3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMCP1630T-E
Microchip Tech · DC-DC Converters · MSOP-8
MCP1630T-E from Microchip Tech, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | COMP | output | Error amplifier output; external compensation connects from FB to COMP, and an internal clamp limits its voltage to 2.7V (typ.), setting the maximum peak switch current. |
| 2 | FB | input | Error amplifier inverting input that senses the output (voltage or current) for regulation using negative feedback. |
| 3 | CS | input | Current sense input for cycle-by-cycle peak current control (max 0.9V on MCP1630) or voltage ramp input on MCP1630V (2.7V max, common mode range VIN - 1.4V). |
| 4 | OSC IN | input | External oscillator input, typically from a microcontroller I/O; when high VEXT is driven low, and the high-to-low transition starts a new cycle. |
| 5 | GND | power_in | Circuit ground, to be connected to the analog or quiet ground plane since noise here affects the CS-to-error-amplifier comparison. |
| 6 | VEXT | output | External driver output that sets the power system duty cycle; drives a MOSFET driver logic input or directly the gate of a low-side N-channel MOSFET. |
| 7 | VIN | power_in | Input bias supply pin, normal operation 3.0V to 5.5V, with a 0.1 µF bypass capacitor to GND. |
| 8 | VREF | power_in | External reference voltage input used to regulate the output, ranging from 0V to VIN (rail-to-rail). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Operating Voltage | VIN | 3 | 5.5 | V | 6 | ||
| Input Quiescent Current | I(VIN) | 2.8 | 4.5 | mA | IEXT = 0 mA, FOSC IN = 0 Hz | 6 | |
| External Oscillator Range | FOSC | 1 | MHz | Note 1 | 6 | ||
| Oscillator Rise Time | TRISE | 0.01 | 10 | µs | Note 2 | 6 | |
| Oscillator Fall Time | TFALL | 0.01 | 10 | µs | Note 2 | 6 | |
| Oscillator Input Voltage Low | VL | 0.8 | V | 6 | |||
| Oscillator Input Voltage High | VH | 2 | V | 6 | |||
| Input Offset Voltage | VOS | -4 | 0.1 | 4 | mV | 6 | |
| Error Amplifier PSRR | PSRR | 80 | 99 | dB | VIN = 3.0V to 5.0V, VCM = 1.2V | 6 | |
| Open-loop Voltage Gain | AVOL | 85 | 95 | dB | RL =5k to VIN/2, 100 mV < VEAOUT < VIN, 100 mV, VCM = 1.2V | 6 | |
| Error Amplifier Sink Current | ISINK | 5 | 11 | mA | VIN = 5V, VREF = 1.2V, VFB = 1.4V, VCOMP = 2.0V | 6 | |
| Error Amplifier Source Current | ISOURCE | -2 | -9 | mA | VIN = 5V, VREF = 1.2V, VFB = 1.0V, VCOMP = 2.0V, Absolute Value | 6 | |
| Maximum Current Sense Signal MCP1630 | VCS_MAX | 0.85 | 0.9 | 0.95 | V | Set by maximum error amplifier clamp voltage, divided by 3. | 7 |
| Delay From CS to VEXT MCP1630 | TCS_VEXT | 12 | 25 | ns | 7 | ||
| Minimum Duty Cycle | DCMIN | 0 | % | VFB = VREF + 0.1V, VCS = GND | 7 | ||
| RDSON P-channel | RDSon_P | 10 | 30 | Ω | 7 | ||
| RDSON N-channel | RDSon_N | 7 | 30 | Ω | 7 | ||
| VEXT Rise Time | TRISE | 5.9 | 18 | ns | CL = 100 pF, Typical for VIN = 3V | 7 | |
| VEXT Fall Time | TFALL | 6.2 | 18 | ns | CL = 100 pF, Typical for VIN = 3V | 7 | |
| Under Voltage Lockout | UVLO | 2.7 | 3 | V | VIN falling, VEXT low state when in UVLO | 7 | |
| Under Voltage Lockout Hysteresis | UVLO HYS | 50 | 75 | 150 | mV | 7 | |
| Operating Junction Temperature Range | TA | -40 | 125 | °C | Steady state | 7 | |
| Storage Temperature Range | TA | -65 | 150 | °C | 7 | ||
| Maximum Junction Temperature | TJ | 150 | °C | Transient | 7 | ||
| Thermal Resistance, 8L-MSOP | θJA | 208 | °C/W | Typical 4-layer board | 7 | ||
| Supply Voltage | VDD | 6 | V | 6 | |||
| Storage Temperature | -65 | 150 | °C | 6 | |||
| Maximum Junction Temperature | TJ | 150 | °C | 6 | |||
| Continuous Operating Temperature Range | -40 | 125 | °C | 6 | |||
| ESD Protection on All Pins, HBM | 3 | kV | HBM | 6 | |||
| Min. Oscillator High/Low Time | TOH_MIN, TOL_MIN | 10 | ns | 6 | |||
| Oscillator Input Capacitance | COSC | 5 | pf | 6 | |||
| Common Mode Rejection Ratio | 80 | dB | VIN = 5V, VCM = 0V to 2.5V | 6 | |||
| Low-level Output | VOL | 25 | mV | RL = 5 k to VIN/2 | 6 | ||
| Gain Bandwidth Product | GBWP | 3.5 | MHz | VIN = 5V | 6 | ||
| Current Sense Input Bias Current | ICS_B | -0.1 | µA | VIN = 5V | 7 | ||
| Thermal Shutdown | TSHD | 150 | °C | 7 | |||
| Thermal Shutdown Hysteresis | TSHD_HYS | 18 | °C | 7 |
CAD (KiCad official)
- Symbol:
MCP1630T-E - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
mcp1630t-e-etched.step/mcp1630t-e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp1630t-e.step/mcp1630t-e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (30 pp, sha256
b35ca236142a63cd, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).