main
Ray
Publish 0.1.0
a106bb8
MCP25625T-E
Microchip Tech · CAN Transceivers · SSOP-28-208mil
MCP25625T-E from Microchip Tech, in a SSOP-28-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIO | power_in | Digital I/O supply pin for the CAN transceiver; undervoltage threshold is typically 1.2V and the transceiver transfers data to RXD down to 1V on VIO. |
| 2 | NC | unconnected | No connection. |
| 3 | CANL | bidirectional | CAN low-level voltage I/O that drives the low side of the differential bus, is tied to the receive comparator, and disconnects from the bus when VDDA is not powered. |
| 4 | CANH | bidirectional | CAN high-level voltage I/O that drives the high side of the differential bus, is tied to the receive comparator, and disconnects from the bus when VDDA is not powered. |
| 5 | STBY | input | Standby mode input selecting Normal or Standby mode of the CAN transceiver, with an internal MOS pull-up to VIO (typically 660 kΩ at 5V). |
| 6 | Tx1RTS | input | TXB1 request-to-send input, configurable as a general purpose input. |
| 7 | Tx2RTS | input | TXB2 request-to-send input, configurable as a general purpose input. |
| 8 | OSC2 | output | External oscillator output for the crystal or ceramic resonator; left open when OSC1 is driven by an external clock. |
| 9 | OSC1 | input | External oscillator input for a parallel cut crystal/ceramic resonator or an external clock source. |
| 10 | GND | power_in | Ground for the CAN controller. |
| 11 | Rx1BF | output | RxB1 interrupt output, configurable as a digital output via BFPCTRL; high-impedance when its pin function is disabled. |
| 12 | Rx0BF | output | RxB0 interrupt output, configurable as a digital output via BFPCTRL; high-impedance when its pin function is disabled. |
| 13 | INT | output | Interrupt output to the microcontroller; interrupts must be cleared through SPI. |
| 14 | SCK | input | SPI clock input, up to 10 MHz, supporting SPI modes 0,0 and 1,1. |
| 15 | SI | input | SPI data input. |
| 16 | SO | output | SPI data output. |
| 17 | CS | input | SPI chip select input. |
| 18 | RESET | input | Active-low hardware reset input, which can optionally be pulled up to VDD with a 10 kΩ resistor; must be held low at least 2 µs (tRL) after VDD reaches operating voltage. |
| 19 | VDD | power_in | Power supply for the CAN controller, 2.7V to 5.5V. |
| 20 | TxCAN | output | Transmit output from the CAN controller to the CAN transceiver, to be connected externally to TXD. |
| 21 | RXCAN | input | Receive input to the CAN controller from the CAN transceiver, to be connected externally to RXD. |
| 22 | CLKOUT | output | Clock output/SOF with prescaler of 1, 2, 4 or 8 (default divide-by-8), high-impedance when disabled, maximum 25 MHz. |
| 23 | Tx0RTS | input | TXB0 request-to-send input, configurable as a general purpose input. |
| 24 | TXD | input | Transmit data input of the CAN transceiver from the CAN controller, with an internal pull-up (nominal 33 kΩ) to VIO; low is Dominant, high is Recessive. |
| 25 | NC | unconnected | No connection. |
| 26 | VSS | power_in | Ground supply pin of the CAN transceiver. |
| 27 | VDDA | power_in | Positive supply for the CAN transceiver (transmitter and receiver, including wake-up receiver), 4.5V to 5.5V. |
| 28 | RXD | output | CMOS receive data output of the CAN transceiver to the CAN controller, supplied by VIO; high when bus is Recessive and low when Dominant. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SSOP-28-208mil |
| Category | Interface |
| Pins | 28 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (controller) | VDD | 2.7 | 5.5 | V | TAMB = -40°C to +125°C | 68 | |
| Register Retention Voltage | VRET | 2.4 | V | 68 | |||
| High-Level Input Voltage RxCAN | VIH | 2 | V | RxCAN; max printed as VDD +1 | 68 | ||
| High-Level Input Voltage SCK, CS, SI, TxnRTS | VIH | 0.7 | VDD | SCK, CS, SI, TxnRTS pins; min 0.7 VDD, max printed as VDD +1 V | 68 | ||
| High-Level Input Voltage OSC1 | VIH | 0.85 | 1 | VDD | OSC1; min 0.85 VDD, max VDD | 68 | |
| High-Level Input Voltage RESET | VIH | 0.85 | 1 | VDD | RESET; min 0.85 VDD, max VDD | 68 | |
| Low-Level Input Voltage RxCAN, TxnRTS | VIL | 0.15 | VDD | RxCAN, TxnRTS pins; min printed as -0.3 V, max 0.15 VDD | 68 | ||
| Low-Level Input Voltage SCK, CS, SI | VIL | 0.4 | VDD | SCK, CS, SI; min printed as -0.3 V, max 0.4 VDD | 68 | ||
| Low-Level Input Voltage OSC1 | VIL | 0.3 | VDD | OSC1; min VSS, max 0.3 VDD | 68 | ||
| Low-Level Input Voltage RESET | VIL | 0.15 | VDD | RESET; min VSS, max 0.15 VDD | 68 | ||
| Low-Level Output Voltage TxCAN | VOL | 0.6 | V | IOL = +6.0 mA, VDD = 4.5V | 68 | ||
| Low-Level Output Voltage RxnBF Pins | VOL | 0.6 | V | IOL = +8.5 mA, VDD = 4.5V | 68 | ||
| High-Level Output Voltage TxCAN, RxnBF Pins | VOH | 0.7 | V | VDD, 0.7 V minimum; IOH = -3.0 mA, VDD = 4.5V | 68 | ||
| High-Level Output Voltage SO, CLKOUT | VOH | 0.5 | V | VDD, 0.5 V minimum; IOH = -400 µA, VDD = 4.5V | 68 | ||
| Input Leakage Current, all I/Os except OSC1 and TxnRTS | ILI | -1 | 1 | µA | CS = RESET = VDD, VIN = VSS to VDD | 68 | |
| Internal Capacitance (all inputs and outputs) | CINT | 7 | pF | TAMB = +25°C, fC = 1.0 MHz, VDD = 0V (Note 1) | 68 | ||
| Operating Current | IDD | 10 | mA | VDD = 5.5V, FOSC = 25 MHz, FCLK = 1 MHz, SO = Open | 68 | ||
| Standby Current (Sleep mode) | IDDS | 8 | µA | CS, TxnRTS = VDD, Inputs tied to VDD or VSS, -40°C to +125°C | 68 | ||
| Clock In Frequency | FOSC | 1 | 25 | MHz | 68 | ||
| SPI Clock Frequency | FCLK | 10 | MHz | 70 | |||
| RESET Pin Low Time | tRL | 2 | µs | 69 | |||
| Wake-up Noise Filter | tWF | 100 | ns | 69 | |||
| VDDA Pin Voltage Range | VDDA | 4.5 | 5.5 | V | 71 | ||
| Supply Current, Recessive | IDD | 5 | 10 | mA | Recessive; VTXD = VDDA | 71 | |
| Supply Current, Dominant | IDD | 45 | 70 | mA | Dominant; VTXD = 0V | 71 | |
| Standby Current (VDDA) | IDDS | 5 | 15 | µA | Includes IIO | 71 | |
| High Level of the POR Comparator | VPORH | 3.8 | 4.3 | V | 71 | ||
| Low Level of the POR Comparator | VPORL | 3.4 | 4 | V | 71 | ||
| Digital Supply Voltage Range | VIO | 2.7 | 5.5 | V | 71 | ||
| Supply Current on VIO, Recessive | IIO | 4 | 30 | µA | Recessive; VTXD = VIO | 71 | |
| Supply Current on VIO, Dominant | IIO | 85 | 500 | µA | Dominant; VTXD = 0V | 71 | |
| Standby Current (VIO) | IDDS | 0.3 | 1 | µA | (Note 1) | 71 | |
| CANH, CANL Recessive Bus Output Voltage | VO(R) | 2 | 3 | V | VTXD = VDDA; No load; typ printed as 0.5 VDDA | 71 | |
| CANH, CANL Bus Output Voltage in Standby | VO(S) | -0.1 | 0 | 0.1 | V | STBY = VTXD = VDDA; No load | 71 |
| Recessive Output Current | IO(R) | -5 | 5 | mA | -24V < VCAN < +24V | 71 | |
| CANH Dominant Output Voltage | VO(D) | 2.75 | 3.5 | 4.5 | V | TXD = 0; RL = 50 to 65 | 71 |
| CANL Dominant Output Voltage | VO(D) | 0.5 | 1.5 | 2.25 | V | RL = 50 to 65 | 71 |
| Dominant Differential Output Voltage | VO(DIFF) | 1.5 | 2 | 3 | V | VTXD = VSS; RL = 50 to 65; Figure 7-2, Figure 7-4 | 71 |
| Recessive Differential Input Voltage, Normal mode | VDIFF(R)(I) | -1 | 0.5 | V | Normal mode; -12V < V(CANH, CANL) < +12V; see Figure 7-6 (Note 2) | 72 | |
| Dominant Differential Input Voltage, Normal mode | VDIFF(D)(I) | 0.9 | V | Normal mode; -12V < V(CANH, CANL) < +12V; see Figure 7-6 (Note 2); max printed as VDDA | 72 | ||
| Differential Receiver Threshold, Normal mode | VTH(DIFF) | 0.5 | 0.7 | 0.9 | V | Normal mode; -12V < V(CANH, CANL) < +12V; see Figure 7-6 (Note 2) | 72 |
| Common-Mode Input Resistance | RIN | 10 | 30 | kΩ | (Note 1) | 72 | |
| Differential Input Resistance | RIN(DIFF) | 10 | 100 | kΩ | (Note 1) | 72 | |
| High-Level Input Voltage (TXD, STBY) | VIH | 0.7 | V | min 0.7 VIO, max printed as VIO + 0.3 V | 72 | ||
| Low-Level Input Voltage (TXD, STBY) | VIL | -0.3 | V | max printed as 0.3 VIO | 72 | ||
| RXD High-Level Output Voltage | VOH | 0.4 | V | VIO, 0.4 V minimum; IOH = -1 mA; typical -2 mA | 72 | ||
| RXD Low-Level Output Voltage | VOL | 0.4 | V | IOL = 4 mA; typical 8 mA | 72 | ||
| Shutdown Junction Temperature | TJ(SD) | 165 | 175 | 185 | °C | -12V < V(CANH, CANL) < +12V (Note 1) | 72 |
| Shutdown Temperature Hysteresis | TJ(HYST) | 20 | 30 | °C | -12V < V(CANH, CANL) < +12V (Note 1) | 72 | |
| Propagation Delay TXD to RXD, negative edge | tTXD-RXD | 125 | ns | Negative edge on TXD | 73 | ||
| Propagation Delay TXD to RXD, positive edge | tTXD-RXD | 235 | ns | Positive edge on TXD | 73 | ||
| Delay Standby to Normal mode | tWAKE | 5 | 25 | 40 | µs | Negative edge on STBY | 73 |
| Supply Voltage VDD | VDD | 7 | V | 67 | |||
| Supply Voltage VDDA | VDDA | 7 | V | 67 | |||
| Supply Voltage VIO | VIO | 7 | V | 67 | |||
| DC Voltage at CANH, CANL | -58 | 58 | V | 67 | |||
| Storage temperature | -55 | 150 | °C | 67 | |||
| Operating Ambient Temperature | TA | -40 | 125 | °C | 67 | ||
| Virtual Junction Temperature | TVJ | -40 | 150 | °C | IEC60747-1 | 67 | |
| Thermal Resistance, 28L-SSOP | θJA | 80 | °C/W | 77 |
CAD (KiCad official)
- Symbol:
MCP25625T-E - Footprint:
Package_SO:SSOP-28_5.3x10.2mm_P0.65mm - 3D model: SSOP-28-208mil (KiCad packages3D, STEP)
- 3D model files:
mcp25625t-e-ss-etched.step/mcp25625t-e-ss-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp25625t-e-ss.step/mcp25625t-e-ss.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (90 pp, sha256
e4fba63531389fbf, retrieved 2026-11-16, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MCP25625T-E
**Microchip Tech** · CAN Transceivers · SSOP-28-208mil
MCP25625T-E from Microchip Tech, in a SSOP-28-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIO | power_in | Digital I/O supply pin for the CAN transceiver; undervoltage threshold is typically 1.2V and the transceiver transfers data to RXD down to 1V on VIO. |
| 2 | NC | unconnected | No connection. |
| 3 | CANL | bidirectional | CAN low-level voltage I/O that drives the low side of the differential bus, is tied to the receive comparator, and disconnects from the bus when VDDA is not powered. |
| 4 | CANH | bidirectional | CAN high-level voltage I/O that drives the high side of the differential bus, is tied to the receive comparator, and disconnects from the bus when VDDA is not powered. |
| 5 | STBY | input | Standby mode input selecting Normal or Standby mode of the CAN transceiver, with an internal MOS pull-up to VIO (typically 660 kΩ at 5V). |
| 6 | Tx1RTS | input | TXB1 request-to-send input, configurable as a general purpose input. |
| 7 | Tx2RTS | input | TXB2 request-to-send input, configurable as a general purpose input. |
| 8 | OSC2 | output | External oscillator output for the crystal or ceramic resonator; left open when OSC1 is driven by an external clock. |
| 9 | OSC1 | input | External oscillator input for a parallel cut crystal/ceramic resonator or an external clock source. |
| 10 | GND | power_in | Ground for the CAN controller. |
| 11 | Rx1BF | output | RxB1 interrupt output, configurable as a digital output via BFPCTRL; high-impedance when its pin function is disabled. |
| 12 | Rx0BF | output | RxB0 interrupt output, configurable as a digital output via BFPCTRL; high-impedance when its pin function is disabled. |
| 13 | INT | output | Interrupt output to the microcontroller; interrupts must be cleared through SPI. |
| 14 | SCK | input | SPI clock input, up to 10 MHz, supporting SPI modes 0,0 and 1,1. |
| 15 | SI | input | SPI data input. |
| 16 | SO | output | SPI data output. |
| 17 | CS | input | SPI chip select input. |
| 18 | RESET | input | Active-low hardware reset input, which can optionally be pulled up to VDD with a 10 kΩ resistor; must be held low at least 2 µs (tRL) after VDD reaches operating voltage. |
| 19 | VDD | power_in | Power supply for the CAN controller, 2.7V to 5.5V. |
| 20 | TxCAN | output | Transmit output from the CAN controller to the CAN transceiver, to be connected externally to TXD. |
| 21 | RXCAN | input | Receive input to the CAN controller from the CAN transceiver, to be connected externally to RXD. |
| 22 | CLKOUT | output | Clock output/SOF with prescaler of 1, 2, 4 or 8 (default divide-by-8), high-impedance when disabled, maximum 25 MHz. |
| 23 | Tx0RTS | input | TXB0 request-to-send input, configurable as a general purpose input. |
| 24 | TXD | input | Transmit data input of the CAN transceiver from the CAN controller, with an internal pull-up (nominal 33 kΩ) to VIO; low is Dominant, high is Recessive. |
| 25 | NC | unconnected | No connection. |
| 26 | VSS | power_in | Ground supply pin of the CAN transceiver. |
| 27 | VDDA | power_in | Positive supply for the CAN transceiver (transmitter and receiver, including wake-up receiver), 4.5V to 5.5V. |
| 28 | RXD | output | CMOS receive data output of the CAN transceiver to the CAN controller, supplied by VIO; high when bus is Recessive and low when Dominant. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SSOP-28-208mil |
| Category | Interface |
| Pins | 28 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (controller) | VDD | 2.7 | | 5.5 | V | TAMB = -40°C to +125°C | 68 |
| Register Retention Voltage | VRET | 2.4 | | | V | | 68 |
| High-Level Input Voltage RxCAN | VIH | 2 | | | V | RxCAN; max printed as VDD +1 | 68 |
| High-Level Input Voltage SCK, CS, SI, TxnRTS | VIH | 0.7 | | | VDD | SCK, CS, SI, TxnRTS pins; min 0.7 VDD, max printed as VDD +1 V | 68 |
| High-Level Input Voltage OSC1 | VIH | 0.85 | | 1 | VDD | OSC1; min 0.85 VDD, max VDD | 68 |
| High-Level Input Voltage RESET | VIH | 0.85 | | 1 | VDD | RESET; min 0.85 VDD, max VDD | 68 |
| Low-Level Input Voltage RxCAN, TxnRTS | VIL | | | 0.15 | VDD | RxCAN, TxnRTS pins; min printed as -0.3 V, max 0.15 VDD | 68 |
| Low-Level Input Voltage SCK, CS, SI | VIL | | | 0.4 | VDD | SCK, CS, SI; min printed as -0.3 V, max 0.4 VDD | 68 |
| Low-Level Input Voltage OSC1 | VIL | | | 0.3 | VDD | OSC1; min VSS, max 0.3 VDD | 68 |
| Low-Level Input Voltage RESET | VIL | | | 0.15 | VDD | RESET; min VSS, max 0.15 VDD | 68 |
| Low-Level Output Voltage TxCAN | VOL | | | 0.6 | V | IOL = +6.0 mA, VDD = 4.5V | 68 |
| Low-Level Output Voltage RxnBF Pins | VOL | | | 0.6 | V | IOL = +8.5 mA, VDD = 4.5V | 68 |
| High-Level Output Voltage TxCAN, RxnBF Pins | VOH | 0.7 | | | V | VDD, 0.7 V minimum; IOH = -3.0 mA, VDD = 4.5V | 68 |
| High-Level Output Voltage SO, CLKOUT | VOH | 0.5 | | | V | VDD, 0.5 V minimum; IOH = -400 µA, VDD = 4.5V | 68 |
| Input Leakage Current, all I/Os except OSC1 and TxnRTS | ILI | -1 | | 1 | µA | CS = RESET = VDD, VIN = VSS to VDD | 68 |
| Internal Capacitance (all inputs and outputs) | CINT | | | 7 | pF | TAMB = +25°C, fC = 1.0 MHz, VDD = 0V (Note 1) | 68 |
| Operating Current | IDD | | | 10 | mA | VDD = 5.5V, FOSC = 25 MHz, FCLK = 1 MHz, SO = Open | 68 |
| Standby Current (Sleep mode) | IDDS | | | 8 | µA | CS, TxnRTS = VDD, Inputs tied to VDD or VSS, -40°C to +125°C | 68 |
| Clock In Frequency | FOSC | 1 | | 25 | MHz | | 68 |
| SPI Clock Frequency | FCLK | | | 10 | MHz | | 70 |
| RESET Pin Low Time | tRL | 2 | | | µs | | 69 |
| Wake-up Noise Filter | tWF | 100 | | | ns | | 69 |
| VDDA Pin Voltage Range | VDDA | 4.5 | | 5.5 | V | | 71 |
| Supply Current, Recessive | IDD | | 5 | 10 | mA | Recessive; VTXD = VDDA | 71 |
| Supply Current, Dominant | IDD | | 45 | 70 | mA | Dominant; VTXD = 0V | 71 |
| Standby Current (VDDA) | IDDS | | 5 | 15 | µA | Includes IIO | 71 |
| High Level of the POR Comparator | VPORH | 3.8 | | 4.3 | V | | 71 |
| Low Level of the POR Comparator | VPORL | 3.4 | | 4 | V | | 71 |
| Digital Supply Voltage Range | VIO | 2.7 | | 5.5 | V | | 71 |
| Supply Current on VIO, Recessive | IIO | | 4 | 30 | µA | Recessive; VTXD = VIO | 71 |
| Supply Current on VIO, Dominant | IIO | | 85 | 500 | µA | Dominant; VTXD = 0V | 71 |
| Standby Current (VIO) | IDDS | | 0.3 | 1 | µA | (Note 1) | 71 |
| CANH, CANL Recessive Bus Output Voltage | VO(R) | 2 | | 3 | V | VTXD = VDDA; No load; typ printed as 0.5 VDDA | 71 |
| CANH, CANL Bus Output Voltage in Standby | VO(S) | -0.1 | 0 | 0.1 | V | STBY = VTXD = VDDA; No load | 71 |
| Recessive Output Current | IO(R) | -5 | | 5 | mA | -24V < VCAN < +24V | 71 |
| CANH Dominant Output Voltage | VO(D) | 2.75 | 3.5 | 4.5 | V | TXD = 0; RL = 50 to 65 | 71 |
| CANL Dominant Output Voltage | VO(D) | 0.5 | 1.5 | 2.25 | V | RL = 50 to 65 | 71 |
| Dominant Differential Output Voltage | VO(DIFF) | 1.5 | 2 | 3 | V | VTXD = VSS; RL = 50 to 65; Figure 7-2, Figure 7-4 | 71 |
| Recessive Differential Input Voltage, Normal mode | VDIFF(R)(I) | -1 | | 0.5 | V | Normal mode; -12V < V(CANH, CANL) < +12V; see Figure 7-6 (Note 2) | 72 |
| Dominant Differential Input Voltage, Normal mode | VDIFF(D)(I) | 0.9 | | | V | Normal mode; -12V < V(CANH, CANL) < +12V; see Figure 7-6 (Note 2); max printed as VDDA | 72 |
| Differential Receiver Threshold, Normal mode | VTH(DIFF) | 0.5 | 0.7 | 0.9 | V | Normal mode; -12V < V(CANH, CANL) < +12V; see Figure 7-6 (Note 2) | 72 |
| Common-Mode Input Resistance | RIN | 10 | | 30 | kΩ | (Note 1) | 72 |
| Differential Input Resistance | RIN(DIFF) | 10 | | 100 | kΩ | (Note 1) | 72 |
| High-Level Input Voltage (TXD, STBY) | VIH | 0.7 | | | V | min 0.7 VIO, max printed as VIO + 0.3 V | 72 |
| Low-Level Input Voltage (TXD, STBY) | VIL | -0.3 | | | V | max printed as 0.3 VIO | 72 |
| RXD High-Level Output Voltage | VOH | 0.4 | | | V | VIO, 0.4 V minimum; IOH = -1 mA; typical -2 mA | 72 |
| RXD Low-Level Output Voltage | VOL | | | 0.4 | V | IOL = 4 mA; typical 8 mA | 72 |
| Shutdown Junction Temperature | TJ(SD) | 165 | 175 | 185 | °C | -12V < V(CANH, CANL) < +12V (Note 1) | 72 |
| Shutdown Temperature Hysteresis | TJ(HYST) | 20 | | 30 | °C | -12V < V(CANH, CANL) < +12V (Note 1) | 72 |
| Propagation Delay TXD to RXD, negative edge | tTXD-RXD | | | 125 | ns | Negative edge on TXD | 73 |
| Propagation Delay TXD to RXD, positive edge | tTXD-RXD | | | 235 | ns | Positive edge on TXD | 73 |
| Delay Standby to Normal mode | tWAKE | 5 | 25 | 40 | µs | Negative edge on STBY | 73 |
| Supply Voltage VDD | VDD | | | 7 | V | | 67 |
| Supply Voltage VDDA | VDDA | | | 7 | V | | 67 |
| Supply Voltage VIO | VIO | | | 7 | V | | 67 |
| DC Voltage at CANH, CANL | | -58 | | 58 | V | | 67 |
| Storage temperature | | -55 | | 150 | °C | | 67 |
| Operating Ambient Temperature | TA | -40 | | 125 | °C | | 67 |
| Virtual Junction Temperature | TVJ | -40 | | 150 | °C | IEC60747-1 | 67 |
| Thermal Resistance, 28L-SSOP | θJA | | 80 | | °C/W | | 77 |
## CAD (KiCad official)
- Symbol: `MCP25625T-E`
- Footprint: `Package_SO:SSOP-28_5.3x10.2mm_P0.65mm`
- 3D model: SSOP-28-208mil (KiCad packages3D, STEP)
- 3D model files: `mcp25625t-e-ss-etched.step` / `mcp25625t-e-ss-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp25625t-e-ss.step` / `mcp25625t-e-ss.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](https://ww1.microchip.com/downloads/en/DeviceDoc/MCP25625-CAN-Controller-Data-Sheet-20005282C.pdf) (90 pp, sha256 `e4fba63531389fbf`, retrieved 2026-11-16, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mcp25625t-e-ss-datasheet.pdf)