3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownMCP6547-I
Microchip Tech · Comparators · SOP-8
MCP6547-I from Microchip Tech, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUTA | output | Comparator A digital output is CMOS open-drain and can level-shift up to 10V using a pull-up resistor. |
| 2 | VINA- | input | Inverting input of comparator A is a high-impedance CMOS input with low bias current. |
| 3 | VINA+ | input | Non-inverting input of comparator A is a high-impedance CMOS input with low bias current and greater than rail-to-rail operation (VSS - 0.3V to VDD + 0.3V). |
| 4 | VSS | power_in | Negative power supply pin, 1.6V to 5.5V below VDD; typically connected to ground in single-supply use. |
| 5 | VINB+ | input | Non-inverting input of comparator B is a high-impedance CMOS input with low bias current. |
| 6 | VINB- | input | Inverting input of comparator B is a high-impedance CMOS input with low bias current. |
| 7 | OUTB | output | Comparator B digital output is CMOS open-drain and can level-shift up to 10V using a pull-up resistor. |
| 8 | VDD | power_in | Positive power supply pin, 1.6V to 5.5V above VSS, requiring a 0.01 µF to 0.1 µF bypass capacitor within 2 mm. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOP-8 |
| Category | Amplifiers/Comparators |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 1.6 | 5.5 | V | VPU ≥ VDD | 2 | |
| Quiescent Current (per comparator) | IQ | 0.3 | 0.6 | 1 | µA | IOUT = 0 | 2 |
| Common Mode Rejection Ratio | CMRR | 55 | 70 | dB | VDD = 5V, VCM = -0.3V to 5.3V | 2 | |
| Common Mode Rejection Ratio | CMRR | 50 | 65 | dB | VDD = 5V, VCM = 2.5V to 5.3V | 2 | |
| Power Supply Rejection Ratio | PSRR | 63 | 80 | dB | VCM = VSS | 2 | |
| Input Offset Voltage | VOS | -7 | 1.5 | 7 | mV | VCM = VSS (Note 1) | 2 |
| Input Hysteresis Voltage | VHYST | 1.5 | 3.3 | 6.5 | mV | VCM = VSS (Note 1) | 2 |
| At Temperature (I-Temp parts) Input Bias Current | IB | 25 | 100 | pA | TA = +85°C, VCM = VSS (Note 3) | 2 | |
| Open-Drain Output Pull-Up Voltage | VPU | 1.6 | 10 | V | (Note 4) | 3 | |
| High-Level Output Current | IOH | -100 | nA | VDD = 1.6V to 5.5V, VPU = 10V (Note 4) | 3 | ||
| Specified Temperature Range | TA | -40 | 85 | °C | 5 | ||
| Operating Temperature Range | TA | -40 | 125 | °C | Note | 5 | |
| Storage Temperature Range | TA | -65 | 150 | °C | 5 | ||
| VDD - VSS | VDD - VSS | 7 | V | 2 | |||
| Input current at input pins | -2 | 2 | mA | 2 | |||
| Current at output and supply pins | -30 | 30 | mA | 2 | |||
| Maximum Junction Temperature | TJ | 150 | °C | 2 | |||
| ESD Protection on All Pins (HBM) | 4 | kV | HBM; all parts other than MCP6546U | 2 | |||
| Drift with Temperature | ΔVOS/ΔTA | 3 | µV/°C | TA = -40°C to +125°C, VCM = VSS | 2 | ||
| Linear Temp. Co. | TC1 | 6.7 | µV/°C | TA = -40°C to +125°C, VCM = VSS (Note 2) | 2 | ||
| Quadratic Temp. Co. | TC2 | -0.035 | µV/°C2 | TA = -40°C to +125°C, VCM = VSS (Note 2) | 2 | ||
| Input Bias Current | IB | 1 | pA | VCM = VSS | 2 | ||
| Input Offset Current | IOS | 1 | pA | VCM = VSS | 2 | ||
| Short-Circuit Current | ISC | 1.5 | mA | VPU = VDD = 1.6V (Note 4) | 3 | ||
| Short-Circuit Current | ISC | 30 | mA | VPU = VDD = 5.5V (Note 4) | 3 | ||
| Output Pin Capacitance | COUT | 8 | pF | 3 | |||
| Fall Time | tF | 0.7 | µs | (Note 1) | 3 | ||
| Propagation Delay (High-to-Low) | tPHL | 4 | 8 | µs | 3 | ||
| Propagation Delay (Low-to-High) | tPLH | 3 | 8 | µs | (Note 1) | 3 | |
| Propagation Delay Skew | tPDS | -1 | µs | (Notes 1 and 2) | 3 | ||
| Maximum Toggle Frequency | fMAX | 225 | kHz | VDD = 1.6V | 3 | ||
| Maximum Toggle Frequency | fMAX | 165 | kHz | VDD = 5.5V | 3 | ||
| Input Noise Voltage | Eni | 200 | µVP-P | 10 Hz to 100 kHz | 3 | ||
| Thermal Resistance, 8L-SOIC | θJA | 149.5 | °C/W | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | P = Plastic DIP (300 mil Body), 8-lead, 14-lead SN = Plastic SOIC (150 mil Body), 8-lead | 41 |
CAD (KiCad official)
- Symbol:
MCP6547-I - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
mcp6547-i-etched.step/mcp6547-i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp6547-i.step/mcp6547-i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (44 pp, sha256
529fbd52c82b3fe8, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).