main
History Download
Ray Publish 0.1.0 4667f20

MCP1726-2502E

Microchip Tech · Power Management Specialized - PMIC · SOIC-8

MCP1726-2502E from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Connect the unregulated or regulated input voltage source to VIN; an input capacitor of 1 µF to 10 µF is recommended for most applications.
2 VIN power_in Connect the unregulated or regulated input voltage source to VIN; an input capacitor of 1 µF to 10 µF is recommended for most applications.
3 SHDN input Active-low shutdown control: a logic-high enables the LDO output and a logic-low disables it, which also pulls PWRGD low and enters a shutdown state with about 0.1 µA typical quiescent current.
4 GND power_in Connect to a quiet circuit ground to help power supply rejection ratio and noise performance; the pin conducts only the LDO quiescent current (typically 140 µA).
5 PWRGD output Open-drain power good output that indicates VOUT is within 92% (typical) of nominal regulation, with 2% typical hysteresis for the adjustable and sub-2.5V outputs and 0.7% for fixed outputs above 2.5V.
6 CDELAY passive An external capacitor from CDELAY to ground sets the power-good power-up delay from 200 µs (no capacitance) to 300 ms (0.1 µF capacitor).
7 VOUT power_out Regulated output voltage of the LDO; a minimum output capacitance of 1.0 µF is required for stability, with ceramic, tantalum or aluminum-electrolytic capacitors supported.
8 VOUT power_out Regulated output voltage of the LDO; a minimum output capacitance of 1.0 µF is required for stability, with ceramic, tantalum or aluminum-electrolytic capacitors supported.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-8
Category Power Supply Chip
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Operating Voltage VIN 2.3 6 V Note 1 4
Input Quiescent Current Iq 140 220 µA IL = 0 mA, VIN = VR + 0.5V, VOUT = 0.8V to 5.0V 4
Input Quiescent Current for SHDN Mode ISHDN 0.1 3 µA SHDN = GND 4
Maximum Output Current IOUT 1 A VIN = 2.3V to 6.0V (Note 1) 4
Line Regulation VOUT/(VOUT x VIN) 0.05 0.3 %/V (VR + 0.5)V ≤ VIN ≤ 6V 4
Load Regulation VOUT/VOUT -1.5 0.5 1.5 % IOUT = 1 mA to 1A, VIN = (VR + 0.6)V (Note 4) 4
Voltage Regulation VOUT -2.5 0.5 2.5 % Note 2; relative to VR (printed as VR, 2.5%, VR ± 0.5%, VR + 2.5%) 4
Dropout Voltage VIN, VOUT 220 500 mV IOUT = 1A, VIN(MIN) = 2.3V (Note 5) 4
Input Voltage Operating Range for Valid PWRGD VPWRGD_VIN 1 6 V TA = +25°C 5
Input Voltage Operating Range for Valid PWRGD VPWRGD_VIN 1.2 6 V TA = -40°C to +125°C 5
PWRGD Threshold Voltage (falling edge) PWRGD_THF 88 92 96 %VOUT VOUT < 2.5V, Falling Edge 5
PWRGD Threshold Voltage (falling edge) PWRGD_THF 89 92 95 %VOUT VOUT > 2.5V, Falling Edge 5
PWRGD Threshold Voltage (rising edge) PWRGD_THR 89 94 98 %VOUT VOUT < 2.5V, Rising Edge 5
PWRGD Threshold Voltage (rising edge) PWRGD_THR 90 93 96 %VOUT VOUT > 2.5V, Rising Edge 5
PWRGD Output Voltage Low VPWRGD_L 0.2 0.4 V ISINK = 1.2 mA 5
PWRGD Time Delay TPG 10 30 55 ms CDELAY = 0.01 µF 5
Shutdown Logic-High Input VSHDN-HIGH 45 %VIN VIN = 2.3V to 6.0V 5
Shutdown Logic-Low Input VSHDN-LOW 15 %VIN VIN = 2.3V to 6.0V 5
SHDN Input Leakage Current SHDNILK -0.1 0.001 0.1 µA VIN = 6V, SHDN = VIN, SHDN = GND 5
Operating Junction Temperature Range TJ -40 125 °C Steady State 6
Maximum Junction Temperature TJ 150 °C Transient 6
Storage Temperature Range TA -65 150 °C 6
Allowable Output Voltage Range VOUT 0.8 5.5 V Section 4.1; both fixed and adjustable versions 14
Thermal Resistance, 8L SOIC, junction to air θJA 163 °C/W 4-Layer JC51-7 Standard Board 6
Thermal Resistance, 8L SOIC, junction to case θJC 42 °C/W 6

CAD (KiCad official)

  • Symbol: MCP1726-2502E
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: mcp1726-2502e-etched.step / mcp1726-2502e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp1726-2502e.step / mcp1726-2502e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (32 pp, sha256 913cb0f74fbdeae5, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF