main
Ray
Publish 0.1.0
a6a69a7
MCP73871-3CCI
Microchip Tech · Battery Management ICs · QFN-20(4x4)
MCP73871-3CCI from Microchip Tech, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | System output terminal that powers the system load while the battery charges independently; bypass to VSS with a minimum of 4.7 µF. |
| 2 | VPCC | input | Voltage proportional charge control input; supply 1.23V or greater to enable, or connect to IN to disable the feature. |
| 3 | SEL | input | Input type selection: low for USB port, high for AC-DC adapter. |
| 4 | PROG2 | input | USB port input current limit selection when SEL = Low (Low = 100 mA, High = 500 mA). |
| 5 | THERM | bidirectional | Thermistor monitoring input and bias current output for battery cell temperature monitoring. |
| 6 | PG | output | Open-drain power good status output, low when input is above the UVLO threshold and greater than the battery voltage. |
| 7 | STAT2 | output | Open-drain charge status output 2 for driving an LED or a host microcontroller. |
| 8 | STAT1/LBO | output | Open-drain charge status output 1; also low battery output indicator when VBAT > VIN. |
| 9 | TE | input | Timer enable; enables the safety timer when active-low. |
| 10 | VSS | power_in | Battery management 0V reference; connect to the negative terminal of the battery, system load and input supply. |
| 11 | VSS | power_in | Battery management 0V reference; connect to the negative terminal of the battery, system load and input supply. |
| 12 | PROG3 | bidirectional | Termination set point for both AC-DC adapter and USB port. |
| 13 | PROG1 | bidirectional | Fast charge current regulation setting with SEL = high via a resistor to VSS; also preconditioning set point for both USB port and AC-DC adapter. |
| 14 | VBAT | power_in | Battery positive input and output connection; bypass to VSS with a minimum of 4.7 µF. |
| 15 | VBAT | power_in | Battery positive input and output connection; bypass to VSS with a minimum of 4.7 µF. |
| 16 | VBAT_SENSE | bidirectional | Battery voltage sense; connect to the positive terminal of the battery, where the internal sense regulates the final voltage to VREG. |
| 17 | CE | input | Device charge enable; enabled when CE is high. |
| 18 | IN | power_in | Power supply input, recommended VREG + 0.3V to 6V; bypass to VSS with a minimum of 4.7 µF. |
| 19 | IN | power_in | Power supply input, recommended VREG + 0.3V to 6V; bypass to VSS with a minimum of 4.7 µF. |
| 20 | OUT | power_out | System output terminal that powers the system load while the battery charges independently; bypass to VSS with a minimum of 4.7 µF. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-20(4x4) |
| Category | Power Supply Chip |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | 7 | V | 4 | |||
| Storage temperature | -65 | 150 | °C | 4 | |||
| ESD HBM | 4 | kV | 1.5 k in series with 100 pF | 4 | |||
| ESD Machine Model | 300 | V | 200 pF, no series resistance | 4 | |||
| Supply Voltage | VIN | 6 | V | min is VREG + 0.3V | 4 | ||
| Supply Current, charging | ISS | 2500 | 3750 | µA | Charging | 4 | |
| Supply Current, charge complete | ISS | 260 | 350 | µA | Charge Complete | 4 | |
| Supply Current, standby | ISS | 180 | 300 | µA | Standby | 4 | |
| Supply Current, shutdown | ISS | 28 | 50 | µA | Shutdown (VDD < VBAT, 100 mV or VDD < VSTOP) | 4 | |
| Regulated Charge Voltage Tolerance | VRTOL | -0.5 | 0.5 | % | TA = +25°C | 4 | |
| Regulated Charge Voltage Tolerance | VRTOL | -0.75 | 0.75 | % | TA = -5°C to +55°C | 4 | |
| Line Regulation | /ΔVBAT/VBAT)/ΔVDD/ | 0.08 | 0.2 | %/V | VDD = [VREG(typical) + 1V] to 6V, IOUT = 10 mA | 4 | |
| Load Regulation | ΔVBAT/VBAT | 0.08 | 0.18 | % | IOUT = 10 mA to 150 mA, VDD = [VREG(typical) + 1V] | 4 | |
| AC-Adapter Fast Charge Current | IREG | 90 | 100 | 110 | mA | PROG1 = 10 k, TA = -5°C to +55°C, SEL = High | 5 |
| AC-Adapter Fast Charge Current | IREG | 900 | 1000 | 1100 | mA | PROG1 = 1 k, TA = -5°C to +55°C, SEL = High | 5 |
| USB Fast Charge Current | IREG | 80 | 90 | 100 | mA | PROG2 = Low, SEL = Low, (Note 2), TA = -5°C to +55°C | 5 |
| USB Fast Charge Current | IREG | 400 | 450 | 500 | mA | PROG2 = High, SEL = Low, (Note 2), TA = -5°C to +55°C | 5 |
| USB-Port Supply Current Limit | ILIMIT_USB | 80 | 90 | 100 | mA | PROG2 = Low, SEL = Low, TA = -5°C to +55°C | 5 |
| USB-Port Supply Current Limit | ILIMIT_USB | 400 | 450 | 500 | mA | PROG2 = High, SEL = Low, TA = -5°C to +55°C | 5 |
| AC-DC Adapter Current Limit | ILIMIT_AC | 1500 | 1650 | 1800 | mA | SEL = High, TA = -5°C to +55°C | 5 |
| VPCC Input Threshold Tolerance | VRTOL | -3 | 3 | % | 5 | ||
| VPCC Input Leakage Current | ILK | 0.01 | 1 | µA | VVPCC = VDD | 5 | |
| Precondition Current Ratio | IPREG/IREG | 7.5 | 10 | 12.5 | % | PROG1 = 1.0 k to 10 k, TA = -5°C to +55°C | 5 |
| Precondition Current Threshold Ratio | VPTH/VREG | 69 | 72 | 75 | % | VBAT Low-to-High | 5 |
| Charge Termination Current | ITERM | 75 | 100 | 125 | mA | PROG3 = 10 k, TA = -5°C to +55°C | 5 |
| Charge Termination Current | ITERM | 7.5 | 10 | 12.5 | mA | PROG3 = 100 k, TA = -5°C to +55°C | 5 |
| Output Reverse Leakage Current | IDISCHARGE | 30 | 40 | µA | Shutdown (VBAT < VDD < VUVLO) | 6 | |
| Output Reverse Leakage Current | IDISCHARGE | -6 | -13 | µA | Charge Complete | 6 | |
| Status Sink Current | ISINK | 16 | 35 | mA | 6 | ||
| Status Low Output Voltage | VOL | 0.4 | 1 | V | ISINK = 4 mA | 6 | |
| Status Input Leakage Current | ILK | 0.01 | 1 | µA | High Impedance, VDD on pin | 6 | |
| PROG1 Charge Impedance Range | RPROG | 1 | 20 | kΩ | 6 | ||
| PROG3 Termination Impedance Range | RPROG | 5 | 100 | kΩ | 6 | ||
| PROG2 Input High Voltage | VIH | 1.8 | V | 6 | |||
| PROG2 Input Low Voltage | VIL | 0.8 | V | 6 | |||
| TE Input High Voltage | VIH | 1.8 | V | Note 1 | 6 | ||
| TE Input Low Voltage | VIL | 0.8 | V | Note 1 | 6 | ||
| CE Input High Voltage | VIH | 1.8 | V | 7 | |||
| CE Input Low Voltage | VIL | 0.8 | V | 7 | |||
| SEL Input High Voltage | VIH | 1.8 | V | 7 | |||
| SEL Input Low Voltage | VIL | 0.8 | V | 7 | |||
| Thermistor Current Source | ITHERM | 47 | 50 | 53 | µA | 2 k < RTHERM < 50 k | 7 |
| Thermistor Upper Trip Threshold | VT1 | 1.2 | 1.24 | 1.26 | V | VT1 Low-to-High | 7 |
| Thermistor Lower Trip Threshold | VT2 | 0.23 | 0.25 | 0.27 | V | VT2 High-to-Low | 7 |
| UVLO Start Delay | tSTART | 5 | ms | VDD Low-to-High | 8 | ||
| Transition Time Out of Precondition | tDELAY | 10 | ms | VBAT < VPTH to VBAT > VPTH | 8 | ||
| Current Rise Time Out of Precondition | tRISE | 10 | ms | IOUT Rising to 90% of IREG | 8 | ||
| Precondition Comparator Filter Time | tPRECON | 0.4 | 1.3 | 3.2 | ms | Average VBAT Rise/Fall | 8 |
| Termination Comparator Filter Time | tTERM | 0.4 | 1.3 | 3.2 | ms | Average IOUT Falling | 8 |
| Charge Comparator Filter Time | tCHARGE | 0.4 | 1.3 | 3.2 | ms | Average VBAT Falling | 8 |
| Thermistor Comparator Filter Time | tTHERM | 0.4 | 1.3 | 3.2 | ms | Average THERM Rise/Fall | 8 |
| Status Output Turn-off | tOFF | 500 | µs | ISINK = 1 mA to 0 mA | 8 | ||
| Status Output Turn-on | tON | 500 | µs | ISINK = 0 mA to 1 mA | 8 | ||
| Specified Temperature Range | TA | -40 | 85 | °C | 8 | ||
| Operating Temperature Range | TJ | -40 | 125 | °C | 8 | ||
| Storage Temperature Range | TA | -65 | 150 | °C | 8 | ||
| Thermal Resistance, 20LD-QFN 4x4, junction to ambient | θJA | 50 | °C/W | 4-Layer JC51-7 Standard Board, Natural Convection | 8 | ||
| UVLO Hysteresis | VHYS | 90 | mV | 4 | |||
| Thermal Shutdown Die Temperature | TSD | 150 | °C | 7 |
CAD (KiCad official)
- Symbol:
MCP73871-3CCI - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
- 3D model files:
mcp73871-3cci-etched.step/mcp73871-3cci-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp73871-3cci.step/mcp73871-3cci.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (36 pp, sha256
56654f56a8ac83ad, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MCP73871-3CCI
**Microchip Tech** · Battery Management ICs · QFN-20(4x4)
MCP73871-3CCI from Microchip Tech, in a QFN-20(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | System output terminal that powers the system load while the battery charges independently; bypass to VSS with a minimum of 4.7 µF. |
| 2 | VPCC | input | Voltage proportional charge control input; supply 1.23V or greater to enable, or connect to IN to disable the feature. |
| 3 | SEL | input | Input type selection: low for USB port, high for AC-DC adapter. |
| 4 | PROG2 | input | USB port input current limit selection when SEL = Low (Low = 100 mA, High = 500 mA). |
| 5 | THERM | bidirectional | Thermistor monitoring input and bias current output for battery cell temperature monitoring. |
| 6 | PG | output | Open-drain power good status output, low when input is above the UVLO threshold and greater than the battery voltage. |
| 7 | STAT2 | output | Open-drain charge status output 2 for driving an LED or a host microcontroller. |
| 8 | STAT1/LBO | output | Open-drain charge status output 1; also low battery output indicator when VBAT > VIN. |
| 9 | TE | input | Timer enable; enables the safety timer when active-low. |
| 10 | VSS | power_in | Battery management 0V reference; connect to the negative terminal of the battery, system load and input supply. |
| 11 | VSS | power_in | Battery management 0V reference; connect to the negative terminal of the battery, system load and input supply. |
| 12 | PROG3 | bidirectional | Termination set point for both AC-DC adapter and USB port. |
| 13 | PROG1 | bidirectional | Fast charge current regulation setting with SEL = high via a resistor to VSS; also preconditioning set point for both USB port and AC-DC adapter. |
| 14 | VBAT | power_in | Battery positive input and output connection; bypass to VSS with a minimum of 4.7 µF. |
| 15 | VBAT | power_in | Battery positive input and output connection; bypass to VSS with a minimum of 4.7 µF. |
| 16 | VBAT_SENSE | bidirectional | Battery voltage sense; connect to the positive terminal of the battery, where the internal sense regulates the final voltage to VREG. |
| 17 | CE | input | Device charge enable; enabled when CE is high. |
| 18 | IN | power_in | Power supply input, recommended VREG + 0.3V to 6V; bypass to VSS with a minimum of 4.7 µF. |
| 19 | IN | power_in | Power supply input, recommended VREG + 0.3V to 6V; bypass to VSS with a minimum of 4.7 µF. |
| 20 | OUT | power_out | System output terminal that powers the system load while the battery charges independently; bypass to VSS with a minimum of 4.7 µF. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-20(4x4) |
| Category | Power Supply Chip |
| Pins | 21 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage | VIN | | | 7 | V | | 4 |
| Storage temperature | | -65 | | 150 | °C | | 4 |
| ESD HBM | | | | 4 | kV | 1.5 k in series with 100 pF | 4 |
| ESD Machine Model | | | | 300 | V | 200 pF, no series resistance | 4 |
| Supply Voltage | VIN | | | 6 | V | min is VREG + 0.3V | 4 |
| Supply Current, charging | ISS | | 2500 | 3750 | µA | Charging | 4 |
| Supply Current, charge complete | ISS | | 260 | 350 | µA | Charge Complete | 4 |
| Supply Current, standby | ISS | | 180 | 300 | µA | Standby | 4 |
| Supply Current, shutdown | ISS | | 28 | 50 | µA | Shutdown (VDD < VBAT, 100 mV or VDD < VSTOP) | 4 |
| Regulated Charge Voltage Tolerance | VRTOL | -0.5 | | 0.5 | % | TA = +25°C | 4 |
| Regulated Charge Voltage Tolerance | VRTOL | -0.75 | | 0.75 | % | TA = -5°C to +55°C | 4 |
| Line Regulation | /ΔVBAT/VBAT)/ΔVDD/ | | 0.08 | 0.2 | %/V | VDD = [VREG(typical) + 1V] to 6V, IOUT = 10 mA | 4 |
| Load Regulation | ΔVBAT/VBAT | | 0.08 | 0.18 | % | IOUT = 10 mA to 150 mA, VDD = [VREG(typical) + 1V] | 4 |
| AC-Adapter Fast Charge Current | IREG | 90 | 100 | 110 | mA | PROG1 = 10 k, TA = -5°C to +55°C, SEL = High | 5 |
| AC-Adapter Fast Charge Current | IREG | 900 | 1000 | 1100 | mA | PROG1 = 1 k, TA = -5°C to +55°C, SEL = High | 5 |
| USB Fast Charge Current | IREG | 80 | 90 | 100 | mA | PROG2 = Low, SEL = Low, (Note 2), TA = -5°C to +55°C | 5 |
| USB Fast Charge Current | IREG | 400 | 450 | 500 | mA | PROG2 = High, SEL = Low, (Note 2), TA = -5°C to +55°C | 5 |
| USB-Port Supply Current Limit | ILIMIT_USB | 80 | 90 | 100 | mA | PROG2 = Low, SEL = Low, TA = -5°C to +55°C | 5 |
| USB-Port Supply Current Limit | ILIMIT_USB | 400 | 450 | 500 | mA | PROG2 = High, SEL = Low, TA = -5°C to +55°C | 5 |
| AC-DC Adapter Current Limit | ILIMIT_AC | 1500 | 1650 | 1800 | mA | SEL = High, TA = -5°C to +55°C | 5 |
| VPCC Input Threshold Tolerance | VRTOL | -3 | | 3 | % | | 5 |
| VPCC Input Leakage Current | ILK | | 0.01 | 1 | µA | VVPCC = VDD | 5 |
| Precondition Current Ratio | IPREG/IREG | 7.5 | 10 | 12.5 | % | PROG1 = 1.0 k to 10 k, TA = -5°C to +55°C | 5 |
| Precondition Current Threshold Ratio | VPTH/VREG | 69 | 72 | 75 | % | VBAT Low-to-High | 5 |
| Charge Termination Current | ITERM | 75 | 100 | 125 | mA | PROG3 = 10 k, TA = -5°C to +55°C | 5 |
| Charge Termination Current | ITERM | 7.5 | 10 | 12.5 | mA | PROG3 = 100 k, TA = -5°C to +55°C | 5 |
| Output Reverse Leakage Current | IDISCHARGE | | 30 | 40 | µA | Shutdown (VBAT < VDD < VUVLO) | 6 |
| Output Reverse Leakage Current | IDISCHARGE | | -6 | -13 | µA | Charge Complete | 6 |
| Status Sink Current | ISINK | | 16 | 35 | mA | | 6 |
| Status Low Output Voltage | VOL | | 0.4 | 1 | V | ISINK = 4 mA | 6 |
| Status Input Leakage Current | ILK | | 0.01 | 1 | µA | High Impedance, VDD on pin | 6 |
| PROG1 Charge Impedance Range | RPROG | 1 | | 20 | kΩ | | 6 |
| PROG3 Termination Impedance Range | RPROG | 5 | | 100 | kΩ | | 6 |
| PROG2 Input High Voltage | VIH | 1.8 | | | V | | 6 |
| PROG2 Input Low Voltage | VIL | | | 0.8 | V | | 6 |
| TE Input High Voltage | VIH | 1.8 | | | V | Note 1 | 6 |
| TE Input Low Voltage | VIL | | | 0.8 | V | Note 1 | 6 |
| CE Input High Voltage | VIH | 1.8 | | | V | | 7 |
| CE Input Low Voltage | VIL | | | 0.8 | V | | 7 |
| SEL Input High Voltage | VIH | 1.8 | | | V | | 7 |
| SEL Input Low Voltage | VIL | | | 0.8 | V | | 7 |
| Thermistor Current Source | ITHERM | 47 | 50 | 53 | µA | 2 k < RTHERM < 50 k | 7 |
| Thermistor Upper Trip Threshold | VT1 | 1.2 | 1.24 | 1.26 | V | VT1 Low-to-High | 7 |
| Thermistor Lower Trip Threshold | VT2 | 0.23 | 0.25 | 0.27 | V | VT2 High-to-Low | 7 |
| UVLO Start Delay | tSTART | | | 5 | ms | VDD Low-to-High | 8 |
| Transition Time Out of Precondition | tDELAY | | | 10 | ms | VBAT < VPTH to VBAT > VPTH | 8 |
| Current Rise Time Out of Precondition | tRISE | | | 10 | ms | IOUT Rising to 90% of IREG | 8 |
| Precondition Comparator Filter Time | tPRECON | 0.4 | 1.3 | 3.2 | ms | Average VBAT Rise/Fall | 8 |
| Termination Comparator Filter Time | tTERM | 0.4 | 1.3 | 3.2 | ms | Average IOUT Falling | 8 |
| Charge Comparator Filter Time | tCHARGE | 0.4 | 1.3 | 3.2 | ms | Average VBAT Falling | 8 |
| Thermistor Comparator Filter Time | tTHERM | 0.4 | 1.3 | 3.2 | ms | Average THERM Rise/Fall | 8 |
| Status Output Turn-off | tOFF | | | 500 | µs | ISINK = 1 mA to 0 mA | 8 |
| Status Output Turn-on | tON | | | 500 | µs | ISINK = 0 mA to 1 mA | 8 |
| Specified Temperature Range | TA | -40 | | 85 | °C | | 8 |
| Operating Temperature Range | TJ | -40 | | 125 | °C | | 8 |
| Storage Temperature Range | TA | -65 | | 150 | °C | | 8 |
| Thermal Resistance, 20LD-QFN 4x4, junction to ambient | θJA | | 50 | | °C/W | 4-Layer JC51-7 Standard Board, Natural Convection | 8 |
| UVLO Hysteresis | VHYS | | 90 | | mV | | 4 |
| Thermal Shutdown Die Temperature | TSD | | 150 | | °C | | 7 |
## CAD (KiCad official)
- Symbol: `MCP73871-3CCI`
- Footprint: `Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm`
- 3D model: QFN-20(4x4) (KiCad packages3D, STEP)
- 3D model files: `mcp73871-3cci-etched.step` / `mcp73871-3cci-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp73871-3cci.step` / `mcp73871-3cci.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/mcp73871-3cci-datasheet.pdf) (36 pp, sha256 `56654f56a8ac83ad`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mcp73871-3cci-datasheet.pdf)