1.5 | 1.7 | V | 5 | |
| Backup Supply Voltage Range | VBAT | 1.3 | 3.6 | V | 5 | ||
| Timekeeping Backup Current | IBATT | 850 | nA | VBAT = 1.3V, VCC = VSS (Note 2) | 5 | ||
| Timekeeping Backup Current | IBATT | 1000 | 1200 | nA | VBAT = 3.0V, VCC = VSS (Note 2) | 5 | |
| Timekeeping Backup Current | IBATT | 2300 | nA | VBAT = 3.6V, VCC = VSS (Note 2) | 5 | ||
| VBAT Data Retention Current (oscillator off) | IBATDAT | 850 | nA | VBAT = 3.6V, VCC = VSS | 5 | ||
| Clock Frequency | FCLK | 5 | MHz | 2.5V ≤ Vcc < 3.6V | 6 | ||
| Clock Frequency | FCLK | 3 | MHz | 1.8V ≤ Vcc < 2.5V | 6 | ||
| CS Setup Time | TCSS | 100 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| CS Setup Time | TCSS | 150 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| CS Hold Time | TCSH | 100 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| CS Hold Time | TCSH | 150 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| Data Setup Time | TSU | 20 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| Data Setup Time | TSU | 30 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| Data Hold Time | THD | 40 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| Data Hold Time | THD | 50 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| Clock High Time | THI | 100 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| Clock High Time | THI | 150 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| Clock Low Time | TLO | 100 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| Clock Low Time | TLO | 150 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| Output Valid from Clock Low | TV | 100 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| Output Valid from Clock Low | TV | 160 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| Output Disable Time | TDIS | 80 | ns | 2.5V ≤ Vcc < 3.6V (Note 1) | 6 | ||
| Output Disable Time | TDIS | 160 | ns | 1.8V ≤ Vcc < 2.5V (Note 1) | 6 | ||
| Internal Write Cycle Time | TWC | 5 | ms | Note 2 | 6 | ||
| VCC Fall Time | TFVCC | 300 | µs | Note 1 | 6 | ||
| Oscillator Pin Capacitance (X1, X2 pins) | COSC | 3 | pF | Note 2 | 4 | ||
| Oscillator Frequency | FOSC | 32.768 | kHz | 6 |
CAD (KiCad official)
- Symbol:
MCP79520T-I - Footprint:
Package_SO:MSOP-10_3x3mm_P0.5mm - 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files:
mcp79520t-i-etched.step/mcp79520t-i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp79520t-i.step/mcp79520t-i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (58 pp, sha256
1caaeadd97693b59, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MCP79520T-I
**Microchip Tech** · Real-time Clocks (RTC) · MSOP-10
MCP79520T-I from Microchip Tech, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | X1 | input | Quartz crystal input for a 32.768 kHz crystal (optimized for 6-9 pF load), also the external clock input when configured for an external oscillator. |
| 2 | X2 | output | Quartz crystal output for the 32.768 kHz crystal; leave floating when using an external clock on X1. |
| 3 | VBAT | power_in | Battery backup supply input (1.3V to 3.6V) maintaining RTCC and SRAM when VCC is unavailable; connect to VSS if unused. |
| 4 | CS | input | Chip select input, active low selects the device and high deselects it, placing SO in high impedance. |
| 5 | VSS | power_in | Ground. |
| 6 | SI | input | Serial data input receiving instructions, addresses and data, latched on the rising edge of SCK. |
| 7 | SO | tri_state | Serial data output shifted out after the falling edge of SCK, high-impedance when CS is deselected. |
| 8 | SCK | input | Serial clock input synchronizing SPI communication, up to 5 MHz. |
| 9 | MFP | bidirectional | Multifunction pin shared by clock output and alarms; requires an external pull-up to VCC or VBAT and has a maximum sink current of 10 mA. |
| 10 | VCC | power_in | Primary power supply, operating range 1.8V to 3.6V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-10 |
| Category | RTC/Clock Chip |
| Pins | 10 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| All inputs and outputs w.r.t. VSS (lower limit; upper limit VCC+1.0V) | | -0.6 | | | V | -0.6V to VCC+1.0V | 4 |
| Storage temperature | | -65 | | 150 | °C | | 4 |
| Ambient temperature under bias | | -40 | | 85 | °C | | 4 |
| ESD protection on all pins | | | | 4 | kV | | 4 |
| Operating supply voltage | VCC | 1.8 | | 3.6 | V | Industrial (I) | 4 |
| Operating temperature | TA | -40 | | 85 | °C | Industrial (I) | 4 |
| Low-Level Input Voltage (min; max is 0.3VCC / 0.2VCC) | VIL | -0.3 | | | V | VCC ≥ 2.5V and VCC < 2.5V | 4 |
| Low-Level Output Voltage | VOL | | | 0.4 | V | IOL = 2.1 mA, VCC ≥ 2.5V | 4 |
| Low-Level Output Voltage | VOL | | | 0.2 | V | IOL = 1.0 mA, VCC < 2.5V | 4 |
| Input Leakage Current | ILI | -1 | | 1 | µA | CS = VCC, VIN = VSS or VCC | 4 |
| Output Leakage Current | ILO | -1 | | 1 | µA | CS = VCC, VOUT = VSS or VCC | 4 |
| Pin Capacitance (all inputs and outputs) | CINT | | | 7 | pF | VCC = 3.6V (Note 2), TA = +25°C, f = 1 MHz | 4 |
| EEPROM read operating current | ICCEERD | | | 3 | mA | VCC = 3.6V, FCLK = 5 MHz, SO = Open | 4 |
| EEPROM write operating current | ICCEEWR | | | 5 | mA | VCC = 3.6V | 4 |
| SRAM/RTCC read operating current | ICCREAD | | | 3 | mA | VCC = 3.6V, FCLK = 5 MHz, SO = Open | 4 |
| SRAM/RTCC write operating current | ICCWRITE | | | 3 | mA | VCC = 3.6V, FCLK = 5 MHz | 4 |
| VCC Data Retention Current (oscillator off) | ICCDAT | | | 1 | µA | VCC = 3.6V | 4 |
| Timekeeping Current | ICCT | | | 1.2 | µA | VCC = 1.8V, CS = VCC, (Note 2) | 4 |
| Timekeeping Current | ICCT | | 1.2 | 1.8 | µA | VCC = 3.0V, CS = VCC, (Note 2) | 4 |
| Timekeeping Current | ICCT | | | 2.6 | µA | VCC = 3.6V, CS = VCC, (Note 2) | 4 |
| Power-Fail Switchover Voltage | VTRIP | 1.3 | 1.5 | 1.7 | V | | 5 |
| Backup Supply Voltage Range | VBAT | 1.3 | | 3.6 | V | | 5 |
| Timekeeping Backup Current | IBATT | | | 850 | nA | VBAT = 1.3V, VCC = VSS (Note 2) | 5 |
| Timekeeping Backup Current | IBATT | | 1000 | 1200 | nA | VBAT = 3.0V, VCC = VSS (Note 2) | 5 |
| Timekeeping Backup Current | IBATT | | | 2300 | nA | VBAT = 3.6V, VCC = VSS (Note 2) | 5 |
| VBAT Data Retention Current (oscillator off) | IBATDAT | | | 850 | nA | VBAT = 3.6V, VCC = VSS | 5 |
| Clock Frequency | FCLK | | | 5 | MHz | 2.5V ≤ Vcc < 3.6V | 6 |
| Clock Frequency | FCLK | | | 3 | MHz | 1.8V ≤ Vcc < 2.5V | 6 |
| CS Setup Time | TCSS | 100 | | | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| CS Setup Time | TCSS | 150 | | | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| CS Hold Time | TCSH | 100 | | | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| CS Hold Time | TCSH | 150 | | | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| Data Setup Time | TSU | 20 | | | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| Data Setup Time | TSU | 30 | | | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| Data Hold Time | THD | 40 | | | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| Data Hold Time | THD | 50 | | | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| Clock High Time | THI | 100 | | | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| Clock High Time | THI | 150 | | | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| Clock Low Time | TLO | 100 | | | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| Clock Low Time | TLO | 150 | | | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| Output Valid from Clock Low | TV | | | 100 | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| Output Valid from Clock Low | TV | | | 160 | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| Output Disable Time | TDIS | | | 80 | ns | 2.5V ≤ Vcc < 3.6V (Note 1) | 6 |
| Output Disable Time | TDIS | | | 160 | ns | 1.8V ≤ Vcc < 2.5V (Note 1) | 6 |
| Internal Write Cycle Time | TWC | | | 5 | ms | Note 2 | 6 |
| VCC Fall Time | TFVCC | 300 | | | µs | Note 1 | 6 |
| Oscillator Pin Capacitance (X1, X2 pins) | COSC | | 3 | | pF | Note 2 | 4 |
| Oscillator Frequency | FOSC | | 32.768 | | kHz | | 6 |
## CAD (KiCad official)
- Symbol: `MCP79520T-I`
- Footprint: `Package_SO:MSOP-10_3x3mm_P0.5mm`
- 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files: `mcp79520t-i-etched.step` / `mcp79520t-i-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp79520t-i.step` / `mcp79520t-i.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/mcp79520t-i-datasheet.pdf) (58 pp, sha256 `1caaeadd97693b59`, retrieved 2026-10-31, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mcp79520t-i-datasheet.pdf)