Generated by kicad-footprint-generator · KiCad file format 20260206
MCP1726-2502E
Microchip Tech · Power Management Specialized - PMIC · SOIC-8
MCP1726-2502E from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Connect the unregulated or regulated input voltage source to VIN; an input capacitor of 1 µF to 10 µF is recommended for most applications. |
| 2 | VIN | power_in | Connect the unregulated or regulated input voltage source to VIN; an input capacitor of 1 µF to 10 µF is recommended for most applications. |
| 3 | SHDN | input | Active-low shutdown control: a logic-high enables the LDO output and a logic-low disables it, which also pulls PWRGD low and enters a shutdown state with about 0.1 µA typical quiescent current. |
| 4 | GND | power_in | Connect to a quiet circuit ground to help power supply rejection ratio and noise performance; the pin conducts only the LDO quiescent current (typically 140 µA). |
| 5 | PWRGD | output | Open-drain power good output that indicates VOUT is within 92% (typical) of nominal regulation, with 2% typical hysteresis for the adjustable and sub-2.5V outputs and 0.7% for fixed outputs above 2.5V. |
| 6 | CDELAY | passive | An external capacitor from CDELAY to ground sets the power-good power-up delay from 200 µs (no capacitance) to 300 ms (0.1 µF capacitor). |
| 7 | VOUT | power_out | Regulated output voltage of the LDO; a minimum output capacitance of 1.0 µF is required for stability, with ceramic, tantalum or aluminum-electrolytic capacitors supported. |
| 8 | VOUT | power_out | Regulated output voltage of the LDO; a minimum output capacitance of 1.0 µF is required for stability, with ceramic, tantalum or aluminum-electrolytic capacitors supported. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Operating Voltage | VIN | 2.3 | 6 | V | Note 1 | 4 | |
| Input Quiescent Current | Iq | 140 | 220 | µA | IL = 0 mA, VIN = VR + 0.5V, VOUT = 0.8V to 5.0V | 4 | |
| Input Quiescent Current for SHDN Mode | ISHDN | 0.1 | 3 | µA | SHDN = GND | 4 | |
| Maximum Output Current | IOUT | 1 | A | VIN = 2.3V to 6.0V (Note 1) | 4 | ||
| Line Regulation | VOUT/(VOUT x VIN) | 0.05 | 0.3 | %/V | (VR + 0.5)V ≤ VIN ≤ 6V | 4 | |
| Load Regulation | VOUT/VOUT | -1.5 | 0.5 | 1.5 | % | IOUT = 1 mA to 1A, VIN = (VR + 0.6)V (Note 4) | 4 |
| Voltage Regulation | VOUT | -2.5 | 0.5 | 2.5 | % | Note 2; relative to VR (printed as VR, 2.5%, VR ± 0.5%, VR + 2.5%) | 4 |
| Dropout Voltage | VIN, VOUT | 220 | 500 | mV | IOUT = 1A, VIN(MIN) = 2.3V (Note 5) | 4 | |
| Input Voltage Operating Range for Valid PWRGD | VPWRGD_VIN | 1 | 6 | V | TA = +25°C | 5 | |
| Input Voltage Operating Range for Valid PWRGD | VPWRGD_VIN | 1.2 | 6 | V | TA = -40°C to +125°C | 5 | |
| PWRGD Threshold Voltage (falling edge) | PWRGD_THF | 88 | 92 | 96 | %VOUT | VOUT < 2.5V, Falling Edge | 5 |
| PWRGD Threshold Voltage (falling edge) | PWRGD_THF | 89 | 92 | 95 | %VOUT | VOUT > 2.5V, Falling Edge | 5 |
| PWRGD Threshold Voltage (rising edge) | PWRGD_THR | 89 | 94 | 98 | %VOUT | VOUT < 2.5V, Rising Edge | 5 |
| PWRGD Threshold Voltage (rising edge) | PWRGD_THR | 90 | 93 | 96 | %VOUT | VOUT > 2.5V, Rising Edge | 5 |
| PWRGD Output Voltage Low | VPWRGD_L | 0.2 | 0.4 | V | ISINK = 1.2 mA | 5 | |
| PWRGD Time Delay | TPG | 10 | 30 | 55 | ms | CDELAY = 0.01 µF | 5 |
| Shutdown Logic-High Input | VSHDN-HIGH | 45 | %VIN | VIN = 2.3V to 6.0V | 5 | ||
| Shutdown Logic-Low Input | VSHDN-LOW | 15 | %VIN | VIN = 2.3V to 6.0V | 5 | ||
| SHDN Input Leakage Current | SHDNILK | -0.1 | 0.001 | 0.1 | µA | VIN = 6V, SHDN = VIN, SHDN = GND | 5 |
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | Steady State | 6 | |
| Maximum Junction Temperature | TJ | 150 | °C | Transient | 6 | ||
| Storage Temperature Range | TA | -65 | 150 | °C | 6 | ||
| Allowable Output Voltage Range | VOUT | 0.8 | 5.5 | V | Section 4.1; both fixed and adjustable versions | 14 | |
| Thermal Resistance, 8L SOIC, junction to air | θJA | 163 | °C/W | 4-Layer JC51-7 Standard Board | 6 | ||
| Thermal Resistance, 8L SOIC, junction to case | θJC | 42 | °C/W | 6 |
CAD (KiCad official)
- Symbol:
MCP1726-2502E - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
mcp1726-2502e-etched.step/mcp1726-2502e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp1726-2502e.step/mcp1726-2502e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (32 pp, sha256
913cb0f74fbdeae5, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).