Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MCP25625T-E

Microchip Tech · CAN Transceivers · SSOP-28-208mil

MCP25625T-E from Microchip Tech, in a SSOP-28-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIO power_in Digital I/O supply pin for the CAN transceiver; undervoltage threshold is typically 1.2V and the transceiver transfers data to RXD down to 1V on VIO.
2 NC unconnected No connection.
3 CANL bidirectional CAN low-level voltage I/O that drives the low side of the differential bus, is tied to the receive comparator, and disconnects from the bus when VDDA is not powered.
4 CANH bidirectional CAN high-level voltage I/O that drives the high side of the differential bus, is tied to the receive comparator, and disconnects from the bus when VDDA is not powered.
5 STBY input Standby mode input selecting Normal or Standby mode of the CAN transceiver, with an internal MOS pull-up to VIO (typically 660 kΩ at 5V).
6 Tx1RTS input TXB1 request-to-send input, configurable as a general purpose input.
7 Tx2RTS input TXB2 request-to-send input, configurable as a general purpose input.
8 OSC2 output External oscillator output for the crystal or ceramic resonator; left open when OSC1 is driven by an external clock.
9 OSC1 input External oscillator input for a parallel cut crystal/ceramic resonator or an external clock source.
10 GND power_in Ground for the CAN controller.
11 Rx1BF output RxB1 interrupt output, configurable as a digital output via BFPCTRL; high-impedance when its pin function is disabled.
12 Rx0BF output RxB0 interrupt output, configurable as a digital output via BFPCTRL; high-impedance when its pin function is disabled.
13 INT output Interrupt output to the microcontroller; interrupts must be cleared through SPI.
14 SCK input SPI clock input, up to 10 MHz, supporting SPI modes 0,0 and 1,1.
15 SI input SPI data input.
16 SO output SPI data output.
17 CS input SPI chip select input.
18 RESET input Active-low hardware reset input, which can optionally be pulled up to VDD with a 10 kΩ resistor; must be held low at least 2 µs (tRL) after VDD reaches operating voltage.
19 VDD power_in Power supply for the CAN controller, 2.7V to 5.5V.
20 TxCAN output Transmit output from the CAN controller to the CAN transceiver, to be connected externally to TXD.
21 RXCAN input Receive input to the CAN controller from the CAN transceiver, to be connected externally to RXD.
22 CLKOUT output Clock output/SOF with prescaler of 1, 2, 4 or 8 (default divide-by-8), high-impedance when disabled, maximum 25 MHz.
23 Tx0RTS input TXB0 request-to-send input, configurable as a general purpose input.
24 TXD input Transmit data input of the CAN transceiver from the CAN controller, with an internal pull-up (nominal 33 kΩ) to VIO; low is Dominant, high is Recessive.
25 NC unconnected No connection.
26 VSS power_in Ground supply pin of the CAN transceiver.
27 VDDA power_in Positive supply for the CAN transceiver (transmitter and receiver, including wake-up receiver), 4.5V to 5.5V.
28 RXD output CMOS receive data output of the CAN transceiver to the CAN controller, supplied by VIO; high when bus is Recessive and low when Dominant.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SSOP-28-208mil
Category Interface
Pins 28

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage (controller) VDD 2.7 5.5 V TAMB = -40°C to +125°C 68
Register Retention Voltage VRET 2.4 V 68
High-Level Input Voltage RxCAN VIH 2 V RxCAN; max printed as VDD +1 68
High-Level Input Voltage SCK, CS, SI, TxnRTS VIH 0.7 VDD SCK, CS, SI, TxnRTS pins; min 0.7 VDD, max printed as VDD +1 V 68
High-Level Input Voltage OSC1 VIH 0.85 1 VDD OSC1; min 0.85 VDD, max VDD 68
High-Level Input Voltage RESET VIH 0.85 1 VDD RESET; min 0.85 VDD, max VDD 68
Low-Level Input Voltage RxCAN, TxnRTS VIL 0.15 VDD RxCAN, TxnRTS pins; min printed as -0.3 V, max 0.15 VDD 68
Low-Level Input Voltage SCK, CS, SI VIL 0.4 VDD SCK, CS, SI; min printed as -0.3 V, max 0.4 VDD 68
Low-Level Input Voltage OSC1 VIL 0.3 VDD OSC1; min VSS, max 0.3 VDD 68
Low-Level Input Voltage RESET VIL 0.15 VDD RESET; min VSS, max 0.15 VDD 68
Low-Level Output Voltage TxCAN VOL 0.6 V IOL = +6.0 mA, VDD = 4.5V 68
Low-Level Output Voltage RxnBF Pins VOL 0.6 V IOL = +8.5 mA, VDD = 4.5V 68
High-Level Output Voltage TxCAN, RxnBF Pins VOH 0.7 V VDD, 0.7 V minimum; IOH = -3.0 mA, VDD = 4.5V 68
High-Level Output Voltage SO, CLKOUT VOH 0.5 V VDD, 0.5 V minimum; IOH = -400 µA, VDD = 4.5V 68
Input Leakage Current, all I/Os except OSC1 and TxnRTS ILI -1 1 µA CS = RESET = VDD, VIN = VSS to VDD 68
Internal Capacitance (all inputs and outputs) CINT 7 pF TAMB = +25°C, fC = 1.0 MHz, VDD = 0V (Note 1) 68
Operating Current IDD 10 mA VDD = 5.5V, FOSC = 25 MHz, FCLK = 1 MHz, SO = Open 68
Standby Current (Sleep mode) IDDS 8 µA CS, TxnRTS = VDD, Inputs tied to VDD or VSS, -40°C to +125°C 68
Clock In Frequency FOSC 1 25 MHz 68
SPI Clock Frequency FCLK 10 MHz 70
RESET Pin Low Time tRL 2 µs 69
Wake-up Noise Filter tWF 100 ns 69
VDDA Pin Voltage Range VDDA 4.5 5.5 V 71
Supply Current, Recessive IDD 5 10 mA Recessive; VTXD = VDDA 71
Supply Current, Dominant IDD 45 70 mA Dominant; VTXD = 0V 71
Standby Current (VDDA) IDDS 5 15 µA Includes IIO 71
High Level of the POR Comparator VPORH 3.8 4.3 V 71
Low Level of the POR Comparator VPORL 3.4 4 V 71
Digital Supply Voltage Range VIO 2.7 5.5 V 71
Supply Current on VIO, Recessive IIO 4 30 µA Recessive; VTXD = VIO 71
Supply Current on VIO, Dominant IIO 85 500 µA Dominant; VTXD = 0V 71
Standby Current (VIO) IDDS 0.3 1 µA (Note 1) 71
CANH, CANL Recessive Bus Output Voltage VO(R) 2 3 V VTXD = VDDA; No load; typ printed as 0.5 VDDA 71
CANH, CANL Bus Output Voltage in Standby VO(S) -0.1 0 0.1 V STBY = VTXD = VDDA; No load 71
Recessive Output Current IO(R) -5 5 mA -24V < VCAN < +24V 71
CANH Dominant Output Voltage VO(D) 2.75 3.5 4.5 V TXD = 0; RL = 50 to 65 71
CANL Dominant Output Voltage VO(D) 0.5 1.5 2.25 V RL = 50 to 65 71
Dominant Differential Output Voltage VO(DIFF) 1.5 2 3 V VTXD = VSS; RL = 50 to 65; Figure 7-2, Figure 7-4 71
Recessive Differential Input Voltage, Normal mode VDIFF(R)(I) -1 0.5 V Normal mode; -12V < V(CANH, CANL) < +12V; see Figure 7-6 (Note 2) 72
Dominant Differential Input Voltage, Normal mode VDIFF(D)(I) 0.9 V Normal mode; -12V < V(CANH, CANL) < +12V; see Figure 7-6 (Note 2); max printed as VDDA 72
Differential Receiver Threshold, Normal mode VTH(DIFF) 0.5 0.7 0.9 V Normal mode; -12V < V(CANH, CANL) < +12V; see Figure 7-6 (Note 2) 72
Common-Mode Input Resistance RIN 10 30 kΩ (Note 1) 72
Differential Input Resistance RIN(DIFF) 10 100 kΩ (Note 1) 72
High-Level Input Voltage (TXD, STBY) VIH 0.7 V min 0.7 VIO, max printed as VIO + 0.3 V 72
Low-Level Input Voltage (TXD, STBY) VIL -0.3 V max printed as 0.3 VIO 72
RXD High-Level Output Voltage VOH 0.4 V VIO, 0.4 V minimum; IOH = -1 mA; typical -2 mA 72
RXD Low-Level Output Voltage VOL 0.4 V IOL = 4 mA; typical 8 mA 72
Shutdown Junction Temperature TJ(SD) 165 175 185 °C -12V < V(CANH, CANL) < +12V (Note 1) 72
Shutdown Temperature Hysteresis TJ(HYST) 20 30 °C -12V < V(CANH, CANL) < +12V (Note 1) 72
Propagation Delay TXD to RXD, negative edge tTXD-RXD 125 ns Negative edge on TXD 73
Propagation Delay TXD to RXD, positive edge tTXD-RXD 235 ns Positive edge on TXD 73
Delay Standby to Normal mode tWAKE 5 25 40 µs Negative edge on STBY 73
Supply Voltage VDD VDD 7 V 67
Supply Voltage VDDA VDDA 7 V 67
Supply Voltage VIO VIO 7 V 67
DC Voltage at CANH, CANL -58 58 V 67
Storage temperature -55 150 °C 67
Operating Ambient Temperature TA -40 125 °C 67
Virtual Junction Temperature TVJ -40 150 °C IEC60747-1 67
Thermal Resistance, 28L-SSOP θJA 80 °C/W 77

CAD (KiCad official)

  • Symbol: MCP25625T-E
  • Footprint: Package_SO:SSOP-28_5.3x10.2mm_P0.65mm
  • 3D model: SSOP-28-208mil (KiCad packages3D, STEP)
  • 3D model files: mcp25625t-e-ss-etched.step / mcp25625t-e-ss-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp25625t-e-ss.step / mcp25625t-e-ss.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (90 pp, sha256 e4fba63531389fbf, retrieved 2026-11-16, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF