main
Ray Publish 0.1.0 22f7bb6

MCP6566UT-E

Microchip Tech · Comparators · SOT-23-5

MCP6566UT-E from Microchip Tech, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 VIN+ power_in Noninverting comparator input, a high-impedance CMOS input with low bias current and rail-to-rail operation from VSS - 0.3V to VDD + 0.3V.
2 VSS power_in Negative power supply, connected to ground in single-supply use, with VDD 1.8V to 5.5V above it.
3 VIN- power_in Inverting comparator input, a high-impedance CMOS input with low bias current and rail-to-rail operation from VSS - 0.3V to VDD + 0.3V.
4 OUT output Open-drain digital output that requires a pull-up resistor and supports pull-up voltages above and below VDD for level shifting and wired-OR.
5 VDD power_in Positive power supply, 1.8V to 5.5V above VSS, with a 0.01 µF to 0.1 µF local bypass capacitor within 2 mm of the pin.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOT-23-5
Category Operational Amplifier/Comparator
Pins 5

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VDD 1.8 5.5 V 3
Quiescent Current per Comparator IQ 60 100 130 µA IOUT = 0 3
Power Supply Rejection Ratio PSRR 63 70 dB VCM = VSS 3
Input Offset Voltage VOS -10 3 10 mV VCM = VSS (Note 1) 3
Input Bias Current IB 1500 5000 pA TA = +125°C, VIN- = VDD/2 3
Input Hysteresis Voltage VHYST 1 5 mV VCM = VSS (Notes 1, 2) 3
Common-Mode Input Voltage Range low/high at 1.8V VCMR -0.2 2 V VDD = 1.8V (VSS, 0.2 to VDD + 0.2) 3
Common-Mode Rejection Ratio CMRR 54 66 dB VCM = -0.3V to VDD + 0.3V, VDD = 5.5V 3
Common-Mode Rejection Ratio CMRR 50 63 dB VCM = VDD/2 to VDD + 0.3V, VDD = 5.5V 3
Common-Mode Rejection Ratio CMRR 54 65 dB VCM = -0.3V to VDD/2, VDD = 5.5V 3
Pull-up Voltage VPULL_UP 1.6 5.5 V 4
High-Level Output Current Leakage IOH_leak 1 µA Note 4 4
Low-Level Output Voltage VOL 0.6 V IOUT = 3 mA/8 mA @ VDD = 1.8V/5.5V 4
Propagation Delay High-to-Low, 100 mV Overdrive tPHL 56 80 ns VCM = VDD/2, VDD = 1.8V (Note 2) 4
Propagation Delay High-to-Low, 100 mV Overdrive tPHL 34 80 ns VCM = VDD/2, VDD = 5.5V 4
Specified Temperature Range TA -40 125 °C 4
Operating Temperature Range TA -40 125 °C 4
Storage Temperature Range TA -65 150 °C 4
Open-Drain Output 10.5 V VSS + 10.5V 3
Output Short-Circuit Current -25 25 mA 3
Current at Input Pins -2 2 mA 3
Current at Output and Supply Pins -50 50 mA 3
Storage Temperature -65 150 °C 3
Ambient Temperature with Power Applied -40 125 °C 3
Junction Temperature 150 °C 3
Thermal Resistance, 5-Lead SOT-23 θJA 201 °C/W 4
Input Offset Drift ΔVOS/ΔT 2 µV/°C VCM = VSS 3
Input Offset Current IOS 1 pA VCM = VSS 3
Input Bias Current IB 1 pA TA = +25°C, VIN- = VDD/2 3
Input Bias Current IB 60 pA TA = +85°C, VIN- = VDD/2 3
Input Hysteresis Linear Temp. Co. TC1 10 µV/°C 3
Input Hysteresis Quadratic Temp. Co. TC2 0.3 µV/°C2 3
Short-Circuit Current ISC 30 mA Not to exceed absolute max. rating (±30 typ) 4
Output Pin Capacitance COUT 8 pF 4
Fall Time tF 20 ns 4
Maximum Toggle Frequency fTG 4 MHz VDD = 5.5V 4
Maximum Toggle Frequency fTG 2 MHz VDD = 1.8V 4
Input Voltage Noise ENI 350 µVP-P 10 Hz to 10 MHz (Note 1) 4

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 36

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: MCP6566UT-E
  • Footprint: Package_TO_SOT_SMD:SOT-23-5
  • 3D model: SOT-23-5, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.45 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: mcp6566ut-e-ot-etched.step / mcp6566ut-e-ot-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp6566ut-e-ot.step / mcp6566ut-e-ot.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (50 pp, sha256 0bf95014310c37bc, retrieved 2026-11-16, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF