Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MCP3461-E

Microchip Tech · Analog To Digital Converters (ADCs) · TSSOP-20

MCP3461-E from Microchip Tech, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 AVDD power_in Analog supply voltage pin for the analog circuitry (2.7V to 3.6V), bypassed with typically 10 µF in parallel with 0.1 µF ceramic and monitored by the AVDD POR circuit.
2 AGND power_in Analog ground for internal analog circuitry, must be connected externally to the same ground as DGND (preferably star connection) as it is not connected internally to DGND.
3 REFIN- input Inverting differential reference input (VREF-), connected directly to AGND for single-ended reference applications, with 0.6V ≤ VREF ≤ AVDD.
4 REFIN+ input Noninverting differential reference input (VREF+), with 0.6V ≤ VREF ≤ AVDD and recommended 0.1 µF and 10 µF bypass capacitors to AGND.
5 CH0 input Analog input 0 to the input multiplexer, with absolute voltage range from AGND - 0.1V to VDD + 0.1V.
6 CH1 input Analog input 1 to the input multiplexer, with absolute voltage range from AGND - 0.1V to VDD + 0.1V.
7 NC unconnected Not connected.
8 NC unconnected Not connected.
9 NC unconnected Not connected.
10 NC unconnected Not connected.
11 NC unconnected Not connected.
12 NC unconnected Not connected.
13 CS input Schmitt-trigger SPI chip select input whose falling edge starts and rising edge ends a communication, with no communication possible when high.
14 SCK input Schmitt-trigger SPI serial clock input up to 20 MHz, data clocked in on rising edge and out on falling edge, compatible with SPI modes 0,0 and 1,1.
15 SDI input Schmitt-trigger SPI data input used to send the COMMAND byte after CS falling edge, followed by data words, clocked in on the rising edge of SCK.
16 SDO tri_state SPI data output clocked out on the falling edge of SCK, high-impedance when CS is high, during writes/Fast commands after the COMMAND byte, or when the device address does not match.
17 IRQ/MDAT output Interrupt output or modulator data output selected by IRQ_MODE[1], with inactive state high-Z (needs external pull-up to DVDD, typically 100-200 kΩ) or logic high selected by IRQ_MODE[0].
18 MCLK bidirectional Master clock input or AMCLK analog master clock output depending on CLK_SEL[1:0], with typical clock frequency of 4.9152 MHz.
19 DGND power_in Ground for internal digital circuitry, must be connected externally to the same ground as AGND, preferably with a star connection.
20 DVDD power_in Digital supply voltage pin (1.8V to 3.6V), bypassed with typically 10 µF in parallel with 0.1 µF ceramic and monitored by the DVDD POR circuit.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package TSSOP-20
Category Data Converters
Pins 20

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operating Voltage, Analog AVDD 2.7 3.6 V 6
Operating Voltage, Digital DVDD 1.8 V Max printed as AVDD + 0.1; DVDD ≤ 3.6V 6
Operating Current, Analog AIDD 0.56 0.81 mA BOOST[1:0] = 00, 0.5x 6
Operating Current, Analog AIDD 0.69 0.96 mA BOOST[1:0] = 01, 0.66x 6
Operating Current, Analog AIDD 0.93 1.3 mA BOOST[1:0] = 10, 1x 6
Operating Current, Analog AIDD 1.65 2.2 mA BOOST[1:0] = 11, 2x 6
Operating Current, Digital DIDD 0.25 0.37 mA Note 8 6
Analog Partial Shutdown Current AIDDS_PS 22 µA 6
Digital Partial Shutdown Current DIDDS_PS 158 µA 6
Analog Full Shutdown Current AIDDS_FS 0.83 µA CONFIG0 = 0x00, TA = +105°C, MCLK input in Idle mode (Note 2) 6
Analog Full Shutdown Current AIDDS_FS 1.1 µA CONFIG0 = 0x00, TA = +125°C, MCLK input in Idle mode 6
Digital Full Shutdown Current DIDDS_FS 2.4 µA CONFIG0 = 0x00, TA = +105°C, MCLK input in Idle mode (Note 2) 6
Digital Full Shutdown Current DIDDS_FS 5 µA CONFIG0 = 0x00, TA = +125°C, MCLK input in Idle mode 6
Reference Voltage Range (VREF+-VREF-) VREF 0.6 V Max printed as AVDD 7
Gain Error GE -3 3 % Note 6 7
No Missing Code Resolution Resolution 16 Bits Note 1 7
Gain Error Temperature Coefficient GE_DRIFT 0.5 2 ppm/oC GAIN: 1x, 2x, 4x (Note 2) 7
Gain Error Temperature Coefficient GE_DRIFT 1 4 ppm/oC GAIN: 8x (Note 2) 7
Gain Error Temperature Coefficient GE_DRIFT 2 8 ppm/oC GAIN: 0.33x, 16x (Note 2) 7
Integral Nonlinearity INL -10 10 ppm FSR GAIN = 0.33 (Note 2) 8
Integral Nonlinearity INL -7 7 ppm FSR GAIN = 1 (Note 2) 8
Integral Nonlinearity INL -20 20 ppm FSR GAIN = 8 (Note 2) 8
Integral Nonlinearity INL -32 32 ppm FSR GAIN = 16 (Note 2) 8
Signal-to-Noise and Distortion Ratio SINAD 96.9 97.2 dB AVDD = DVDD =VREF = 3.3V and TA = +25°C (Note 2) 8
Signal-to-Noise Ratio SNR 97 97.3 dBc AVDD = DVDD =VREF = 3.3V and TA = +25°C (Note 2) 8
Total Harmonic Distortion THD -116 -110 dB AVDD = DVDD =VREF = 3.3V and TA = +25°C. Includes the first 10 harmonics (Note 2) 8
Spurious-Free Dynamic Range SFDR 110 120 dBc AVDD = DVDD =VREF = 3.3V and TA = +25°C (Note 2) 8
Data Transfer Time to DR tDODR 50 ns 9
Modulator Output Valid from AMCLK High tDOMDAT 100 ns 2.7V ≤ DVDD ≤ 3.6V 9
Modulator Output Valid from AMCLK High tDOMDAT 200 ns 1.8V ≤ DVDD ≤ 2.7V 9
Master Clock Input Frequency Range fMCLK_EXT 1 20 MHz DVDD ≥ 2.7V 9
Master Clock Input Frequency Range fMCLK_EXT 1 10 MHz DVDD < 2.7V 9
Master Clock Input Duty Cycle fMCLK_DUTY 45 55 % 9
Internal Master Clock Frequency fMCLK_INT 3.3 6.6 MHz CLK_SEL[1] = 1 9
Data Ready Pulse High Time TDRH 16 DMCLK periods See Figure 5-15 9
Scan Mode Time Delay between sampling channels TDLY_SCAN 0 512 DMCLK periods 9
Scan Mode Time interval between scan cycles TTIMER_SCAN 0 1.67772e+07 DMCLK periods 9
Specified Temperature Range TA -40 125 °C 10
Operating Temperature Range TA -40 125 °C 10
Storage Temperature Range TA -65 150 °C 10
Serial Clock Frequency fSCK 20 MHz DVDD = 2.7V to 3.6V, CLOAD = 30 pF 10
Serial Clock Frequency fSCK 10 MHz DVDD = 1.8V to 2.7V, CLOAD = 30 pF 11
Input Leakage Current ILI_D 1 µA Pins configured as inputs or high-impedance outputs 11
DVDD, AVDD supply voltage DVDD, AVDD -0.3 4 V 5
Analog Inputs w.r.t. AGND -0.3 V Max printed as AVDD + 0.3V 5
Current at Input Pins -5 5 mA Printed ±5 mA 5
Current at Output and Supply Pins -20 20 mA Printed ±20 mA 5
Storage Temperature -65 150 °C 5
Ambient Temperature with Power Applied -65 125 °C 5
Soldering Temperature of Leads 300 °C 10 seconds 5
Maximum Junction Temperature TJ 150 °C 5
ESD on the Analog Inputs (HBM) 6 kV HBM 5
Thermal Resistance, 20-Lead TSSOP JA 44 °C/W 10
Power-on Reset Threshold Voltage, analog VPOR_A 1.75 V For analog circuits 6
Power-on Reset Threshold Voltage, digital VPOR_D 1.2 V For digital circuits 6
Hysteresis of Schmitt Trigger Inputs VHYS 200 mV 11

CAD (KiCad official)

  • Symbol: MCP3461-E
  • Footprint: Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm
  • 3D model: TSSOP-20 (KiCad packages3D, STEP)
  • 3D model files: mcp3461-e-etched.step / mcp3461-e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp3461-e.step / mcp3461-e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (108 pp, sha256 c83ec3033af8ff79, retrieved 2026-10-26, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF